TiE Businesscom Plus 24/36/64 Installation Manual

							    Console 
						

							Speakerphones
2.16Speakerphones, which can be installed in Standard
telephones, permit handsfree CO conversations. The
maximum number of speakerphones permitted in each
system is as follows:
5.FCC AND TELCO REQUIREMENTS
SystemMaximum
2412
3612
6424
5.01 Rules and regulations for the operation and
installation of telephone equipment have been
established by the Federal Communications Commission
(FCC). According to Part 68, “Connection of Terminal
Equipment to the Telephone Network” and its amendments,
several actions are required before and during the installation
of customer-provided telephone equipment. These actions
are listed and described in the following paragraphs.
3.SPECIFICATIONSNOTIFICATION TO TELCO
3.01Refer to Tables  l-2 and 1-3 for technical
specifications pertaining to the Businesscom Plus
24   systems.
4.SITE REQUIREMENTS
5.02 As owner of this telephone system, you must give the
following information to the operating telephone
company (telco) before connecting or disconnecting it:
(1) Sufficient notice of your intention to use privately owned
telephone equipment.
4.01 The KSU should be installed in a clean, dry, secure
location that prevents access by unauthorized
personnel. This location, as detailed in Section 5, should
comply with Bell Functional Product Class Criteria of
September 1978, in publication PUB 48002 as stated in
3.4.3.2, paragraph C-Indoors With Environmental Control.
The room must have adequate ventilation and have a
temperature range that does not exceed 32 to 113 degrees
F (0 to 45 degrees C) with a 10 to 95% noncondensing,
relative humidity.
 The particular lines to be used (telephone numbers
xxx-xxxx through xxx-xxxx).
(3) Model: Businesscom Plus 
FCC Registration Number: 
Ringer Equivalence: 
Registered Jack: 
NOTE: Have telco drop the  connectors within 25 feet
of the installation.
INCIDENCE OF HARM
4.02The installation site should provide ample room to
mount the KSU on the wall along with the necessary5.03If customer-provided equipment is causing harm to
the telephone network, the telephone company
connecting blocks and any ancillary equipment. The
installation site should not be located in areas subject to static
electricity (e.g., dry copiers), vibration (e.g., heavy
machinery), or in areas likely to be  (e.g., basement
level).
4.03The customer must provide a dedicated NEMA
 outlet with a    and a 15 Ampmust, whenever practical, notify the customer that service
may be temporarily discontinued. The 
 company
must also attempt to inform the customer before actually
disconnecting service. The telephone company must provide
customers with an opportunity to correct the problem and
must advise customers of their right to bring complaint
procedures before the FCC.
circuit. A separate earth ground is required in addition to the
third-wire ground on the AC circuit. If a music source or
optional external paging equipment is installed, it must be
connected to an AC circuit other than the system’s dedicated
AC line. ONLY THE POWER SUPPLY SHOULD BE
CONNECTED TO THE DEDICATED AC OUTLET. 
						

