Sony Projector VPL-VW500ES User Manual

41Connecting the unit to the network
Using Network Features
Connecting the unit 
to the network
1Connect the LAN cable.
2Set the network settings for the unit 
using “Network Setting” on the 
Installation  menu (page 39).
Supported network monitoring and 
control protocols

 SDCP (PJ Talk) 
 DDDP (AMX)
The network functions above are constantly 
enabled.
Using Network Features
Note
LAN 
Connector LAN cable 
(straight type) 
(not supplied)
Hub, router, etc. 

42Troubleshooting
Troubleshooting
If the unit appears to be operating erratically, try to diagnose and correct the problem using the 
following instructions. If the problem persists, consult with qualified Sony personnel.
Power
Picture
Error Handling
SymptomCause and RemedyPage
The power is not turned 
on.The power may not turn on if you turn the power off with ?/
1 (ON/STANDBY) button and turn it on again in a short 
time. After about 1 minute, turn the power on.–
Close the lamp cover securely, then...

43Troubleshooting
Error Handling
On-screen display
Remote control
The color of characters or 
the picture is not 
appropriate.Select the desired color registration in “Panel Alignment” of 
the Installation   menu.38
Image is left on the 
screen. (image retention)When high contrast non-moving images are displayed for a 
long period of time, there may be some image retention on 
the screen. This is only a temporary condition. Turning off 
the power for a while will eliminate the retained image.–...

44Troubleshooting
3D video images
Others
SymptomCause and RemedyPage
The video image does not 
seem like 3D video 
images.Check if the 3D glasses are turned on. 15
Make sure that the battery in the 3D glasses could be weak 
or is sufficiently charged.–
Set “2D-3D Display Sel.” to “Auto” or “3D.” 34
Check if the input signals are compatible 3D signals. 56
The 3D signals may not be input depending on the 
specifications of the connected AV selector/AV amplifier/
external equipment. If the 3D signal is not...

45Warning Indicators
Error Handling
Warning Indicators
The ON/STANDBY or WARNING indicator lights up or flashes if there is any trouble with 
your projector.
When a warning indicator other than the above starts flashing, and the symptom persists even after 
carrying out the above methods, consult with qualified Sony personnel. 
Flashing/Lighting indicatorsThe number of 
flashesCause and Remedy
Twice Close the lamp cover securely, then tighten 
the screws securely (page 49).
Three times The temperature of...

46Message Lists
Message Lists
Warning messages
Caution messages
SymptomCause and RemedyPage
High temp.! Lamp off in 
1 min.Turn off the power. –
Check to ensure that nothing is blocking the ventilation 
holes.3, 4
Frequency is out of 
range!Frequency is out of range. Input a signal that is within the 
acceptable frequency range of the unit.53
Please replace the Lamp. It is time to replace the lamp. Replace the lamp.
If this message appears again after you replace the lamp, the 
lamp replacement process...

47Updating the Software / About the x.v.Color / About the simulated 3D feature
Others
Updating the 
Software
You can download files to update the 
software of the unit. Copy the downloaded 
files to your USB memory, insert the USB 
memory to the USB terminal of the unit, 
then perform the update.
To use the features updated, insert a USB 
memory device into a PC connected to the 
internet.
Download the update files from the 
following Sony website:
http://www.pro.sony.eu/pro/article/...

48Replacing the Lamp
Replacing the Lamp
The lamp used for the light source has a 
certain lifespan. When the lamp dims, the 
color balance of the picture becomes 
strange, or “Please replace the Lamp.” 
appears on the screen, the lamp may be 
exhausted. Replace the lamp with a new one 
(not supplied) without delay.
Tools you need to get started:
 Projector Lamp LMP-H260 (Optional)
 Standard Phillips screwdriver
 Cloth (for scratch protection)
Caution
 The lamp remains hot after the unit is 
turned off...

49Replacing the Lamp
Others
5Loosen the 3 screws on the lamp with 
the Phillips screwdriver. Hold up the 
handle, then pull the lamp straight out.
 Do not loosen other screws except the 3 
specified screws.
 Hold the lamp by the handle to remove 
and attach it.
6Push in the new lamp by the handle 
securely until it reaches the end, and 
then tighten the 3 screws.
Be careful not to touch the optical block 
inside the unit.
7Close the lamp door (inner cover), and 
then tighten the screw.
8Close the lamp...

50Replacing the Lamp
10Turn on the unit, then select the lamp 
setting item on the Setup   menu.
The menu screen below will be 
appeared.
Tip
If “Settings Lock” is set to “Level B,” set to 
“Off” once.
11Select “Yes.”
Caution
Do not put your hands into the lamp 
replacement slot, and do not allow any liquid 
or other objects into the slot to avoid 
electrical shock or fire.
 The unit will not turn on unless the lamp is 
securely installed in place.
 The unit will not turn on unless the lamp 
cover are...