Sony DPP FP65 User Manual

							11 GB
Preparations
3Close the paper tray cover.
4Open the slide cover.
5Insert the paper tray into the printer.
Notes
 You can set up to 20 sheets of print paper. Riffle 
the print paper thoroughly. Insert the print paper 
with the protective sheet facing up. Then remove 
the protective sheet.
 Insert the print paper with its printing surface (the 
side with no imprint) facing up.
 Do not touch the printing surface. Fingerprints or 
contamination on the printing surface may result in 
imperfect printing.
 Do not bend the print paper, or cut the print paper 
from the perforations before printing. To avoid paper jam or malfunctions of the printer, 
make sure of the following before printing:
– Do not write or type on the print paper.
–  Do not attach a sticker or stamps on the print 
paper.
– When adding print paper to the paper tray, be 
sure that the total number of print paper sheets 
does not exceed 20 sheets.
– Do not insert different types of print paper 
together into the paper tray.
– Do not print on used print paper. Printing an 
image twice on the same paper will not make 
the printed image thicker.
– Use the print paper for this printer only.
–  Do not use print paper ejected without printing.
Notes on storing the print paper
 To store print paper in the tray, remove the paper 
tray from the printer and close the slide door of the 
paper tray.
 Avoid storing the paper with the printed faces 
touching each other or in contact with rubber or 
plastic products, including vinyl chloride or 
plasticizer for an extended period of time; color 
changes or deterioration of the printed image may 
occur.
 Avoid placing the print paper in a location subject 
to high temperatures, high humidity, excessive 
dust or direct sunlight.
 When you are going to store partially-used print 
paper, store it in its original bag or a similar 
container.
Downloaded From ManualsPrinter.com Manuals 
						

							12 GB
Connecting to the AC 
power source
1Insert the plug of the AC adaptor 
into the DC IN 24 V jack on the back 
of the printer.
2Connect one plug of the AC power 
cord to the connector of the AC 
adaptor and the other plug to the 
wall outlet.
Notes
 Do not place the printer in an unstable location 
such as on a wobbly table.
 Leave enough room around the printer. The print 
paper emerges from the back a few times during 
printing. Keep 10 cm (13/32 inch) or more space at 
the rear of the printer.
 Connect the AC adaptor to an easily accessible 
wall outlet close by. If trouble occurs while using 
the adaptor, immediately shut off the power by 
disconnecting the plug from the wall outlet.
 Do not short the plug of the AC adaptor with a 
metallic object, as this may cause a malfunction.
 Do not use the AC Adaptor placed in a narrow 
space, such as between a wall and  furniture.
 When you have finished using the AC adaptor, 
disconnect the AC power cord from the
DC IN 24 V jack of the printer and from the AC 
power sources.
 The printer is not disconnected from the AC power 
source (mains) as long as it is connected to the wall 
outlet, even if the printer itself has been turned off.
To use your Printer abroad - 
Power sources
You can use your Printer and the AC Adaptor 
(supplied) in any country or region where the 
power supply is within 100 V to 240 V AC, 
50/60 Hz. Use a commercially available AC 
plug adaptor [a], if necessary, depending on the 
wall outlet (wall socket) [b].
Do not use an electronics transformer (travel 
converter), as this may cause a malfunction.
AC adaptor
AC power cordTo the wall 
outlet 10 cm 
(13/32
inches)
AC-S2416
Downloaded From ManualsPrinter.com Manuals 
						

							13 GB
  Direct printing
Direct printing
LCD screen display
You can change the image preview view by 
setting the “On-screen Display” from the  
menu. (page 27)
AAccess indicationAppears while the printer is accessing a 
memory card or a USB memory. 
Note
While the access indication is displayed, do not 
remove a memory card or a USB memory, or do 
not turn off the power. Data may be damaged.
BInput/setting indicationsInput indications and settings information for 
an image are displayed.
CNumber of  selected images/Total 
number of image
DInk ribbon indication
: P size
: Cleaning cartridge
EImage file information (file format, 
file size, image number (folder- file 
number)*)
(*DCF-compatible files only. In case of other 
file formats, only part of file name will be 
displayed.)
FOperation tips
GShot or Saved date (year/month/
day)
HPrint quantity setting
An image preview
On-screen Display: On
On-screen Display: OffIcons Meaning
“Memory Stick” input
SD Memory Card input
xD-Picture Card input
USB Memory input
DPOF print preset indication
Continued
Downloaded From ManualsPrinter.com Manuals 
						

