Sony Projector Vpl Vw80 User Manual

							61 
Others
This section describes about the other functions, how to solve the problems, how to 
replace the lamp and air filter, etc.
About the Control for 
HDMI
What is the Control for HDMI?
Control for HDMI is an HDMI standard 
mutual control function which uses the 
HDMI CEC (Consumer Electronics 
Control) specification. By connecting a 
variety of Sony Control for HDMI 
compatible equipment such as a hard disk 
Blu-ray Disc player, a DVD player/recorder, 
an AV amplifier, etc. to a Sony Control for 
HDMI compatible TV or a projector with an 
HDMI cable, the equipment connected will 
synchronize with the TV or the projector 
when either is operated.
Using the Control for HDMI 
function
 Connect and assign the settings of each 
equipment appropriately.
 Do not turn off the main power of the 
equipment.
 Set the input setting of the projector to the 
HDMI input which the equipment is 
connected.
 Check if the picture from the equipment 
appears appropriately on the projector.
 The Control for HDMI function is 
available only between Sony Control for 
HDMI compatible equipment.
Connecting a Control for HDMI 
compatible equipment
Use an HDMI cable to connect the projector 
and the Control for HDMI compatible 
equipment. Use a cable that has acquired the 
HDMI logo.
Setting the Control for HDMI
Be sure to assign the appropriate 
connections for both the projector and the 
Control for HDMI compatible equipment 
connected to the projector. For settings of 
the projector, see page 55. For settings of the 
Control for HDMI compatible equipment 
connected to the projector, refer to its 
operational instructions. When a Sony 
equipment that is compatible with the 
“Control for HDMI - Easy Setting” is 
connected to the HDMI input of the 
projector, if you turn the Control for HDMI 
function setting of the projector on, the 
Control for HDMI function setting of the 
connected equipment will also turn on.
What you can do with the 
Control for HDMI
 Basic operations (playback, stop, menu 
operations, etc.) of the connected 
equipment is available by using the remote 
control of the projector.
 By turning on or playing back the 
connected equipment, the projector will 
turn on and the input setting will switch to 
the terminal of the connected equipment 
automatically.
 By turning the power of the projector off, 
the power of the connected equipment will 
also turn off automatically.
 By selecting equipment connected to the 
projector desired to operate with SYNC 
MENU button on the remote control of the 
projector, the power of the selected 
equipment will turn on and the input will 
switch to the terminal of the connected 
equipment automatically.
 By changing the language setting of the 
projector, the language setting of the 
connected equipment will also change to 
the same language automatically.
Others 
						

							 62
 The available functions of the Control for 
HDMI differ depending on each 
equipment. Refer to the operating 
instruction of each equipment.
 Some synchronization may be available 
with equipment of other brands with 
similar functions, but it is not guaranteed.
About the x.v.Color
 “x.v.Color” is a promotion name given to 
the products that have the capability to 
realize a wide color space based on the 
xvYCC specifications and is a trademark 
of Sony Corporation.
 xvYCC is an international standard of the 
technical specifications of the extended-
gamut color space for video signals. The 
color gamut of xvYCC is wider than the 
one of sRGB that is used with the current 
television system.
Notes 
						

							63 
Others
Troubleshooting
If the projector appears to be operating erratically, try to diagnose and correct the problem 
using the following instructions. If the problem persists, consult with qualified Sony 
personnel.
Power
Picture
Symptom Cause and Remedy
The power is not turned on.cThe power may not turn on if you turn the power off with ?/1 
(ON/STANDBY) switch and turn it on again in a short time.
After about 1 minute, turn the power on. 
cClose the lamp cover securely, then tighten the screws securely. 
(1 page 70)
cClose the filter holder securely. (1 page 71)
cCheck warning indicators. (1 page 66)
Symptom Cause and Remedy
No picture.cCheck that the proper connections have been made.
 (1 page 18)
cSelect the input source correctly using the INPUT button.
 (1 page 30)
cSet the computer signal to output from an external monitor.
cSet the computer signal to output only to an external monitor.
cSelect “Computer,” “Component” or “Video GBR” for “Input-A 
Signal Sel.” on the Setup   menu according to the input 
signal. (1 page 54)
The picture from the 
INPUT A connector is 
colored strange.cSelect “Computer,” “Component” or “Video GBR” for “Input-A 
Signal Sel.” on the Setup   menu according to the input 
signal. (1 page 54)
The picture from the 
VIDEO INPUT or 
S VIDEO INPUT 
connector is colored 
strange.cAdjust the picture of the Picture   menu. (1 page 46)
cSet “Color System” in the Setup   menu to match the color 
system being input. (1 page 54)
The bright area of the 
picture may become 
unclear or texts may 
become faded. (When 
HDMI video signal is 
input)cThis symptom may occur when a signal other than those of 
HDMI standard is input. (1 page 31) Switch the RGB dynamic 
range of the connected equipment to Limited (16-235). If this 
adjustment is unavailable, adjust “Brightness”, “Contrast”, or 
“Sharpness” in the Picture   menu of the projector. 
(1 pages 47, 48)
The texts may become 
faded when connected with 
a computer. (When 
computer signal is input)cThis symptom may occur when a signal other than those of 
HDMI standard is input. (1 page 31) Adjust “Sharpness” in the 
Picture  menu. (1 page 48) 
						

