Tenda Router W330R User Manual

 Wireless-N Broadband Router   
Hardware Installation 
 
1. Please connect the LAN 
port of the router to the 
network adapter of your 
computer with one cable.  
 
 
 
 
2.Please use the delivery- 
attached power adapter to 
power the router. 
  
 
 
 
3.Please connect your 
broadband line provided 
by your ISP to the WAN 
port of your router. 
 
 
 
 
 
 
 
 
IMPORTANT:  
Please use the included power adapter. Use of a 
different power adapter could cause damage and 
void the warranty for this...

 Wireless-N Broadband Router   
Chapter 3: Getting to Connect the 
Wireless-N Broadband Router   
 
For easy and fast configuration, the following steps for 
network configuration are required.     
 
How to Set the Network Configurations for My 
Computer  
 
Right click “ My Network 
Places ” and select 
“Properties ”.   
 
 
 
 
 
 
Right click “ Local Area 
Network Connection ” 
and select “ Properties”.   
 
 
 
Select “Internet Protocol 
(TCP/IP) ”and click 
“Properties ”. 
 
 
 
 
 
  7 

 Wireless-N Broadband Router   
Select “Obtain an IP 
address automatically ” 
and “ Obtain DNS server 
address automatically ”. 
Click “ OK” to save the 
configurations. 
 
 
 
Or  select “ Use the 
following IP address ” 
and enter the IP address, 
Subnet mask, Default 
gateway as shown right. 
Of course, you need to 
input the DNS server 
address provided by your 
ISP. Otherwise, you can 
use the Router’s default 
gateway as the DNS proxy 
server. Click “ OK” to save 
the configurations....

 Wireless-N Broadband Router   
How to Check the Network Connection 
 
Select“Start”— ”Program
s ”—“ Accessories ” 
—“Command Prompt ”.  
 
 
 
 
 
Input the “ping 
192.168.0.1 ” and press 
“Enter ”. If the screen 
displays as the right figure, 
it means your PC is 
connected to your router 
successfully.  
 
If not, please make sure 
the hardware installation 
and network adapter are 
OK. After all preparations 
are made,  please proceed 
to Chapter 4 for more and 
advanced configuration....

 Wireless-N Broadband Router   
Chapter 4 Basic Configurations 
 
This section is to show you how to configure your new 
Wireless-N Broadband Router through the Web-based 
Configuration Utility. 
 
How to Access the Web-based Configuration 
Utility 
 
To access the Router’s 
Web-based Utility, launch a 
web browser such as 
Internet Explorer or Firefox 
and enter the Router’s 
default IP address, 
http://192.168.0.1. Press 
“Enter”.   
Please input the “ admin” in 
both User Name and 
Password. Click “...

 Wireless-N Broadband Router   
Setup Wizard  
 
Here is the “Welcome to 
Setup Wizard ” for 
configuring your Router 
quickly. Click “ Next”.  
In this screen, select one 
mode of your Internet 
connection you use. If you 
are not clear, press the 
“Detect ” button or contact 
your Internet Service 
Provider, and click “ Next”.  
 
 
 
 
ÎConnection Mode 1 : 
ADSL Virtual Dial-up (Via 
PPPoE) 
 
Enter the Account and 
Password provided by 
your ISP, and click 
“Next ”.  
 
ÎConnection Mode 2 : 
Dynamic...

 Wireless-N Broadband Router   
is Dynamic IP, it means 
your IP address keeps 
changing every time you 
connect. You do not need 
to enter the information 
like Mode 2 or Mode 3. 
ÎConnection Mode 3: 
Static IP  
 
In this screen, fill the 
network address  
information from your ISP 
in the IP Address, Subnet 
Mask, Gateway and 
Primary DNS server 
fields and click “Next ”.  
 
ÎConnection Mode 4 : 
L2TP 
 
Select L2TP(Layer 2 
Tunneling Protocol) if 
your ISP use a L2TP 
connection, your ISP will...

 Wireless-N Broadband Router   
parameters. 
 
L2TP provides two 
access modes. 
 
If the L2TP offered by 
your ISP is Dynamic IP: 
Please select Dynamic 
IP . 
If the L2TP offered by 
your ISP is Static IP : 
Please fill in the 
parameters provided by 
your ISP. 
After configuration, please 
click “Next”. 
ÎConnection Mode 5 : 
PPTP 
 
If the connection is “PPP 
Tunneling Protocol”, 
please input the following 
parameters provided by 
your ISP: Server IP 
Address, User Name, 
and Password. 
 
  13 

 Wireless-N Broadband Router   
PPTP provides two 
access modes. 
 
If the PPTP offered by 
your ISP is Dynamic IP: 
Please select Dynamic 
IP. 
If the PPTP offered by 
your ISP is Static IP : 
Please fill in the 
parameters provided by 
your ISP. 
After configuration, please 
click “Next”. 
Click “ Apply”, select 
“Reboot ” in System Tools  
of the left menu and press 
the “ Reboot the router” 
button.  
It is rebooting now, please 
wait for a few 
minutes and  DO NOT 
power off it.    
 
 
 
 
14 

 Wireless-N Broadband Router   
Click the “System Status ” 
in the left menu of the 
Web-based Utility to find 
out the current network 
and system information. If 
the “Connection Status” is 
“Connected”, 
Congratulations you on 
completing the Router’s 
basic settings. You are on 
the Internet now. If you 
want to configure more, 
please proceed to the 
following explanations for 
Advanced Settings.   
 
 
 
 
 
 
 
 
 
 
 
15