Vidikron Projector Vision Model 15 User Manual

							Installation
Vidikron Vision Model 15 Installation/Operation Manual 27 
S-Video/Composite Video Connections: Connect your S-Video and composite video 
sources to the Vision 15 as shown in 
Figure 3-12.
Figure 3-12. Composite and S-Video Connections
Composite   S-Video
DVD Player, VCR,
LaserDisc, Camcorder
etc. 
						

							Installation
28 Vidikron Vision Model 15 Installation/Operation Manual
RS-232 Controller 
Connection
Use the communication cable supplied with the projector to connect a PC or home theater 
control/automation system (if present) to the RS-232 port on the Vision 15; see 
Figure 3-13. 
For more information about using this connection, refer to Serial Communications on 
page 59.
Figure 3-13. RS-232 Control System Connection
➤
876
592143
Pin   Function
2    Transmit Data (in)
3    Receive Data (out)
5   Ground
1, 4, 6, 7, 8, 9  Not Used
To PC or
Automation/
Control System
Communication
Cable, 9-pin Mini-DIN
Male to 9-pin D-Sub
Male, 15 cm (5.9 in.) 
						

							Installation
Vidikron Vision Model 15 Installation/Operation Manual 29 
Connecting 12-Volt Trigger 
Output to External Theater 
Equipment
If your home theater contains a retractable screen, screen mask or other 12-volt 
trigger-activated equipment, connect it to the 12-volt trigger output as shown in 
Figure 3-14. 
Figure 3-14. Connecting the 12-Volt Trigger Output to Other Equipment
3.7 
Turning on the Power
1. Turn on your source components.
2. Plug the female end of the power cord into the 
AC receptacle on the rear of the Vision 15 (AC 
100V ~ 240V). (The Vision 15 ships with various 
types of AC power cords. Choose the one that is 
appropriate to your locale.) 
3. Connect the other end to your AC power source. 
The power indicator lights blue to indicate that 
the Vision 15 is in “standby” mode.
4. Press the ON button on the remote control to 
turn on the projector. The power indicator turns 
off.
5. After a brief warm-up period (approximately 10 seconds), the Vision 15 will start 
projecting.
Retractable Screen
or other, 12-volt
trigger-activated equipment
Red = +12V (Tip) Black = Ground (Sleeve) 3.5-mm
mini plug 
						

							Installation
30 Vidikron Vision Model 15 Installation/Operation Manual
3.8 
Changing the OSD 
Language
The Vision 15 OSD language is initially set to English, but can also display the menus in 
French, Spanish, Italian or German. To change the OSD language:
1. Press MENU.
2. Select Installation from the Main Menu and press ENTER.
3. Select Language from the Installation Menu and press ENTER.
4. Press  or  to highlight the desired language and press ENTER. 
3.9 
Adjusting the Picture 
Orientation
By default, the Vision 15 is configured for a “floor/front” installation, in which the projector is 
installed upright and in front of the screen. If it is installed behind the screen and/or mounted 
on a ceiling, you must change the picture orientation. To do this:
1. Press MENU on the remote control. 
2. Select Installation from the Main Menu and press ENTER. 
3. Select Orientation from the Installation Menu and press ENTER.
4. Choose Floor Rear, Ceiling Front or Ceiling Rear to match the installation method. 
						

							Installation
Vidikron Vision Model 15 Installation/Operation Manual 31 
3.10 
Primary Lens Adjustments
The Vision 15 gives you a great deal of control over the picture size, position and focus. 
Figure 3-15 shows the location of the focus and zoom controls; Figure 3-16 shows the 
location of the lens shift controls. 
Focus and ZoomTo focus the projected image, rotate the focus ring left or right.
To make the picture larger (zoom in), rotate the zoom ring to the left (toward the Vidikron 
logo). To make the picture smaller (zoom out), rotate the zoom ring in the other direction.
Figure 3-15. Focus and Zoom Controls
Zoom ring
Focus ring
Zoom in Zoom out
Focus
RingZoom
Ring 
						

							Installation
32 Vidikron Vision Model 15 Installation/Operation Manual
Shift To change the projected image position, rotate the vertical and/or horizontal lens shift dials.
Figure 3-16. Vertical and Horizontal Lens Shift Controls
➤
Do not force the lens shift dials beyond their respective ranges. This may 
cause the projector to malfunction. Caution
Lens shift dial
( Horizonta l )Lens shift dial
(Vertical) 
						

							Installation
Vidikron Vision Model 15 Installation/Operation Manual 33 
3.11 
Installing and Adjusting 
the CineWide Anamorphic 
Lens
If you are installing a Vision 15ET/CineWide, proceed as follows to install and adjust the 
anamorphic lens. 
The CineWide anamorphic lens mount kit consists of everything shown in Figure 3-17. Some 
components shipped with your projector may differ slightly from what is shown in these 
instructions. 
Figure 3-17. Anamorphic Lens Mounting Assembly - Exploded View
1. Use the Height/Pitch Adjustment Screws (2) and Washers (3) to attach the Lens 
Mounting Bracket (5) to the Anamorphic Lens (1).
2. Remove the nut and rubber collar from each Swell Latch Assembly (4). 
It is extremely important that the primary lens is properly adjusted 
before you install the anamorphic lens. Ensure that the image from 
the primary lens is perfectly centered on the screen. Note
3    Height/Pitch
      Adjustment 
      Screw,
      4-40 x 1/4  
      (4x)
4    Swell
      Latch    
      Assembly     
      (2x)1    Anamorphic Lens
2    Washer (4x)
6    Anamorphic Lens
      Base Plate 5    Anamorphic Lens
      Mounting Bracket 
						

							Installation
34 Vidikron Vision Model 15 Installation/Operation Manual
3. Secure the lens (with the mounting bracket attached) to the Lens Base Plate (6) using the 
swell latches. 
 
