Stiga Lawn Mower MULTICLIP 50 EL 71503913 0 Operators Manual

							9
Obs: Håll strömkabeln på säkert avstånd från klingan.
Huomio: Virransyöttöjohtoa ei saa pitää terän läheisyy-
dessä.
Vigtigt:Hold strømkablet på sikker afstand fra klingen.
Obs:Hold strømkablen på sikker avstand fra kniven.
Achtung:Anschlußkabel von den Schneidwerkzeugen
fernhalten.
Important: keep the power supply cable away from the
blade.
Attention:maintenir le câble d’alimentation éloigné de la
lame.
Waarschuwing:houd de voedingskabel uit de buurt van
het maaiblad.
Attenzione:tenere il cavo di alimentazione lontano dalla
lama.
Atención: Tener el cable eléctrico de alimentacion lejos
de la cuchilla.
Cuidado: Manter o cabo eléctrico de alimentaçao longe
de lâmina.
Uwaga:Trzymać kabel zasilający daleko od noży.
Uzman¥bu:nodrošiniet, lai elektr¥bas vads atrastos tÇlu no
asmens.
Dòmesio:maitinimo laidà laikykite toli nuo ašmen .
Ç ÇÌ
ÌË
ËÏ
χ
‡Ì
ÌË
ËÂ
Â:
: 
 
ÑÂÊËÚ ͇·Âθ ÔËÚ‡ÌËfl ‚‰‡ÎË ÓÚ ÌÓʇ.
Pozor: Dbejte, aby kabel byl vždy v bezpečné vzdálenosti
od nože.
Pozor:Dovodni kabel naj bo daleč od rezila.
4
Se upp med de skarpa bladen: koppla ur matarkabeln
innan man fortsätter med underhåll eller om sladden är
trasig.
Varo leikkaavia teriä: Irrota laite sähköverkosta aina
ennen huoltotoimenpiteiden aloittamista tai jos johto on
viallinen.
Pas på: knivene er skarpe. Tag stikket ud af kontakten,
inden der udføres vedligeholdelse eller hvis kablet er
defekt.
Pass på knivblad i bevegelse: Ta stikkontakten ut av
støpselet før vedlikehold eller hvis ledningen er ødelagt. 
Achten Sie auf die scharfen Messer: Den Netzstecker
ausziehen bevor man mit der Wartung beginnt oder wenn
das Kabel beschädigt ist.
Beware of sharp blades:Remove plug from mains before
maintenance or if cord is damaged.
Attention aux lames coupantes:Ôter la fiche de
l’alimentation avant de procéder à l’entretien, et si le câble
est endommagé.
Opgelet voor op de scherpe messen:haal de stekker uit
het stopcontact vóór elke onderhoudsbeurt en indien de
voedingskabel beschadigd werd.
Attenzione alle lame taglienti:Togliere la spina dall’ali-
mentazione prima di procedere alla manutenzione o se il
cavo è danneggiato.
Atención con las cuchillas cortadoras: Desconectar el
cable de la alimentación antes de efectuar cualquier
operación de manutención o si el cable estuviera dañado. 
Atenção às lâminas afiadas:Remover a ficha da alimen-
tação antes de efectuar a manutenção ou se o cabo esti-
ver estragado.
Uważać na tnące ostrza: Odłączyć przewód zasilania
przed przystąpieniem do konserwacji lub jeśli kabel jest
uszkodzony. 
Pievïrsiet uzman¥bu griešanas asme¿iem:Izvelciet
kontaktdakšu pirms apkopes darbu veikšanas vai ja vads
ir bojÇts.
Aštri  ašmen  pavojus:prieš atlikdami priežiros darbus
arba jeigu pažeistas laidas iš maitinimo lizdo ištraukite
kištukà.
é éÒ
ÒÚ
ÚÓ
Ó
Ó
ÓÊ
ÊÌ
ÌÓ
Ó,
, 
 Ó
ÓÒ
ÒÚ
Ú
˚
˚Â
 
 Ì
ÌÓ
ÓÊ
ÊË
Ë!
! 
 
èÂ‰ ‚˚ÔÓÎÌÂÌËÂÏ Í‡ÍËı-
ÎË·Ó ÓÔÂ‡ˆËÈ ÔÓ ÚÂıÓ·ÒÎÛÊË‚‡Ì˲ ËÎË ‚ ÒÎÛ˜‡Â
ÔÓ‚ÂʉÂÌËfl ͇·ÂÎfl ÓÚÒÓ‰ËÌËÚ ‚ËÎÍÛ ÓÚ ËÒÚÓ˜ÌË͇
ÔËÚ‡ÌËfl.
Pozor na řezající nože. Před vykonáním jakékoli údržby
nebo je-li kabel poškozený, odpojte zástrčku od napájecí
sítě.
Pazite na ostra rezila: Preden začnete z vzdrževalnimi
posegi, ali v primeru poškodovnega kabla, izvlecite vedno
vtikač iz električnega omrežja.
3
CG rsb MCSe/Sti 71503913/0   23-01-2006  17:30  Pagina 9 
						