							Table SPECIFICATIONS,  PLUS 24
GENERAL SPECIFICATIONS
System Capacity:MAX. NO.System Capacity:MAX. NO.CO Lines8Speakerphones12Intercom Talkpaths6OPX Telephones12
Key Telephones24
ELECTRICAL SPECIFICATIONS
Power Requirements: (AC Supply Must Be Dedicated)
KSU/Power Supply Operating Range: 117 VAC 
 10%60 Hz  Hz
Power Dissipation:
 Supply Unit: 340 Watts  2.9 Amp
Grounding Requirements:1160 
KSU Ground lug, 14 AWG or larger copper wire to cold water pipe or known good earth ground
Cable Requirements:
Four conductor (two-pair twisted) station wire. 1000 feet (304.8 m) using 24 AWG. 1500 feet (457.2 m)
using 22 AWG.
Door Chime Box: 500 feet (152.4 m) using 24 AWG.
Console: 1000 feet (304.8 m) using 24 AWG or 
500 feet (152.4 m) if two consoles are used and one is
used as a BLF (Busy Lamp Field)
Background Music Specifications:
Input Impedance: 600 OHMS
Input Level: Nominal 250 
 Maximum Input: 1 Volt RMSLimit for Alarm Circuit:
Loop Resistance: 1000 OHMS Max.
Music On Hold Specifications: External  Paging  Specifications:
Input Impedance: 600 OHMS Output Impedance: 600 OHMS
Input Level: Nominal 250 
 Output Level: Nominal 250  Maximum Input: 1 Volt RMS Maximum Output: 400  RMS
MECHANICAL SPECIFICATIONS
Dimensions and Weights:
KSU:
Power Supply:
Executive/Key Telephone:
Door Chime Box:
DSS Console:16.8 in.
x 21.5 in. x 7.8 in.26.5 Ibs.
430.0 mmx 550.0 mm
x 200.0 mm12.0 kg
12.1 in.
x 14.2 in.
x 4.8 in.12.8 Ibs.
310.0 mmx 363.5 mm x 122.0 mm5.8 kg
3.1 in.
x 8.0 in. x 8.6 in.2.2 
80.0 mmx 205.0 mm x 221.0 mm1.0 kg
5.1 in.
x 3.9 in. x 1.4 in.0.4 131.0 mmx 99.0 mm x 35.0 mm0.2 kg
2.0 in
x 7.4 in. x 8.8 in.1.3 Ibs.
52.0 mmx 189.0 mm x 224.0 mm0.6 kg
ENVIRONMENTAL SPECIFICATIONS
Environmental Operating Conditions:
Temperature:
KSU and Telephones: 0 to 45 degrees C
Door Chime Box: -20 to 60 degrees C
Humidity: 10% to 95% noncondensing(32 to 113 degrees F)
( -4 to 140 degrees F) 
						

							Table 1-2SPECIFICATIONS,  PLUS 36
GENERAL SPECIFICATIONS
System Capacity:MAX. NO.System Capacity:MAX. NO.CO Lines12Speakerphones12
Intercom Talkpaths6OPX Telephones18
Stations 3 6
ELECTRICAL SPECIFICATIONS
Power Requirements: (AC Supply Must Be Dedicated)
 Supply Operating Range: 117 VAC  10%
Power Dissipation:60 Hz  Hz
 Supply Unit: 480 Watts  4.1 Amps
Grounding Requirements:1638 
KSU Ground lug, 14 AWG or larger copper wire to cold water pipe or known good earth ground
Cable Requirements:
Four conductor (two-pair twisted) station wire. 1000 feet (304.8 m) using 24 AWG. 1500 feet (457.2 m)
using 22 AWG.
Door Chime Box: 500 feet (152.4 m) using 24 AWG.
Console: 1000 feet (304.8 m) using 24 AWG or 500 feet (152.4 m) if two consoles are used and one 
IS
used as a BLF (Busy Lamp Field)
Background Music Specifications:
Input Impedance: 600 OHMS
Input Level: Nominal 250 
 Maximum Input: 1 Volt RMSLimit for Alarm Circuit:
Loop Resistance: 1000 OHMS Max.
Music On Hold Specifications:External Paging Specifications:
Input Impedance: 600 OHMS Output Impedance: 600 OHMS
Input Level: Nominal 250 
 Output Level: Nominal 250  
Maximum Input: 1 Volt RMS Maximum Output: 400  RMS
MECHANICAL SPECIFICATIONS
Dimensions and Weights:
KSU:
Power Supply:
Executive/Key Telephone:
Door Chime Box:
DSS Console:16.8 in.
x 21.5 in. x 7.8 in.33.9 Ibs.
430.0 mm
x 550.0 mm x 200.0 mm14.0 kg
12.1 in.
x 14.2 in. x 4.8 in.12.8 Ibs.
310.0 mm
x 363.5 mm x 122.0 mm5.8 kg
3.1 in.
x 8.0 in. x 8.6 in.2.2 Ibs.
80.0 mmx 205.0 mm x 221.0 mm1.0 kg
5.1 in.
x 3.9 in. x 1.4 in.0.4 Ibs.
131.0 mmx 99.0 mm x 35.0 mm0.2 k g
2.0 in.
x 7.4 in. x 8.8 in.1.3 Ibs.
52.0 mm
x 189.0 mmx 224.0 mm0.6 kg
ENVIRONMENTAL SPECIFICATIONS 
Environmental Operating Conditions:
Temperature:
KSU and Telephones: 0 to 45 degrees C
Door Chime Box: -20 to 60 degrees C
Humidity: 10% to 95% noncondensing(32 to 113 degrees F)
( -4 to 140 degrees F) 
						

