Surefire 318fg, 618fg Tactical Light User Manual

							Model 318FG
618FG
Tactical Light
Users Manual
Remington 870
12 Gauge Shotgun
Revision A    9-1-95 
						

							Model 318FG 618FG Tactical Light
Introduction
   The Model 318FG & 618FG Tactical light provides a rugged and reliable source of high
intensity light that is integrated into the fore-arm of the shotgun. The lamp is shock isolated.
There are three switches built into the H18FG Housing. A two button ON/OFF switch on the
left side, wired in parallel, provides the means to turn the light ON and have it stay ON until it
is turned OFF. A two button ON/OFF switch and a Pressure Switch are located on the right
side and wired in series. When the ON/OFF switch is ON the Pressure Switch will turn the
light ON when pressure is applied to the switch and OFF when pressure is released. When
the ON/OFF switch is OFF, the Pressure Switch is deactivated. A Switch Blocker is provided
for users that want to reduce the functional size of the Pressure Switch.
Installation
1. Put safety on safe. Open action and make certain no shells remain in chamber or magazine.
    Close action and remove Magazine Cap and Barrel. Reach into bottom of receiver and
    press left shell latch inward. Slide Fore-End Tube off Magazine Tube.
    NOTE: Top right edge of slide may bind on bottom front of ejection port in receiver.
    To free slide, push front end of bolt downward.
2. Unscrew and remove Fore-End Tube Nut using Installation Tool supplied in kit and remove
    wooden Fore-End by pulling it straight off the Fore-End Tube.
3. Place H18FG Housing onto the Fore-End Tube and reinstall Fore-End Tube Nut using
    Installation Tool.
4. Install Fore-End Tube on receiver by placing slide and breech bolt on the end of the
    Fore-End Action Bars. Insert the end of Action Bars into matching grooves in the Receiver.
    Move Fore-End gently rearward into receiver until contact is made with front end of right
    shell latch. Press front of right shell latch into side of receiver. Move Fore-End past right
    shell latch until contact is made with left shell latch. Press front of left shell latch inward to
    allow Fore-End Tube to pass and reassemble freely into receiver. Reassemble Barrel and
    tighten firmly with magazine cap.
5. Install Battery into the Housing with the + contact facing out.
6. Screw Lamp Housing into H18FG Housing.
7. Test the light using the switches, the light should come on. Installation is now complete.
Kit Contents
! H18FG Housing
! L30 or L60 Lamp Module
! DL123A or DL223AC Battery
! Installation Tool
! Model Z10 Switch Blocker
! Alcohol  Wipe
! Users Manual 
						

							Model 318FG 618FG Tactical Light
Lamp Replacement
1. Unscrew Bezel from Lamp Housing. Lift Lamp assembly out of Bezel.
2. Install replacement Lamp Assembly in Bezel and reassemble by
    screwing onto Lamp Housing until it is fully seated.
Battery Replacement
1. Unscrew Lamp Housing from H18FG Housing and shake out old battery.
2. Install new battery with the + terminal facing out.
3. Reinstall Lamp Module.
Switch Blocker Installation
   If you want to disable the part of the pressure switch where you rest your hand, (and don’t
want the light to come on) you can cover it with the Model Z10 Switch Blocker. First clean the
portion of the Pressure Switch to be disabled using the Alcohol Wipe from the Kit. Then
remove the paper backing from the underside of the Switch Blocker and press the Switch
Blocker in place on the Pressure Switch.
WARNING
Lithium batteries can explode or cause burns if disas-
sembled, shorted, recharged or exposed to fire or high
temperatures.  Please handle with care. 
						

							Sure-Fire LLC 
						

							Caution
   The battery used in the light is very powerful. Be sure that the switch is not touching anything
when the light is stored. If the lamp is turned on while in a case or other container, the lamp can
overheat and damage the light or surrounding materials. Remove the battery or unscrew the bezel
far enough to prevent the lamp from turning on when stored.
   Do not use a 3 Volt Lamp in a 6 Volt system. The lamp will BURN OUT immediately!!! To
identify a lamp assembly: the 3 volt lamp has a Red label and is marked R30, the 6 volt has a Blue
or Green label and is marked R60 or P60.
   If it is necessary to dispose of any batteries, do not do so by fire, mutilation or by disassembly,
as this may cause toxic chemicals to be released.
Model 318F 618F Tactical Light
Repairs & Replacements
     To obtain repair or replacement call Customer Service at 800-828-8809 (toll free) or 714-545-
9444 and obtain a Return Authorization number (RA). Then pack the unit carefully and return (no
COD’s please) to:
     Sure-Fire LLC
     Repairs Department, RA ____
     18300 Mt. Baldy Circle
     Fountain Valley, CA 92708
Sure-Fire LLC will pay any reasonable shipping costs to return the unit to you.
Warranty
     Sure-Fire LLC warrants that its products will be free from defects in materials and workmanship.
Sure-Fire LLC will repair or replace (at its option), without charge, any product or part which is
found to be defective under normal use and service. Such repair or replacement shall be the
purchaser’s sole and exclusive remedy under this warranty. This warranty does not include normal
maintenance and services and does not apply to any products or parts which have been subject to
modification, misuse, negligence, accident, improper maintenance or repair by anyone other than
Sure-Fire LLC.
“Fine Print” Warranty Limitation
     There is no other express warranty.  Sure-Fire LLC hereby disclaims any and all implied
warranties, including, but not limited to fitness for a particular purpose.  Sure-Fire LLC shall not be
liable for incidental, consequential, or special damages arising out of, or in connection with product
use or performance.
um_H18FG_5.901
71-01-448