Sony Projector VPL-FHZ700L User Manual

31The Connection/Power Menu
Adjustments and Settings Using a Menu
*10:When “Standby Mode” is set to “Low,” the network and network control function cannot be 
operated while the projector is in standby mode. 

32The Installation Menu
The Installation Menu
The Installation menu is used for installing the projector.
Setting items Description
Edge BlendingOn/Off: When set to “On,” the Edge Blending function is enabled. Set to 
“Off” when you do not project using multiple projectors.
Blending 
RangeSets the edge blending width.
After selecting the blending position, a marker will be displayed.
To p : Adjusts the top width of the screen.
Bottom: Adjusts the bottom width of the screen.
Left: Adjusts the left width...

33The Installation Menu
Adjustments and Settings Using a Menu
Installation AttitudeLink to Image Flip/Right Side Up/Upside Down/Front Down/Front Up/
Portrait 1/Portrait 2: Change the cooling setting to suit to the installation 
attitude. When set to “Link to Image Flip,” the cooling setting changes 
based on the setting of “Image Flip.”
*7 Continuing to use the wrong setting 
may affect component reliability.
High Altitude ModeOn/Off: Set to “On” when using the projector at an altitude of 1,500 m or...

34The Installation Menu
*1: You cannot adjust anything other than the targeted adjustment zones in “Zone Black Level Adj.”
*2: When selecting the correction zone of “Zone Black Level Adj.,” the targeted correction zone 
flashes twice.
*3: If the Screen Aspect is set to 16:10 and input signal is 16:10 or 16:9, the image will be projected 
at the correct aspect. This function is not available when displaying two pictures. 
*4: When “Edge Blending” is set to “On,” “Screen Fitting” (HV Keystone/Warping) is...

35The Information Menu
Adjustments and Settings Using a Menu
The Information Menu
The Information menu enables you to confirm various information on the projector, such as the 
total usage hours of a light.
*1: These items may not be displayed depending on the input signal.Items Description
Model Name Displays the model name.
Serial No. Displays the serial number.
fH / fV (horizontal 
frequency/vertical 
frequency)
*1
Displays the horizontal frequency/vertical frequency/signal type of the 
current input...

36Using Network Features
BNetwork
Using Network 
Features
Connection to the network allows you to 
operate the following features:
 Checking the current status of the 
projector via a Web browser.
 Remotely controlling the projector via a 
Web browser.
 Receiving the e-mail report for the 
projector.
 Making the network settings for the 
projector.
 Supports network monitoring and control 
protocol (Advertisement, PJ Talk, PJ Link, 
SNMP, AMX DDDP [Dynamic Device 
Discovery Protocol], Crestron...

37Using Network Features
Network
How to operate the Control window
Switching the page
Click one of the Page Switching buttons to 
display the desired setting page.
Setting the access limitation
You can limit a user for accessing any 
particular page.
Administrator: Allowed access to all 
pages
User: Allowed access to all pages except 
the Setup page
Set under [Password] of the Setup page.
When you access the Setup page for the first 
time, enter “root” for the user name and 
enter “Projector” for the...

38Using Network Features
Entered values will not be applied unless 
you click on [Apply].
1Click on [Owner information] to enter 
the owner information recorded in the 
e-
mail report.
2Set the timing of the e-mail report.
Click on [Mail Report] to open the Mail 
Report page.
Maintenance Reminder: Set the timing 
for maintenance. To reset 
Maintenance Reminder, check the 
RESET check box and then click on 
[Apply].
3Enter the outgoing e-mail address in 
the Email Address box then check the 
Report Timing...

39Indicators
Others
BOthers
Indicators
The indicators allow checking the status and notify you of abnormal operation of the projector.
If the projector exhibits abnormal status, address the problem in accordance with the table 
below.
ON/STANDBY indicator
WARNING indicator
StatusMeaning/Remedies
Lights in red The projector is in standby mode.
Flashes in green  The projector is ready to operate after having been turned on. 
 The light source cools after the projector is turned off.
Lights in green The...

40Messages List
Messages List
When any of the messages listed below appears on the projected image, address the problem in 
accordance with the table below.
MessageMeaning/RemedyPage
Clean the filter.
Projector temperature is 
high. The light will turn 
off in 1 minute.Check the items below.
 Check to see if nothing is blocking the ventilation holes.
 Check to see if the air filter is not clogged.
 Check if “Installation Attitude” on the Installation menu is 
correctly selected.3, 33, 
43
Frequency is...