							Table H-3 SPECIFICATIONS,  PLUS 64
GENERAL SPECIFICATIONS
System Capacity:MAX. NO.CO Lines 2 4
Intercom Talkpaths
6Stations64
System Capacity:
Speakerphones
OPX TelephonesMAX. NO.24
32
ELECTRICAL SPECIFICATIONS
Power Requirements: (AC Supply Must Be Dedicated)
KSU/Power Supply Operating Range: 117 VAC 
 10%
Power Dissipation:
60 Hz  Hz
 Supply Unit: 870 Watts  7.4 Amps
Grounding Requirements:2968 BTU/HI=.
KSU Ground lug, 14 AWG or larger copper wire to cold water pipe or known good earth ground
Cable Requirements:
Four conductor (two-pair twisted) station wire. 1000 feet (304.8 m) using 24 AWG. 1500 feet (457.2m) using 22 AWG.
Door Chime Box: 500 feet (152.4 m) using 24 AWG.Console: 1000 feet (304.8) using 24 AWG or 500 feet (152.4 m) if two consoles are used and one
is used as a BLF (Busy Lamp Field)
Background Music Specifications:
Input Impedance: 600 OHMSInput Level: Nominal 250  Maximum Input: 1 Volt RMSLimit for Alarm Circuit:
Loop Resistance: 1000 OHMS Max.
Music On Hold Specifications:
Input Impedance: 600 OHMS
Input Level: Nominal 250 
 Maximum Input: 1 Volt RMS
External Paging Specifications:
Output Impedance: 600 OHMS
Output Level: Nominal 250  Maximum Output: 400  RMS
MECHANICAL SPECIFICATIONS
Dimensions and Weights:
KSU:27.8 in.
x 26.1 in. x 8.5 in.81.6 Ibs.713.0 mm x 670.0 mm x 219.0 mm37.0 kg
Power Supply:13.3 in.
x 19.0 in. x 4.8 in.19.4 Ibs.340.0 mm x 488.5 mm x 122.0 mm8.8 kg
Executive/Key Telephone:3.1 in.
x 8.0 in. x 8.6 in.2.2 Ibs.
80.0 mm
x 205.0 mm x 221.0 mm1.0 kg
Door Chime Box:5.1 in.
x 3.9 in. x 1.4 in.0.4 Ibs.131 .O mm x 99.0 mm x  35.0  mm0.2 kg
DSS Console: 2.0 in.x 7.4 in. x 8.8 in.1.3 Ibs.
52.0 mm
x 189.0 mm x 224.0 mm0.6 kg
ENVIRONMENTAL SPECIFICATIONS
Environmental Operating Conditions:
Temperature:
KSU and Telephones: 0 to 45 degrees C
Door Chime Box: -20 to 60 degrees C
Humidity: 10% to 95% noncondensing
(32 to 113 degrees F)
( -4 to 140 degrees F) 
						