							14 GB
Displays a list of the images stored in the 
selected media. 
DPP-FP65
DPP-FP75
ACursor (orange frame)You can move the cursor (selection) by 
pressing g/G/f/F.
BPrint quantity settingAppears only when the print quantity is being 
set.
CScroll barIndicates the position of the image among the 
total number of images.
DDPOF print preset indicationImage list
Switching an image preview 
and image list
You can switch the display as follows:
 To display the image list
In an image preview, press the   
(Index View) button.
When there are multiple pages, you can 
switch pages by pressing  f/F.
 To display an image preview
In the image list, press g/G/f/F to move 
the cursor to the desired image and press 
ENTER. 
In an image preview, you can change the 
displayed image by pressing g/G .
To enlarge an image
In the image preview window, press 
ENTER. Each time you press the button, 
the image is enlarged up to 5 times the 
original scale:  x1.5, x2, x3, x4, and then 
x5.  In an enlarged image preview, you 
can change the portion to be displayed by 
pressing g/G/f/F.  
   
 x1  c  x1.5  c   x2  c  x3  c x4  c  x5
r
Downloaded From ManualsPrinter.com Manuals 
						

							15 GB
Direct printing
The following are the icons displayed on the 
LCD screen.
You can proceed with operations by selecting a 
desired icon with g/G/f/F, and then pressing  
ENTER.
For detailed explanations, see the pages in the 
parentheses.
List of icons
Icons Meaning
Edit (21)
Layout Print (23)
ID Photo (24)
Batch Print (25)
Print setup (26)
Edit/Layout Print/ID Photo
Enlarging and reducing an image 
size (21)
Moving an image (21)
Rotating an image (21)
(Rotates 90° Clockwise.)
Adjusting the picture quality of an 
image (21)
Changing a photo into a 
monochrome one (24) 
* This option is available only in  ID 
Photo operations.
Resetting edits (22)
Printing an edited image (22)
Exiting the menu (23)
Batch Print
Index Print (25)
(Prints all the images in split 
screens.)
Print All (25)
(Prints one copy each for all the 
images.)
DPOF Print  (25)
(Prints the images with the print 
mark ( ) in an image 
preview with the preset number of 
copies in the order they are 
displayed.)
Print setup
Date Print (26)
Borders/Borderless (26)
On-screen Display (27)
Color Setting (28)
Printer information display (29)
Default Setting (29)
(Resets the settings to the factory-
preset default settings.) Icons Meaning
Downloaded From ManualsPrinter.com Manuals 
						

							16 GB
Basic printing
Prepare a memory card that contains images for 
printing: “Memory Stick”, “Memory Stick 
Duo”, SD Memory Card, or an xD-Picture 
Card. 
Insert the desired card with its labelled 
surface facing up into the proper slot until it 
clicks firmly into place. 
For the types of memory cards you can use 
with the printer, please see pages 61 to 63.
From the left, with the label side facing up, 
“Memory Stick”, (“Memory Stick Duo”), SD 
Memory Card, and xD-Picture Card 
To eject a memory card
Remove the memory card from the slot slowly 
in the reverse direction it was inserted.
Notes
 Insert only the memory card that you want to use 
for printing. When multiple memory cards are 
inserted, the memory card inserted first will have 
the first priority.  
 The printer supports both standard and small sizes. 
A “Memory Stick Duo” adaptor is not necessary.
 To use a memory card, follow the notes 
described on pages 61 to 63.
This section explains how to display the images 
of a memory card or a USB memory on the 
printer’s LCD screen and print the selected 
images (direct printing). For how to print from 
a USB memory, see page 30.
Setting the print quantity
1Press 1 (on/standby) to turn on the 
printer.
The standby indicator turns off. An image 
stored in the memory card or USB 
memory is displayed on the LCD screen.
2Press g/G to display the image that 
you want to print.
3Set the print quantity.
To print one copy of the displayed image, 
skip this procedure and go on to the next 
step.
Press f to display the print quantity 
indication. Then specify the print quantity 
with f/F.
Inserting a memory card
Printing selected images
Downloaded From ManualsPrinter.com Manuals 
						