							20
SAFETY REGULATIONSTO BE FOLLOWED CAREFULLY
1) Read the instructions carefully. Get familiar with the con-
trols and the proper use of the equipment. Learn how to
stop the engine quickly.
2) Only use the lawnmower for the purpose for which it was
designed, i.e. for cutting grass. Any other use can be haz-
ardous, causing injury or damage to people and/or proper-
ty.
3) Never allow children or people unfamiliar with these
instructions to use the lawnmower. Local regulations may
restrict the age of the operator.
4) Never use the lawnmower:
– When people, especially children, or pets are nearby;
– If the operator has taken medicine or substances that can
affect his ability to react and concentrate.
5) Remember that the operator or user is responsible for
accidents or hazards occurring to other people or their
property.
1) While mowing, always wear sturdy footwear and long
trousers. Do not operate the equipment when barefoot or
wearing open sandals.
2) Thoroughly inspect the area where the equipment is to
be used and remove all objects which may be thrown by
the machine or damage the cutter assembly and the engine
(stones, sticks, metal wire, bones, etc.).
3) Before use, always inspect the machine, especially the
condition of the blades, and check that the screws and cut-
ting assembly are not worn or damaged. Replace worn or
damaged blades and screws in sets to preserve balance.
4) WARNING: DANGER! Damp and electricity do not go
together:
– cables must be handled and wired when dry
– never allow contact between an electric socket or cable
with a wet area (puddles or damp grass);
– connections between cables and sockets must be of the
waterproof type. Only use extension cables with moulded-
on waterproof or approved sockets available commercial-
ly.
– power the machine using a residual current device (RCD
Residual Current Device) with max. 30 mA tripping current.
5) The power supply cables must not be of lower quality
than the H05RN-F or H05VV-F type with minimum cross-
section size of 1.5 mm
2and max. 25 m long.
6) Attach the cable onto the cable clamp before starting the
machine.
7) The permanent wiring of any electrical device to the
mains must be carried out by a qualified electrician, in
accordance with electrical regulations in force. Incorrect
wiring may cause severe injury or death.
1) Mow only in daylight or good artificial light.
2) Avoid operating the equipment on wet grass or in the
rain.
3) Never go over the electric cable with the lawnmower.
While cutting, the cable should always be pulled behind the
lawnmower and always from the area of grass already cut.
Use the cable clamp as described in this manual to prevent
the cable from disconnecting by accident. Ensure that it is
properly inserted without forcing into the power socket.
4) Never pull the lawnmower by its power cable or pull the
cable to remove the plug. Do not expose the cable to
sources of heat or let it come in contact with oil, solvents
or sharp objects.
5) Always be sure of your footing on slopes.
6) Walk, never run and do not allow yourself to be pulled
along by the lawnmower.
7) Mow across the face of slopes, never up and down.
C) OPERATION 
B) PREPARATION
A) TRAINING
EN8) Exercise extreme caution when changing direction on
slopes.
9) Do not mow on slopes that are too steep.
10) Exercise extreme caution when pulling the lawnmower
towards you.
11) Stop the blade if the lawnmower has to be tilted for
transportation when crossing surfaces other than grass,
and when transporting the lawnmower to and from the area
to be mowed.
12) Never operate the lawnmower with defective guards.
13) On power-driven models, disengage the drive clutch
before starting the engine.
14) Start the engine carefully, following the instructions and
keeping feet well away from the blade. 
15) Do not tilt the lawnmower when switching on the
engine unless it is strictly necessary for start-up. In this
case, do not tilt it more than is strictly necessary and only
lift the part furthest away from the operator. Check that
both hands are positioned correctly before lowering the
lawnmower.
16) Do not put hands or feet near or under rotating parts.
Keep clear of the discharge opening at all times.
17) Never pick up or carry a lawnmower while the engine is
running.
18) Stop the engine and disconnect the power supply
cable:
– before carrying out any work underneath the cutting
deck;
– before checking, cleaning or working on lawnmower;
– after striking a foreign object. Inspect the lawnmower for
damage and make repairs before restarting and operating
the lawnmower;
– if the lawnmower starts to vibrate abnormally, find and
remove the cause of the vibration immediately;
– whenever you leave the lawnmower unattended.
– when transporting the equipment.
19) Stop the engine:
– before adjusting the grass cutting height.
20) When mowing, always keep to a safe distance from the
rotating blade. This distance is the length of the handle.
1) Keep all nuts, bolts and screws tight to be sure the
equipment is in safe working condition. Regular mainte-
nance is essential for safety and performance.
2) To reduce the fire hazard, keep the lawnmower, espe-
cially the engine, free of grass, leaves, or excessive grease.
Do not leave containers with grass cuttings in rooms.
3) Periodically check the electric cables and replace them
if they are damaged or if the insulation has been damaged.
Never touch a badly insulated cable if it still connected to
the power supply. Remove the cable from the socket
before taking any action.
4) Wear strong work gloves when removing and reassem-
bling the blade.
5) Keep the blade balanced during sharpening. All opera-
tions on the blade (dismantling, sharpening, balancing,
remounting and/or replacing) require a certain familiarity
and special tools. For safety reasons, these jobs are best
carried out at a specialized centre.
6) For reasons of safety, do not use the equipment with
worn cables or damaged parts. Parts are to be replaced
and not repaired. Use genuine spare parts (blades should
always bear the symbol  ). Parts that are not of the same
quality can damage the equipment and be dangerous for
your safety.
1) Whenever the machine is to be handled, raised, trans-
ported or tilted you must:
– wear strong working gloves;
– grasp the machine at the points that offer a safe grip, tak-
ing account of the weight and its distribution.
– use an appropriate number of people for the weight of the
machine and the characteristics of the vehicle or the place
where it has to be placed or collected.
E) TRANSPORTATION AND HANDLING
D) MAINTENANCE AND STORAGE
CG rsb MCSe/Sti 71503913/0   23-01-2006  17:30  Pagina 20 
						