							 64
On-screen display
Remote control
The picture is too dark.cAdjust the “Contrast” or “Brightness” of the Picture   menu 
properly. (1 pages 47, 48)
The picture is not clear.cAdjust the focus. (1 page 26)
cCondensation has accumulated on the lens. Leave the projector 
for about 2 hours with the power on.
The picture flickers.cFor pictures from a computer, activate “APA” and adjust the 
current input signal.
cAdjust “Phase” for “Adjust Signal” in the Screen   menu 
properly. (1 page 52)
The color of characters or 
the picture is not 
appropriate.cSelect the desired color registration in “Panel Alignment” of 
Installation  menu (1 page 58).
Image is left on the screen. 
(image retention)cWhen high contrast non-moving images are displayed for a long 
period of time, there may be some image retention on the 
screen. This is only a temporary condition. Turning off the 
power for a while will eliminate the retained image. Symptom Cause and Remedy
Symptom Cause and Remedy
On-screen display does not 
appear.cSet “Status” in the Setup   menu to “On.” (1 page 53)
cCheck if the ON/STANDBY indicator should light in green.
The model name does not 
disappear from the screen. 
Or else, the demo mode is 
displayed continuously.cThe display mode of the projector may be set at the time of 
purchase. Consult with your local dealer or qualified Sony 
personnel.
Symptom Cause and Remedy
The remote control does 
not work.cBatteries could be weak. Replace them with new batteries. 
(1 page 11)
cInsert the batteries with the correct polarities. (1 page 11)
cIf there is a fluorescent lamp near the remote control detector, the 
projector may work improperly or inadvertently. 
cSet “IR Receiver” to “Front & Rear” on the Installation   menu 
(1 page 57). 
						

							65 
Others
Others
Symptom Cause and Remedy
The fan is noisy.cCheck the setting of “Cooling Setting” in the Setup   menu. 
(1 page 53)
cMake sure that the room temperature is not too high.
cCheck the installation conditions. (1 page 12)
The number of fan rotation increases to maintain the product 
reliability of the projector’s components in a room, where the 
temperature is higher than normal. The fan noise becomes 
slightly louder. The approximate normal temperature is 25°C.
The lens shift cannot be 
adjusted.cThe lens shift cannot be adjusted over the range of movement. 
Adjust the lens shift within the range of movement. (1 
pages 14, 25). 
						

							 66
The ON/STANDBY or LAMP/COVER indicator lights up or flashes if there is any 
trouble with your projector.
Warning Indicators
Symptom Cause and Remedy
LAMP/COVER flashes in 
red. (A repetition rate of 2 
flashes)cClose the lamp cover securely, then tighten the screws securely. 
(1 page 70)
cClose the filter holder securely. (1 page 71)
LAMP/COVER flashes in 
red. (A repetition rate of 3 
flashes)cThe lamp has reached the end of its useful lifespan. Replace the 
lamp. (1 page 69)
cThe lamp has reached a high temperature. Wait until the lamp 
cools, and then turn on the power again. 
ON/STANDBY flashes in 
red. (A repetition rate of 4 
flashes)cThe fan is broken. Consult with qualified Sony personnel.
ON/STANDBY flashes in 
red. (A repetition rate of 2 
flashes)cThe internal temperature is unusually high. Check to ensure that 
if nothing is blocking the ventilation holes or whether or not the 
projector is being used at high altitudes.
ON/STANDBY flashes in 
red. (A repetition rate of 6 
flashes)cPress the 
?/1 (ON/STANDBY) switch to turn on the projector. If 
the power is not turned on, disconnect the AC power cord, then 
confirm the ON/STANDBY lamp is turned off. After about 10 
seconds, reconnect the AC power cord and turn on the power 
again. If the indicators still light up, the electrical system has a 
problem. Consult with qualified Sony personnel.
ON/STANDBY indicator LAMP/COVER indicator 
						

