Trillium Talk To 616 General Information Manual

INSTALLATION 
Introduction 
This manual details the procedures to install and 
program the TalkTo 676 Electronic Key Telephone System. 
A section on Troubleshooting is also included. 
Installation is easy, and can be carried out by a cer- 
tified installer, using standard cable runs and modular 
jacks; or if so desired by the end-user, using standard 
modular telephone line cords, extension cords, and 
adapters. 
Preparation 
The installer should ensure that the area chosen 
to mount the KSU is: 
l...

INSTALLATION 
KSU’ Installation 
.; 
.: The Door Answer Unit measures 6.25 inches x 8 
inches and should be wall mounted adjacent to the 
KSU. The KSU contains no user adjustable controls or 
parts. All switches used during programming are acces- 
sible at the exterior of the KSU. An indicator on the left 
side of the KSU flashes when the system is up and 
running. 
The 11OV ac three-wire out/et should be 
dedicated to the KSU. 
At the service panel, the elec- 
trical breaker for this outlet should be...

INSTALLATION 
Stations 10 - 21 - 
Program 1 
Program 2 1 
Not Used - 
Battery - 
Status Indicator - 
Reset Push Button’ 
a 14.17” 
(36Omm)~~ 
__--- 13.38” (340mm) - 
- 
3 
1 
- 
R 
I 
I _ 
L 
n n 
Z’ 
* 12.82” (326mm) -4  
4 i 1.95” (304mm)pdjlound Lug 
II- 
 
El 
Stations 
- 
22 
- 25 
/ 
Page Out 
- PFUC 
- Door 
- CO 5.6 
- co 3.4 
- co 
1.2 
 Music In 
TalkTo 616 KSU Cabinet - Dimensions 
6 t  

INSTALLATION 
Station Wiring - Method 1 Method 1 Wiring Table 
This method uses 25 pair standard cabling and a 
66 Type Punch Down Block, to connect 12 stations, and 
4 modular line cords and half 66 Type Punch Down Block 
to connect the remaining 4 stations. Cable runs to the sta- 
tion locations use communication cable (2 pair 24 AWG), 
625 type four-wire jacks, and modular line cords. 
Adjacent to the left hand side of the KSU, install the 
66 Type Punch Down Block (S66-M&50/? of similar). 
Prepare...

S66-M4-25TLM-A 
4 Wire Modular Line Cords Block , 
Jack 
STA 22 
Plug 
S66-Ml-!NOR 
Block CO 5.6 
co 3.4 
co 1.2 
2 2 Pair 
Communication Cable Gnd 616 KSU 
625 Type Jack 
with 
Set 
11OV AC 
 
4 Cabies I 
 
2 Pair 
Communication Cable  12 Cables 
Pwr 
tl 
0 625 Type Jack 
with Set 
#I2 AWG 
 
TII 428 
Surge Protector 
4 Wire Modular? 
Line Cords 
 TalkTo Set 
TalkTo Set 
4 Stations Total  12 Stations Total 
Metal Cold Water Pipe 
RJ14C Jacks 
8 
System Wiring - Method 1 C.O./PABX Lines  

INSTALLATION 
‘:‘;,; 
:

10 
Station Wiring - Method 2 
This method assumes that connections from the 
KSU to Stations will be made using 625 jacks and modular 
cords, and does not require the use of any special tools. 
However, since twelve station outputs from the KSU are 
terminated with a 25 pair plug, it is necessary to use a 
short 25 pair cable, and an adapter which converts the 
25 pair cable to 12 modular jacks (ProtoTel PX25ST4-727 
or similarj. 
Adjacent to the left hand side of the KSU, install the 
PX-25ST4-727 Type...

Music Input Paging Output 
The TalkTo 616 System provides both music on hold 
(MOH) and background music if an external music source 
is provided. This music source is connected via the 
Music 
In 
jack on the KSU with a l/8 inch miniature plug. The 
KSU requires a music signal not exceeding 50mV rms. The TalkTo 676 System provides external loudspeaker 
paging by the stations through the paSe Out jack. The 
voice output from the KSU to the customer provided exter- 
nal amplifier is connected with a l/8...

INSTALLATION 
. . : 
: .: 
616 KSU 
Door 
The Door Answer Module with front cover detached 
showing the two screw terminals. 
Door Answer Unit 
The Door Answer Unit (DAU) is mounted on the 
backboard with the screws supplied. The Door Answer 
Unit is connected with a modular 6 conductor cord sup- 
plied with the Unit. At the KSU plug the 6 conductor cord 
into the jack labeled 
Door. At the Door Answer Unit, plug 
the cord into the jack labeled 
DA. 
Door Answer Unit 
I 
Plug Screw Terminals 
6 Conductor...

INSTALLATION 
-6.26” 
(159mm) 
L-5.78” 
Power Failure Transfer Option 
To provide telephone service in the event of a com- 
merical power outage, a Power Failure Transfer Unit (PFT) 
must be installed. The PFT will allow all 6 of the TalkTo 676 
system’s C.O./PABX lines to be transferred to 6 individual 
industry standard 2 wire telephones when the commer- 
cial power fails. 
Mount the PFT unit on the backboard near the 
KSU. Install the 2 conductor special cable supplied with 
the unit. At the KSU, plug...