							BUSINESSCOM PLUS 
ELECTRONIC KEYTELEPHONESYSTEMS
SECTION 2,FEWTURES
CONTENTSPAGECONTENTSPAGE
1.INTRODUCTION..................... 2-2
2. DESCRIPTION......................
Automatic Intercom Answer...........
Background Music (BGM)............. 2-2
Call Duration Timer................. 2-2
Call Forward With Follow-Me..........
Call Monitor....................... 2-3
Call Pickup.......................
Call  Announced.............. 2-4
Call Transfer Unannounced............ 2-4
Call Waiting....................... 2-4
Callback.........................
Camp-On......................... 2-5
CO Lines..........................
2-5
Common Use Line..................
Component Commonality............. 2-6
Conference, Add-On................. 2-6
Conference, Meet-Me................
Conference, Multi-Line............... 2-7
Conference, Unsupervised............. 2-7
Confirmation Tone..................
2-8
Dial Pulse To Tone (DTMF)
Conversion......................
Direct Inward System Access (DISA)..... 2-8
Direct Station Selection (DSS).........
Direct Station Selection (DSS)
Console........................
Do Not Disturb ...............
Do Not Disturb (DND) Override
By DSS Console..................
Door Chime Box...................
Dual Handsfree Hotline............ 2-10
Excluded System Features............
2-11
Executive Call Forward..............
Executive Override (Barge In).........2-12
External Alarm Signals To
Stations........................
2-12
Flash...........................
Flexible Line Appearance............
Flexible Station No. Assignment.......
Group Hunt......................
Group Hunt ................2-14
Handsfree Reply On Intercom.........
Hold............................2-15
Intercom........................
Last Number Dial..................
Line ....................
Message Waiting...................2-16
Microphone On/Off................
Music On Hold ..............
Night Class Of Service...............2-17
Night Transfer.....................
Off-Premises Extension..............2-18
Paging, All Call....................2-19
Paging, All External Zone............2-19
Paging, External Zone...............2-19
Paging, Internal Zone...............
Paging, Meet-Me..................
Private Line......................2-20
Recall Line Preference...............
2-21
Release Of Abandoned Calls
...................... 
Remote Busy Line Indication..........2-21
Ring 
.....................2-22
Ringing Line Preference.............2-22
Room Monitor....................
Save............................2-23
Single Step Access.................
Speed Dial.......................2-23
Step Calling......................2-24
Tenant Service ....................2-24
Three Minute Warning Tone..........2-24
Toll Restriction....................2-25
Transfer Recall Display..............2-25 
						

							1.INTRODUCTION
   
1.01This section lists and details the features available
in the Businesscorn Plus  Both
permanent and programmable features are discussed. This
section should be used in conjunction with Section 4,
SOFTWARE CONFIGURATION, when preparing the
Program Record Form.
2.DESCRIPTION
2.01This section is formatted in the following manner:
Description: discusses the basic elements of the feature.
Conditions: lists and describes conditions that limit or
enhance the feature under discussion.
Basic Programming: lists required programming, i.e.,
programming necessary for feature operation.
 Programming: lists programs that limit or enhance
feature operation.
Feature Interactions: lists features that directly affect the
feature under discussion.
AUTOMATIC INTERCOM ANSWER
Description:
This feature permits single-step answer of an internal call.
Conditions: None
Basic Programming: None
Related Programming: None
Feature Interactions:
Intercom
BACKGROUND MUSIC (BGM)
Description:
This feature permits station speakers and external zones to
receive Background Music.
Conditions:
(a) BGM is a customer supplied item.
(b) BGM can serve as a source of Music On Hold.
(c) BGM is interrupted at a zone and/or station by an
incoming call, and at a station by an outgoing call.
(d) BGM is interrupted at stations utilizing Room Monitor.
(e) BGM utilizes one Intercom link.
Basic Programming:
Program 26-Background Music
Related Programming:
Program l&External Paging Output
Feature Interactions:
CO Lines
Hold
Intercom
Music On Hold (MOH)
Room Monitor
CALL DURATION TIMER
Description:
This feature permits a user to time the duration of an
outgoing CO call.
Conditions:
(a) This feature is available only on Executive Display
telephones.
(b) The timer starts from 0 to 255 seconds after CO line
seizure depending upon programming.
(c) This feature can be manually started.
(d) If a Hold is implemented during a CO call, the timer is
disabled and the display returns to its normal condition. 
						