							67 
Others
When a warning indicator other than the above starts flashing, and the symptom persists even after 
carrying out the above methods, consult with qualified Sony personnel. 
Warning messages
ON/STANDBY flashes in 
red. (A repetition rate of 5 
times)cThe lens protector is not fully open. Turn the power of the 
projector off and then on again. If the lens protector still does not 
fully open, consult with qualified Sony personnel.
Tip
In an urgent situation, refer to the illustration below to open the lens 
protector with your hands. Press the 
?/1 (ON/STANDBY) switch to 
turn the power on and operate the projector.
Note
Message Lists
Message Cause and Remedy
High temp.! Lamp off in 1 
min.cTurn off the power.
cCheck to ensure that nothing is blocking the ventilation holes. 
(1 page 13)
Frequency is out of range!cFrequency is out of range. Input a signal that is within the 
acceptable frequency range of the projector. (1 page 76)
Please check Input-A 
Signal Sel.cSet “Input-A Signal Sel.” in the Setup   menu to 
“Computer” when an RGB signal is input from a computer. 
(1 page 54)
Please replace the Lamp/
Filter.cIt is time to replace the lamp. Replace the lamp. (1 page 69)
cAlso, replace the air filter too. Restart cleaning the ventilation 
holes (intake). (1 page 69)
If this message appears again after you replace the lamp and 
filter, the lamp replacement process is not complete. Check the 
lamp replacement process. (1 page 69)
To clear this message, press any button either on the remote control 
or the control panel of the projector once. Symptom Cause and Remedy
Note 
						

							 68
Caution messages
Please clean the filter.cIt is time to clean the air filter. Clean the air filter. (1 page 72)
To clear this message, press any button either on the remote control 
or the control panel of the projector once.
Please clean the filter. Have 
you finished? Yes NocIt is time to clean the air filter. Clean the air filter. (1 page 72)
cIf you cleaned the air filter, select “Yes.” If you did not clean the 
air filter, select “No.”
Projector temperature is 
high.  Cooling Setting 
should be “High”  if 
projector is being used at 
high altitude.cCheck to ensure that the ventilation holes on the unit are not 
covered. (1 page 13)
cWhen using the projector at high altitude, set the “Cooling 
Setting” to “High”. (1 page 53)
When temperature inside the projector remains high, the “Cooling 
Setting” is switched to “High” in 1 minute, then the fan speed 
increases.
Message Cause and Remedy
 cNo signal is input in the selected input. Check connections. 
(1 page 18)
Not applicable!cPress the appropriate button.
cThe operation to be activated by the button is currently 
prohibited. Message Cause and Remedy
Note
Note
x 
						

							69 
Others
Replacing the Lamp 
and the Air Filter and 
Cleaning the 
Ventilation Holes 
(intake)
Tools you need to get started:
 Projector Lamp LMP-H201 (Optional)
Standard Phillips screwdriver
Cloth (for scratch protection)
The lamp used for the light source has a 
certain lifespan. When the lamp dims, the 
color balance of the picture becomes strange, 
or “Please replace the Lamp/Filter.” appears 
on the screen, the lamp may be exhausted. 
Replace the lamp with a new one (not 
supplied) 
without delay.
Use an LMP-H201 Projector Lamp as the 
replacement lamp.
The air filter is supplied with the LMP-H201 
Projector Lamp. When you replace the lamp, 
it is also time to replace the air filter.
Whenever you replace the lamp, be sure to 
replace the air filter with a new one. Also 
clean the ventilation holes (intake).
 The lamp remains hot after the projector is 
turned off with the ?/1 (ON/STANDBY) 
switch. If you touch the lamp, you may burn 
your fingers. When you replace the lamp, 
wait for at least 1 hour for the lamp to cool.
 Do not touch the surface of the lens. If you 
touch it, wipe off the fingerprints with a 
soft cloth.
 Pay special attention to replacing the lamp 
when the projector is installed on the ceiling.
 When removing the lamp unit, make sure it 
remains horizontal, then pull straight up. Do 
not tilt the lamp unit. If you pull out the lamp 
unit while tilted and if the lamp breaks, the 
pieces may scatter, causing injury.
 When you remove the air filter, be careful 
not to let any dust fall into the projector.
 Replacing the air filter is crucial to maintain 
the good performance of the projector or to 
prevent malfunction to it. When a warning message for replacing the air filter appears, 
replace the air filter immediately.
1Turn off the projector and unplug 
the AC power cord.
2When setting the projector on a 
flat surface such as a desk etc., 
put a cloth to prevent the surface 
from being scratched. Reverse 
the projector as illustrated, then 
place it on the cloth.
 When the lamp is damaged the broken 
pieces of the lamp may become 
scattered, if you do not reverse the 
projector. This may cause injury.
 Be sure that the projector is placed on a 
stable surface.
Caution
Notes 
						

							 70
3Loosen the screw on the lamp 
cover with a Philips screwdriver, 
and then open the lamp cover.
4Loosen the 3 screws on the 
lamp with the Phillips 
screwdriver. Hold up the handle, 
then pull the lamp straight out.
5Hold the handle of the new lamp 
and push it in securely until it 
reaches the end, and then 
tighten the 3 screws.
Be careful not to touch the optical block 
inside the unit.
6Close the lamp cover, then 
tighten the screws.
Note