Stiga Lawn Mower PARK 2WD 110 Combi Pro 125 Combi Pro Instruction Manual

							
STIGA PARK
2WD
110 Combi Pro
125 Combi Pro
8211-0546-03 
						

							2
1
2
A
B C
3
5 
7 1
4 
6 
82 
						

							3
1/3
24 Nm
D
11
13 9 
12 10  
						

							19
ENGLISHEN
1 GENERAL
This symbol indicates WARNING. Seri-
ous personal injury and/or damage to 
property may result if the instructions 
are not followed carefully.
You must read these instructions for use 
and the machine’s safety instructions 
carefully.
1.1 SymbolsThe following symbols appear on the machine. 
They are there to remind you of the care and atten-
tion required in use.
This is what the symbols mean:
Warning!
Read the instruction manual and the safety 
manual before using the machine.
Warning!
Do not insert your hands or feet under the 
cover when the machine is in operation.
Warning!
Watch out for discarded objects. Keep on-
lookers away.
Warning!
Before starting repair work, remove the 
spark plug cable from the spark plug.
1.2 References
1.2.1 Figures
The figures in these instructions for use are num-
bered 1, 2, 3, etc. 
Components shown in the figures are marked A, B, 
C, etc.
A reference to component E in figure 5 is written 
“5:E”.
1.2.2 Headings
The headings in these instructions for use are num-
bered in accordance with the following example:
“2.3.2” is a subheading to “2.3” and is included un-
der this heading.
When referring to headings, only the number of the 
heading is normally specified. E.g. “See 2.3.2”.
2 DESCRIPTION
2.1 GeneralThe cutting deck is intended for use on Stiga’s 2-
wheel drive Park machines. 
The cutting deck is supplied in one of the follow-
ing versions:
• With manual adjustment of cutting height.
• With electrical adjustment of cutting height.
2.2 Controls, 125 Combi Pro
2.2.1 Cutting height adjustment
The cutting height can be adjusted between 25 and 
90 mm. 
Electrical cutting height adjustment
The setting can be adjusted infinitely variably us-
ing a switch on the machine.
Manual cutting height adjustment
The setting can be adjusted to a number of fixed 
positions using the lever. See fig. 1.
2.2.2 Incline forwards
The rear section of the cutting deck can be raised 
12 mm by moving the two pins down one hole 
from the basic setting. See fig. 2.
2.2.3 Rear mounting
The cutting deck’s rear section is secured with the 
pins in fig. 2.
2.2.4 Mounting in implement lifter
The deck is mounted in the implement lifter with a 
chain and snap hooks. 
One snap hook is intended for the working position 
and can be moved in the chain links to set the lift-
ing force.
The other snap hook is intended for the washing 
position.
3 ASSEMBLY 
3.1 Installing1. Place the cutting deck in position in front of the 
machine.
2. Install the deck mounts on the machine’s steer-
ing knuckles. See fig. 3.
3. Remove the pins and the washers on both sides. 
See fig. 2.
4. Screw the arms into each other. See fig. 4.
5. Suspend the cutting deck in the implement lift-
er. See fig. 5.
6. If the deck has electrical cutting height adjust-
ment, connect the cable to the machine’s front 
right socket. See fig. 7. 
						