							Basic Programming:
Program  Duration Timer
Related Programming:
Program  Duration Start Timer
Feature Interactions:
CO Lines
Hold
CALL FORWARD  FOLLOW-ME
Description:
This feature permits the automatic transfer of an incoming
Intercom call to a second station (Call Forward). The
destination of the forwarded call can be changed to yet a third
station and so on (Follow-Me).
Conditions:
(a) The originating station can change the destination of the
Call Forward.
(b) Only the originating station can cancel a Call Forward.
(c) The destination station can change the destination of the
Follow-Me.
(d) Program 49 (Excluded System Features) can disable this
feature.
(e) A call cannot be forwarded to a station that has invoked
DND.
(f) Executive Call Forward overrides Call Forward With
Follow-Me.
Basic Programming: None
Related Programming:
Program 49-Excluded System Features
Feature Interactions:
CO Lines
Executive Call Forward
Intercom
CALL MONITOR
Description:
This feature permits the on-hook dialing of an Intercom or
CO telephone number.
Conditions:
(a) Telephones without speakerphones must lift the handset
to engage in a two-way conversation once the call is
established.
(b) The user can also monitor a CO call if placed on Hold.
Basic Programming: None
Related Programming: None
Feature Interactions:
CO Lines
Intercom
CALL PICKUP
Description:
This feature permits a station user to intercept an Intercom
call intended for another station.
Conditions:
(a) Program 49 (Excluded System Features) can disable this
feature.
Basic Programming: None
Related Programming:
Program 49-Excluded System Features
Feature Interactions:
Intercom
2-3 
						

							 
 
CALL TRANSFER ANNOUNCED
Description:
Thisfeature permits the voice announced transfer of an
established CO call.
 
Voice Announce must be programmed.
Program 49 (Excluded System Features) can disable this
feature.
If the transferred call is not answered within a
programmed period of time, the call reverts back to the
transferring station.
This feature is accessible from a key telephone or DSS
Console.
Basic Programming:
Program 24-Voice Announce /Tone Signal Call
Related Programming:
Program  Console Port Assignment
Program 
 Transfer Timer
Program 39-DSS Transfer Timer
Program 49-Excluded System Features
 Feature Interactions:
CO Lines
Direct Station Selection (DSS) Console
Intercom
CALL TRANSFER UNANNOUNCED
Description:
This feature permits the transfer of an established CO call,
with ringing, to a second station.
Conditions:
  :
(a) If the transferred call is not answered within a
programmed period of time, the call reverts back to the
transferring station.
(b) Program 49 (Excluded System Features) can disable this
feature.
(c) This feature is accessible from a key telephone or a DSS
Console.
(d) Tone Signal must be programmed.
Basic Programming:
Program  Announce /Signal Tone Call
Related Programming:
Program  Console Port Assignment
Program 
  Timer
Program 39-DSS 
 Timer
Program 49-Excluded System Features
Feature Interactions:
CO Lines
Direct Station Selection (DSS) Console
CALL WAITING
Description:
This feature permits two types of Call Waiting:
(a) CO Call Waiting.
 Intercom Call Waiting.
CO Call Waiting allows a station with a seized CO line to
receive ringing for another incoming call on another line.
Intercom Call Waiting allows a station with a seized Intercom
link to receive ringing for another incoming Intercom call.
Conditions:
Intercom Call Waiting is unavailable at stations using
Handsfree Reply On Intercom.
‘Iwo levels of Intercom Call Waiting are available through
programming:
(1) User-controlled: allows user to initiate the Call
Waiting signal.
(2) Automatic: the Call Waiting signal is automatically
initiated.
Callback and Camp-On are unavailable when the
automatic mode of Intercom Call Waiting is in use.
Call Waiting (CO) signals are blocked by all levels of Do
Not Disturb when Do Not Disturb is in use. Intercom Call
Waiting signals are blocked by Do Not Disturb (level 2
and level 3 where LED lights steadily) when Do Not
Disturb is in use.
This feature is permanent for Intercom calls with respect
to the DSS Console, i.e., the DSS Console has
permanent override capabilities.
Basic Programming:
Program 16-CO Call Waiting
Program 23-Intercom Call Waiting
Related Programming ,
Program  Console Port Assignment