Adjusting the Lens Height and Angle: 
1. Project a white field on the screen.
2. Loosen the four Height/Pitch Adjustment Screws just enough to allow vertical 
movement of the lens assembly.
3. Slowly move the anamorphic lens into place so that there are no shadows on the top or 
bottom of the screen:
 
4. Then, adjust the anamorphic lens angle so that the projected image is rectangular:  
  
The anamorphic lens will almost always be angled with respect to the projector; this is 
normal. 
5. When the height and angle are properly set, tighten the Height/Pitch Adjustment 
Screws to secure the lens in place. 
 
To avoid clipping the corners of the image, position the anamorphic lens 
as close as possible to the primary lens. 
There may be some pincushion distortion even after the lens is properly 
adjusted, especially at shorter throw distances. If this is the case, Vidikron 
recommends that you slightly over-scan the image into the screen frame 
area to mask the distortion. 
Tip
Too HighToo Low
Correct position
Correct Lens Angle
Incorrect Lens Angle
Note 
						

							Vidikron Vision Model 15 Installation/Operation Manual 35 
4.1 
Using the On-Screen 
Menus
 Press the MENU button on the remote control to display the Main Menu. To select a menu 
item, use the 
 and  buttons on the remote control to highlight it. Press ENTER to 
confirm your selection. 
 Use the arrow buttons to select menu items or change settings. 
 Press EXIT to return to the previous menu. 
 Press MENU to turn off the OSD menu. (When the Main Menu is displayed, pressing EXIT 
also turns off the menu.)
The Vision 15 OSD menus are arranged hierarchically, as shown in Figure 4-1. Depending on 
the selected input source and signal characteristics, some menu options may not be 
available. 
4Operation 
						

							Operation
36 Vidikron Vision Model 15 Installation/Operation Manual
Figure 4-1. Vision 15 OSD Menu Structure
Main MenuThe Main Menu is the starting point for accessing all projector functions. (You must enter a 
passcode to access the ISF menu.)
Source Select
Video
S-Video
Component
HDMI
DVI-D
DVI-A
Picture Adjust
Picture Memory ISF Night, ISF Day or Custom
Brightness
Contrast
Color
Tint
Sharpness 0 ... 6
Gamma 1.5, 1.8, 2.0, 2.2, 2.35, 2.5
Color Temp.5400 K, 6500 K, 7500 K or 
8500K
Color SpaceAuto, HDTV, SDTV, RGB-Video 
or RGB-PC
BrilliantColor™ On or Off
Black Level 0 IRE or 7 IRE
Save Settings
Reset to Defaults
Aspect Ratio
16:9
4:3
Letterbox
IntelliWide
Cinema
IntelliWide 2.35 (Vision 15ET/CineWide only)
Installation
Language English, French, Spanish, 
German or Italian
OrientationFloor Front, Floor Rear, Ceiling 
Front or Ceiling Rear
KeystoneV. Keystone
H. Keystone
OverscanOverscan Type
Overscan Adjust
(0 ... 5)
YUV/RGB Adjust
(Component and DVI-A 
signals only)H. Position
V. Position
Clock
Phase
Reset
OSD Timeout 0, 5, 15 or 60 sec.
Vertical Correction
(Vision 15ET/CineWide only)
Information
Source
(read only) Resolution
H. Frequency
V. Frequency
Aspect Ratio
Picture Memory
Lamp Hours
Firmware
Serial
Setup
Lamp Power 180W or 230W
Lamp Reset
Sync Threshold
(Component input only)
Source Select Auto or Manual
Film Mode Auto or Off
DNR
Background Color Black or Blue
12V Trigger Normal or CineWide
Factory Reset Yes / No
ISF
Picture Memory ISF Night, ISF Day or Custom
Brightness
Contrast
Color
Tint
Sharpness 0 ... 6
Gamma 1.5, 1.8, 2.0, 2.2, 2.35, 2.5
Color Temp.5400 K, 6500 K, 7500 K or 
8500K
BrilliantColor™ On or Off
Black Level 0 IRE or 7 IRE
White BalanceR/G/B Gain
R/G/B Offset
DNR 0 ... 16
Save Settings
Blue Image On or Off
Splash Screen Timer 0, 5, 15 or 60 sec.
Reset to Defaults
Vision 15
Source Select
Picture Adjust
Aspect Ratio
Installation
Information
Setup
ISF
➤