							20
ENGLISHEN
3.2 BeltThe cutting deck’s rear section should rest on the 
floor (it should not be lifted or secured).
Install the belt as follows:
1. Set the maximum cutting height.
2. Locate the belt around the machine’s belt pulley 
(8:B).
3. Tension the belt with the belt idler (8:A)B. The 
belt idler should be on the left side of the belt 
viewed from the driver’s position. 
4. Lift up and secure the rear section of the cutting 
deck.
On machines with 17” wheels:
 Install the wash-
ers and the pins in the top hole. See fig. 2.
On machines with 16” wheels:
 Install the wash-
ers and the pins in the middle hole. See fig. 2.
3.3 Tyre pressureAdjust the air pressure in the tyres as follows:
Front: 0.6 bar (9 psi).
Rear: 0.4 bar (6 psi). 
4 USING THE MACHINE
Check that the grass that is to be cut is 
completely free of foreign objects such 
as stones etc.
4.1 Cutting heightThe best cutting results are achieved when the 
when the top third of the grass is cut off. I.e. 2/3 of 
the length of the grass remains. See fig. 9.
If the grass is long and has to be cut significantly, 
cut twice using different cutting heights.
Do not use the lowest cutting heights if the lawn 
surface is uneven. This would entail a risk of the 
blades being damaged against the surface and the 
lawn’s top layer of soil being removed.
4.2 InclineThe cutting deck’s rear section can be lifted so that 
the deck has a greater forward incline than that 
provided by the basic setting. This incline affects 
the cutting results as follows.
4.2.1 No incline
When the deck is in the basic setting, the best 
mulching effect and good dispersion of the cut 
grass are achieved. The basic setting is recom-
mended for normal grass.
4.2.2 Incline
When the cutting deck is inclined forwards, the 
mulching effect is reduced while the cut grass is 
dispersed better.
Inclining forwards is recommended for thicker 
grass.
4.3 Mowing adviceIn order to achieve optimum mowing results, fol-
low the advice below:
• Cut frequently.
• Run the engine at full throttle.
• The grass should be dry.
• Use sharp blades.
• Keep the underside of the cutting deck clean.
125 Combi Pro can cut the grass in the following 
two ways:
• Mulching: composting and spreading.
• Rear ejection: ejects the grass in a line behind 
the deck.
The deck is set for mulching on delivery. In order 
to eject the grass in a line behind the deck, the plug 
in fig. 6 must be removed. 
Set the deck in service position (see 5.3) in order to 
remove/install the plug.
5 MAINTENANCE
5.1 PreparationAll service and all maintenance must be carried out 
on a stationary machine with the engine switched 
off.
Prevent the machine from rolling by al-
ways applying the parking brake.
Stop the engine.
Prevent unintentional starting of the 
engine by disconnecting the spark plug 
cable from the spark plug and remov-
ing the ignition key. 
5.2 Washing position1. Activate the parking brake.
2. Set the implement lifter in transport position.
3. Set the highest cutting height.
4. Remove pins and washers. See fig. 2.
5. Grip the front edge of the deck and lift up. Hook 
on the chain so that the deck is pointing diago-
nally upwards. See fig. 10.
It is absolutely forbidden to start the engine 
when the deck is in the washing position.
Reset in accordance with 3.2, point 4. 
						

							21
ENGLISHEN
5.3 Service position1. Activate the parking brake.
2. Set the implement lifter in transport position.
3. Set the highest cutting height.
4. If the deck has electrical cutting height adjust-
ment, disconnect the cable from the machine. 
See fig. 7.
5. Remove pins and washers. See fig. 2.
6. Hook the belt idler arm on the mount (8:C)
7. Force the belt off the centre pulley (8:B). 
8. Grip the front edge of the deck and lift up. Lift 
until the deck is completely vertical and rest the 
rear edge on the floor. See fig. 11.
Reset in accordance with 3.1.
5.4 CleaningThe underside of the deck must be cleaned after 
each use. 
Set the deck in washing position. 
Clean the underside of the deck carefully. Use a 
high-pressure washer, scraper and/or brush.
When the surfaces are completely dry and clean, 
touch up the paintwork. Use durable yellow paint 
intended for metal outdoors.
5.5 Wheels125 Combi Pro is fitted with two lubricating cups 
(12:D) for the vertical shafts.
The grease nipples must be lubricated with univer-
sal grease after 50 hours of operation.
5.6 Replacing blades, fig. 13
Wear protective gloves when changing 
blade(s) to avoid cutting yourself.
Check that the blades are always sharp. 
This produces the best cutting results. 
Always check the blade(s) after a collision. If the 
blade system has been damaged, defective parts 
should be replaced.
Always use genuine spare parts. Non-
genuine spare parts can entail a risk of 
injury, even if they fit the machine.
The full blade is replaced when the edges 
are worn.
Install the new blade with the punched text facing 
down.
Tightening torque: 24 Nm
5.7 Wear protectionThere are two wear protection devices on the un-
derside of the cutting deck to protect it. These can 
be replaced if necessary.
6 SPARE PARTS
STIGA genuine spare parts and accessories are de-
signed specifically for STIGA machines. Please 
note that ‘non-genuine’ spare parts and accessories 
have not been checked or approved by STIGA:
The use of such parts and accessories 
can affect the function and safety of the 
machine. STIGA accepts no responsi-
bility for damage or injuries caused by 
such products.
7 DESIGN REGISTRATION
This product or parts thereof is covered by the fol-
lowing design registration:
Sweden: 66 166
Germany: 499 11 740.9
France: 577 251-253, 577 439-443
USA: 435 564
GGP reserves the right to make alterations to the 
product without prior notification. 
						

							www.stiga.com
GGP Sweden AB · Box 1006 · SE-573 28 TRANÅS