							21
STANDARDS OF USE
NOTE – The machine can be supplied with some of the
components already fitted.
Return the lower part of the pre-fitted handle (1) to
its working position and lock into place using the lower
knobs (2).
Attach the upper part (3) using the screws (4) supplied.
Fit the cable clamps (5) as shown. The correct position for
the cable hook (6) is as shown.
The engine is controlled by a dual action switch to
prevent starting it accidentally. To start, press the button (2)
and pull the lever (1).  The engine automatically stops when
the lever (1) is released.
The cutting height is adjusted using the levers (1). 
The four wheels must be at the same height.  
MAKE THIS ADJUSTMENT ONLY WHEN THE BLADE IS
STOPPED.
Connect the extension cable correctly as indicated.
Start the engine by pressing the safety push-button (2) and
pulling the switchgear lever (1).
While cutting, ensure that the electric cable is
always behind you and on the area of grass already cut.
The lawn will look better if it is always cut to the same
height and in alternate directions.
A machine with MULCHING system cuts the grass, chops
it finely and then blows it down in the lawn. The grass clip-
pings need not to be collected.
The following rules should be observed to give best
MULCHING effect:
1. Do not cut the grass too short. Not more than 1/3rd of
the length should be cut off.
2. Always keep it clean under the mower casing.
3. Always use a well sharpened blade.
4. Avoid mowing when the grass is wet. The grass then
sticks to the underside of the casing, giving poor mow-
ing results.
3.2
3.1
3. GRASS CUTTING
2.2
2.1
2. DESCRIPTION OF CONTROLS
1.1
1. FINISH ASSEMBLY
ENWhen you have finishing mowing, release the lever
(1). FIRST disconnect the cable extension from the supply
socket (2) and THEN from the side of the lawnmower’s
switchgear (3). WAIT FOR THE BLADE TO STOP before
carrying out any type of work on the machine.
IMPORTANT NOTE
Should the motor stop during use through overheating,
wait about 5 minutes before re-starting.
IMPORTANT – Regular, careful maintenance is essen-
tial for keeping the safety level and original perform-
ance of the machine unchanged in time.
Store the lawnmower in a dry place.
1) Wear strong working gloves during any cleaning, main-
tenance or adjustment operation on the machine.
2) Remove the grass debris after each cut and mud accu-
mulated inside the chassis to avoid their drying and thus
making the next start-up difficult.
3) The paintwork on the inside of the chassis may peel off
in time due to the abrasive action of the cut grass; in this
case, intervene promptly by touching up the paintwork
using a rustproof paint to prevent the formation of rust
that would lead to corrosion of the metal.
All operations on the blade should be carried out at
a specialized centre.
Note for specialized centres: Reassemble the blade (2) as
shown in the drawing and tighten the central screw (1)
using a torque wrench set to 16-20 Nm.
Do not use forced water and avoid wetting the
motor or the electrical components
Should you have any doubts or problems, do not hesitate
to contact your nearest Service Centre or your Dealer.
4.2
4.1
4. ROUTINE MAINTENANCE
3.3
CG rsb MCSe/Sti 71503913/0   23-01-2006  17:30  Pagina 21 
						

							Manufactured by:
GGP ITALY SPA  •  Via del lavoro, 6  •  I-31033 Castelfranco Veneto (TV) - ITALY
CG rsb MCSe/Sti 71503913/0   23-01-2006  17:30  Pagina 4 
						

							71503913/0
www.stiga.com
GGP Sweden AB - Box 1006 - SE-573 28 TRANAS
LWA
(Year) . . . . . . . S/N° . . . . . . . . . . . . . . . .
dB
Model: . . . . . . . . . . . . . . . .
Type: . . . . . . . . . . .
✍
CG rsb MCSe/Sti 71503913/0   23-01-2006  17:30  Pagina 1