							17 GB
Direct printing
4Press PRINT.
While the PRINT button is lit in green, the 
printer is ready for printing. The image 
being displayed is printed. 
To print multiple images
Repeat steps 2 and 3.
To change the print quantity 
Display the image whose print quantity 
you want to change, and change the print 
quantity with f/F. 
If you select “0”, printing is canceled.
Enlarging an image to be 
printed (Trimming Print)
Press ENTER repeatedly until the image is 
enlarged to the desired size. You can enlarge an 
image up to the 5 times the original scale. Press 
g/G/f/F to move an image. 
Press PRINT to display the image preview for 
printing. Then press PRINT again to print the 
previewed image. 
Even if you have set a print quantity for other 
images, only the previewed image is printed.
Notes
 Never move or turn off the printer while it is 
printing; the ink ribbon or print paper may become 
stuck. If you turn off the power accidentally, keep 
the paper tray inserted and turn on the printer 
again. If paper being printed remains in the printer, 
remove the paper that emerges automatically and 
resume printing. 
 Do not remove the paper tray during printing. 
Otherwise, a malfunction may occur.
 The print paper emerges a few times during 
printing. Do not touch nor pull the emerged paper 
during the printing process.
 If print paper is jammed, see page 58.
On selecting input
The printer is not equipped with an input select 
switch. When you connect a memory card or a 
USB memory to the printer, images from the 
connected media are displayed automatically. 
If multiple memory cards or a USB memory 
are connected, the media first connected has the 
priority.
When you turn on the printer with multiple 
media inserted or connected, the printer detects 
the media in the order of “Memory Stick”, SD 
Memory Card, xD-Picture Card, and then a 
USB memory connected to the PictBridge/EXT 
INTERFACE connector.
Downloaded From ManualsPrinter.com Manuals 
						

							18 GB
Enjoying various printing
z Operation using the printer buttons
                                                                                 MENU
Press the   (Red-eye Correction) button to correct the red-eye phenomenon of an image 
automatically.
Press MENU and then select an icon of the desired operation.
Red-eye Correction .page 20
Red-eye Correction
A variety of printing
g/G/f/F to select the desired icon and 
press ENTER.
1 Edit
2 Layout Print
3 ID Photo Print
4 Batch Print
5 Print setup
 To exit the menu, press MENU again.
Downloaded From ManualsPrinter.com Manuals 
						

							19 GB
Direct printing
You can adjust the size, position, hue or other picture property of the selected image. 
You can place multiple photos on split screens to make a print     
You can specify the desired width and height of a photo.          
You can print a large number of images of a memory card or USB memory at one time.
You can change the settings during printing, the printer settings, and on-screen display 
settings. 
1 Edit .page 21
For the icons you can use, see page 15.
2 Layout Print .page 23
You can make a print with 2-split, 4-split, 9-split, 13-split or 
16-split images.
3ID Photo Print  .page 24
You can use a photo for an identification card such as a 
passport.
4 Batch Print .page 25
You can select from batch print options such as “Print All”, 
“Index Print”, and “DPOF Print”. 
5 Print setup .page 26
Downloaded From ManualsPrinter.com Manuals 
						

							20 GB
Red-eye Correction
1Display an image that you want to 
adjust and then press   (Red-
eye Correction).
Red-eye Correction of the selected image 
starts. The results of the adjustment will 
be displayed on the screen. 
To display the original image 
(Before correction) again
Press   (Red-eye Correction). To 
display the adjusted image, press   
again.
To cancel correction
Press CANCEL. 
Tip
Although you can check the red-eye correction 
status by pressing ENTER and enlarging an 
image, the image to be printed is not enlarged. 
To print an enlarged and red-eye-corrected 
image, first enlarge an image and then perform 
red-eye correction.
If you have set print quantity for 
multiple images
All the images with print quantity settings 
are adjusted. To display other images, 
press g/G.
To set the print quantity 
Before you start red-eye correction, set the 
print quantity (page 16). You cannot set or 
change print quantity after you finish the 
red-eye correction. To change the print 
quantity setting, cancel the red-eye 
correction.
Tips
 If there are no images with print quantity 
settings, the Red-eye Correction adjusts the 
image being previewed.
 If there are other images with print quantity 
setting, and print quantity is not specified 
for the image being previewed, the image 
being previewed will not be corrected. The 
images with print quantity settings will be 
adjusted.
 If you enlarged an image, only the enlarged 
image will be adjusted and then printed. 
2Press PRINT.
Printing of the image being adjusted starts. 
When the print quantity setting is 
specified, the specified number of copies 
are printed.
Tips
 Adjustment takes effect only on the image being 
printed. The original image will not be adjusted.
 You cannot perform editing on an image after 
Red-eye Correction.
Notes
 Depending on the image, the red-eye phenomenon 
may not be corrected. 
 When you cancel the edits by selecting   (Reset) 
in the Edit menu, the Red-eye Correction will also 
be cancelled.
 During the Red-eye Correction process, an 
animation to show reading and handling of data 
from a memory card or a USB memory will be 
displayed. While the animation is displayed, do not 
remove the memory card or disconnect USB 
memory.
The automatic red-eye 
correction of this printer uses 
the technology of FotoNation 
Inc. in the U.S.A.
Downloaded From ManualsPrinter.com Manuals