Sony Bdv E800w Operating Instructions

11GB
About the indications in the front panel display
ACurrent surround format
BLights up when a station is received. 
(Radio only) (page 56)
CLights up when stereo sound is 
received. (Radio only) (page 56)
DLights up when outputting a video 
signal with the NTSC color system.
ELights up when the external memory is 
recognized. (page 28)
FLights up when the HDMI OUT jack is 
correctly connected to an HDCP (High-
bandwidth Digital Content Protection)-
compliant device with HDMI or DVI 
(Digital Visual...

12GB
ALAN (100) terminal (page 29)
BCOMPONENT VIDEO OUT jacks (page 
22)
CVIDEO OUT jack (page 22)
DEZW-RT10 slot (page 27)
ECOAXIAL 75Ω FM jack (page 26)
FA.CAL MIC jack (pages 33, 69)
GAUDIO (AUDIO IN L/R) jacks (page 25)
HTV (AUDIO IN L/R) jacks (page 24)
IS-AIR ID switch (pages 31, 61)JEXT slot (page 28)
KTV (DIGITAL IN OPTICAL) jack (page 
24)
LSAT/CABLE (DIGITAL IN COAXIAL) 
jack (page 25)
MDMPORT (DIGITAL MEDIA PORT) jack 
(page 25)
NHDMI OUT jack (page 22)
OSPEAKER jacks (page 20)
Rear panel...

13GB
APHONES jack (page 31)
BPOWER (ON/OFF) (pages 31, 61)
CPOWER / ON LINE indicator (pages 31, 
61)
DPAIRING indicator (page 63)
EPAIRING (page 63)FWireless transceiver (EZW-RT10) slot 
(page 27)
GS-AIR ID switch (pages 31, 61)
HSPEAKER L jack (page 20)
ISPEAKER R jack (page 20)
JSURROUND SELECTOR switch (pages 
31, 61)
Surround amplifier
PHONESPOWER
POWER/ON LINE
Front panelRear panel
RSURROUND SELECTOR
S-AIR ID
EZW-RT10
SPEAKER
SURROUND
PA I R I N GCB
A
SURROUND
BACK
L
 

14GB
Getting Started
Step 1: Installing the System
For the best possible surround sound, place all speakers at the same distance from the listening position 
(A). The distance can be between 0.0 to 7.0 meters.
If you cannot place the center speaker and surround speakers at the same distance as (A), place them 
within 7.0 meters of the listening position.
Place the surround speakers to the rear of the listening position (B).
The subwoofer can be placed anywhere in the room.
Note Use caution when placing...

15GB
Getting Started
To add the optional surround back speakers
You can enjoy 7.1 surround sound by purchasing the Wireless Surround Speaker Kit (WAHT-SBP1, 
optional). The optional product lineup differs depending on the area.
For the position of the surround back speakers, refer the illustration below (C).
4545
3030
CC
Front left speaker (L)
Front right speaker (R) Center speaker
Subwoofer
Surround back right speaker (R)
(optional) Surround back left speaker (L)
(optional) Surround left
speaker...

16GB
Getting Started
Caution
 Contact a screw shop or installer regarding the wall material or screws to be used.
 Use screws that are suitable for the wall material and strength. As a plaster board wall is especially fragile, attach 
the screws securely to a beam and fasten them to the wall. Install the speakers on a vertical and flat wall where 
reinforcement is applied.
 Sony is not responsible for accidents or damage caused by improper installation, insufficient wall strength or 
improper screw...

17GB
Getting Started
3Disassemble the speaker by lifting the upper part of the speaker.
4Pull out the speaker cord from the bottom of the lower part of the speaker.
The removed speaker cord is used when installing the speaker on a wall.
Upper part
Lower part
Rear of the speaker
Lower part of the speaker
,
Speaker cord
 

18GB
Getting Started
Fully-disassembled illustration
To install the speakers on a wall
Before installing the speakers on a wall, connect the speaker cord to the speaker.
Be sure to match the speaker cords to the appropriate terminals on the speakers: the speaker cord with 
the color tube to 3, and the speaker cord without the color tube to #.
1Prepare screws (not supplied) that are suitable for the hole on the back of each speaker. 
See the illustrations below.
2Fasten the screws to the wall.
Upper part...

19GB
Getting Started
3Hang the speakers on the screws.
5 mm
10 mmHole on the back of 
the speaker
Rear of the speaker
 

20GB
Getting Started
Step 2: Connecting the System
For connecting the system, read the information on the following pages.
Do not connect the AC power cord (mains lead) of the unit to a wall outlet (mains) until all the other 
connections are made.
Note When you connect another component with a volume control, turn down the volume of the other components to a 
level where sound is not distorted.
The connector of the speaker cords and the color tube are color-coded depending on the type of speaker....