Uniden Bc60xl Vhf Uhf Scanner Owners Manual

							Operation
Keylock
Keylock prevents accidental key entries.
To lock:
Only theS,M, and
Kkeys will function.
To unlock:
If keys do not work, press
Kto unlock keys.
TheK/Lindicator
disappears from the
display.
8
H:...Bc60xlt.vp
Mon Aug 30 15:33:58 1999 Color profile: Disabled
Composite  Default screen 
						

							Programming Channels
1. Select frequency.
2. Select channel using Manual mode.
Note:For channel 10,
press
1,0.
9
H:...Bc60xlt.vp
Mon Aug 30 15:34:00 1999 Color profile: Disabled
Composite  Default screen 
						

							— OR—
3. Enter frequency.
Each digit displays as you
enter it.
The decimal displays as a
dash.
If you make a mistake,
press
.twice and start
over.
3a. If frequency outside range.
Programmed frequencies
must be within the bands
shown on the back of the
scanner, and on page
three of this guide.
10
H:...Bc60xlt.vp
Mon Aug 30 15:34:02 1999 Color profile: Disabled
Composite  Default screen 
						

							4. Recheck frequency.
The frequency appears
one digit at a time in
sequence.
Repeat these steps to program each channel.
You can program the same frequency into two or more
channels, if desired.
Channels with no frequency programmed are skipped during
scanning.
After programming your scanner, record the frequencies in the
table below (or another convenient place) so you can easily
reprogram the scanner in case the memory is accidentally
erased. Use pencil so you can change your entries at a later
date.
Channel Frequency Notes
1
2
3
4
5
6
7
8
9
10
11
H:...Bc60xlt.vp
Mon Aug 30 15:34:03 1999 Color profile: Disabled
Composite  Default screen 
						

							How Squelch Works
Think of “SQUELCH” as a
gate.
If the gate is set too low
(SQUELCH too low),
everything (all noise as
well as signals) gets
through.
If the gate is set too high
(SQUELCH too high),
nothing gets through.
If the gate is set just right
(SQUELCH set properly),
just the desired signals
get through.
12
H:...Bc60xlt.vp
Mon Aug 30 15:34:04 1999 Color profile: Disabled
Composite  Default screen 
						

							Setting the Squelch
1. Turn until hiss heard.
This action lowers the
“squelch gate,” allowing
all signals and noise to
get through.
No signal should be
present when adjusting
squelch.
Scanner doesn’t scan
with squelch open.
2. Turn just until hiss stops.
This action raises the
“squelch gate,” allowing
only strong signals to get
through.
Scanner should begin
scanning after two
seconds.
Note:You must have at
least one channel
programmed before the
BC60XLTwill scan.
Scanning Programmed Channels
Turn the scanner on.
Channel numbers
advance rapidly.
Note:When you turn the
scanner on, it will always
be in Scan mode.
13
H:...Bc60xlt.vp
Mon Aug 30 15:34:06 1999 Color profile: Disabled
Composite  Default screen 
						

							The scanner skips any
unprogrammed channels,
and locked out channels.
When transmission received:
Scanner stops on that
channel.
When the transmission
ends, scanning resumes
after a two second delay.
To hold on that channel:
14
H:...Bc60xlt.vp
Mon Aug 30 15:34:07 1999 Color profile: Disabled
Composite  Default screen 
						

							To resume scanning:
Scanner immediately
resumes scanning.
To listen to or program a specific channel:
Note:For channel 10,
press
1,0.
Press
Sto resume
scanning.
15
H:...Bc60xlt.vp
Mon Aug 30 15:34:09 1999 Color profile: Disabled
Composite  Default screen 
						

							Channel Lockout
Channel Lockout lets you skip channels during scanning.
There are two ways to lock out a channel:
Manual Mode
Use Manual mode to
select the channel you
want to lock out.
Note:For channel 10,
press
1,0.
16
H:...Bc60xlt.vp
Mon Aug 30 15:34:11 1999 Color profile: Disabled
Composite  Default screen 
						

							Scanning Mode
When the scanner stops
on a channel during
scanning, you can lock
out that channel by
pressing
O.
Because the locked out
channel is no longer
scanned, scanning
resumes immediately
after pressing
O.
To unlock a channel:
Use Manual mode to
select the desired
channel.
17
H:...Bc60xlt.vp
Mon Aug 30 15:34:12 1999 Color profile: Disabled
Composite  Default screen