Trillium Panther Ii Feature Module Iv System Manual

Mite1 Standard Practise 
Modular Connector 
c 
Figure 3-3: Connecting the MDF to the KSU 
Feature Module IV & On Premise Station Unit 
Page 16  

Panther II 820/1032/2064-297 
Left Side of ONS Unit 
Figure 3-4: Connecting the KSU Station Ports to the ONS Unit 
Feature Module IV & On Premise Station Unit 
Page 17  

Mite1 Standard Practise 
Step 7 
Step 8 
Step 9 Program the type of line select for the ONS stations: ’ 
From the Panther II Display Set at Station 10 
Dial *#015 to enter programming mode 
Dial access code 113YY where YY is the 2-digit station number of the ONS 
device 
Enter the desired data code: 
0 for Auto Intercom (for a voice mail system) 
2 for Manual Line Select (single line set or auto attendant) 
Press the # key to store your selection 
Repeat steps c to e for each ONS station 
Press * to exit...

Panther II 820/1032/2064-297 
Dipswitch 
Right Side of ONS Unit 
Figure 3-5: On Premise Station Unit Dipswitch 
Feature Module IV & On Premise Station Unit 
Page 19  

Mite1 Standard Practise 
On 
On Off On 
60 - 
1200 
Off 
Off On On 
60 - 
1300 
On 
Off On On 
60 - 
1400 
Off 
On On On 
60 - 
1500 
On 
On On On 
60 - 
1600 
Default: Flash Recognition is 60 to 100 ms 
Cancel is 100 ms 
Table 3-8: Dipswitch Settings 
1200 
1300 
1400 
1500 
1600 
Feature Module IV & On Premise Station Unit 
Page 20  

Panther II 820/1032/2064-297 
4. ON PREMISE STATION DEVICES 
General 
4.01 This section provides a brief description of each ONS device and identifies any 
special programming requirements. 
Single-Line Set 
4.02 You can perform certain Panther features from a single-line (tone only) telephone 
that’s connected to an ONS station. However, you must frst program the ONS station for 
a single-line set (access code lOOYY, data code 5) and for Manual Line Select (access 
code 113YY, data code 2) if you want...

Mite1 Standard Practise 
Incoming external calls can be transferred from a station to the auto attendant. The auto 
attendant is able to answer and redirect the transferred call to a station. 
Since internal call 
transfer isn’t available with the Panther II System, an auto attendant can’t direct internal 
calls to stations within the system. For the same reason, internal calls that are forwarded 
to the auto attendant can’t be redirected either. 
Calls that arrive at a busy ONS auto attendant port can...

Panther II 820/1032/2064-297 
Calls that arrive at a busy ONS voice mail port can be forwarded to another ONS voice 
mail port. Refer to the section 
Setting Call Forwarding in this Practice. 
You can program incoming external calls to ring at the voice mail system 
To allow 
incoming external calls to ring a voice mail port, you must program the lines to ring at the 
ONS station port that the voice mail system is connected to. 
Refer to 
Flexible Ringing 
Assignment 
in the Programming Practice of the...

Mite1 Standard Practise 
5. ON PREMISE STATION UNIT PROGRAMMING 
General Programming 
5.01 This chapter provides programming instructions for the ONS Unit. The program- 
ming parameters for the ONS Unit and ONS stations are listed in the tables of this chapter. 
To program ONS features: 
Step 1 Dial *#015 on the Panther II Display Set at Station 10 
Step 2 Select the desired feature from the table and dial the appropriate 3- to 7-digit 
access code. 
Step 3 To change the default, dial the data code of...

Panther II 820/1032/2064-297 
The hold and transfer signals generated by the ONS unit are produced only within the 
Panther system, whereas the flash and cancel signals are generated both within the Pan- 
ther system and on the central office lines. 
If you are connecting an auto attendant to an ONS port, or if you want to be able to trans- 
fer calls from a single-line set, you must program the flash-hook as a Transfer signal. 
You can set the ONS Flash/Cancel Recognition time to correspond to the...