Vidikron Projector Model 75 User Manual

Vidikron Vision Model 65/Model 75 Installation/Operation Manual 5 
2.1 
Vision 65/75 at a Glance
Figure 2-1 and Figure 2-2 show the key Vision 65/75 components. 
Figure 2-1. Vision 65/75 Front/Side/Top View
1.EXHAUST VENT
2.ZOOM TAB  
Use this to change the projected image size. 
3.TOP IR SENSOR
4.LAMP LED 
Indicates lamp status as follows:
 Off during normal operation
 Red when the lamp has exceeded its usage life or developed a problem
2Controls and Functions
12
7 8 9 10
56
43 

Controls and Functions
6 Vidikron Vision Model 65/Model 75 Installation/Operation Manual
5.POWER/STANDBY LED 
Indicates power status as follows:
 Orange when the projector is in standby mode
 Flashes green for approximately 45 seconds after the projector is turned on to indicate 
that the lamp is warming up
 Green during normal operation
 Flashes orange for approximately 110 seconds after the projector is turned off to 
indicate that the lamp is cooling down
 Red when an internal failure requiring...

Controls and Functions
Vidikron Vision Model 65/Model 75 Installation/Operation Manual 7 
Figure 2-2. Vision 65/75 Rear/Bottom/Side View
1.CABLE ACCESS DOOR 
Open to access connectors. 
2.DOOR RELEASE BUTTON
3.CABLE OPENING 
Pass cables through this opening.
4.LAMP MODULE COVER 
Remove this cover to access the lamp compartment.
5.FRONT/REAR ADJUSTERS 
Use these to adjust the projector height or projection angle.
6.CEILING MOUNT HOLES  
Use these to attach the ceiling bracket to the projector.
4321
565 

Controls and Functions
8 Vidikron Vision Model 65/Model 75 Installation/Operation Manual
2.2 
Vision 65/75 Rear Panel
Figure 2-3 shows the Vision 65/75 rear panel.
Figure 2-3. Vision 65/75 Rear Panel
1.HDMI 1 (Digital) 
HDCP-compliant digital video input for connecting a DVD player or HD tuner with a DVI 
or HDMI output.
2.HDMI 2 (Digital)
3.COMP 1 (RCA connectors) 
Standard- or high-definition (480i/480p/576i/576p/720p/1080i/1080p) Component 
(YPrPb) input for connecting a DVD/HD-DVD/BD player, HD...

Controls and Functions
Vidikron Vision Model 65/Model 75 Installation/Operation Manual 9 
9.12-VOLT (250 mA) TRIGGER OUTPUT (3.5-mm, mini phono jack)  
Connection for a 12-volt trigger-controlled device. This can be a retractable screen, 
screen mask or the Vidikron CineWide with AutoScope system. 
10.COMP 2 / RGB 
Five BNCs for connecting either RGB or component (YPbPr), SD or HD video signals. (The 
Vision 65/75 automatically detects the signal format.) 
2.3 
Vision 65/75 Remote 
Control
Figure 2-4...

Controls and Functions
10 Vidikron Vision Model 65/Model 75 Installation/Operation Manual
1.LIGHT  
Press to illuminate the buttons. 
2.ON / OFF 
Use these buttons to turn the projector on or off.
3.Source Selection Buttons: 
 
VID 
Press to select Composite video input as the source.  
 
S-VID (S-Video) 
Press to select the S-Video input as the source.  
 
COMP1  
Press to select Component 1 video input as the source.  
 
COMP2  
Press to select Component 2 video input as the source.  
 
RGB  
Press to...

Controls and Functions
Vidikron Vision Model 65/Model 75 Installation/Operation Manual 11 
5.Picture Adjustment Buttons:  
 
BRT (Brightness) 
Press to adjust black level.  
 
CONT (Contrast) 
Press to adjust white level.  
 
COL (Color) 
Press to adjust color intensity.  
 
TINT 
Press to adjust color hues. 
6.Memory Preset Buttons: 
 
ISF NIGHT 
Press to recall settings for the current input from the “ISF Night” memory preset.  
 
ISF DAY 
Press to recall settings for the current input from the “ISF...

Controls and Functions
12 Vidikron Vision Model 65/Model 75 Installation/Operation Manual
9.Picture-In-Picture (PIP) Controls: 
 
ACT 
Press to switch to the active window in PIP mode. 
 
PIP 
Press to activate PIP mode.  
 
PIP+ 
Press to enlarge the PIP window. 
 
PIP- 
Press to shrink the size of the PIP window.
10.LENS 
Press to access the lens shift controls. 

Vidikron Vision Model 65/Model 75 Installation/Operation Manual 13 
3.1 
Remote Control
To install batteries in the remote control, push the 
battery cover and slide it off. Install the two AAA 
batteries with the correct polarity and then replace 
the cover. 
Notes on Batteries Make sure that the battery polarities are correct when installing the batteries.
 Do not mix an old battery with a new one or different types of batteries.
 If you will not use the remote control for a long time, remove the...

Installation
14 Vidikron Vision Model 65/Model 75 Installation/Operation Manual
3.2 
Quick Setup
Table 3-1 gives a quick overview of the Vision 65/75 installation process. The sections 
following this one provide detailed instructions. 
   
Installation should be performed by a qualified custom video installation 
specialist.
Table 3-1. Installation Overview 
StepProcedureFor Details, Refer to 
page...
1Choose a location for the projector15
2
If installing a CineWide-equipped projector: Install...