Vidikron Projector Vision Model 20 User Manual

Vidikron Owner’s Manual
40
     
English
Install
Press Enter on selected feature to open the Install menu. 
Language: There are 5 different menu languages available: English, French, Spanish, German and Italian.
Picture Orientation: The projector can be installed on a ceiling or in a rear screen configuration with one or more mirrors. There are four 
settings: FLOOR FRONT, CEILING FRONT, FLOOR REAR, and CEILING REAR.
Keystone: Corrects the trapezoidal distortion as a result of the angle of projection...

     
English
Menu
   41
Service
The Service menu is passcode protected and for use by Vidikron per-
sonnel only. Many of the adjustments available in this section are 
intended for use by trained service personnel only. If you are having 
difficulty with one of these items, please contact your Vidikron Dealer 
for service. 
White Balance
Vision Model 40
InstallStatusService
Image OptionsPicture Adjust
Please enter pass-code 
to access Service screen
RedGreen                                Blue...

Vidikron Owner’s Manual
42
     
English
Blue Enable 
This mutes the red and green image.
Use this function in combination with the external color bar pattern to 
adjust for proper color and tint settings without using a blue filter.To quickly exit this function, select any other color temperature in the
same adjustment window and return to the original temperature setting
or simply select another input source from the remote control and then
return to the original selected source.
Reset Lamp Timer
Use...

     
English
Additional Information
   43
Additional Information
Replace the Lamp (Contact your Vidikron Dealer) 
1. Loosen the screw of front
lamp cover. 2. Take off the front lamp
cover.
 
3. Loosen the three screws
on the lamp shield.
4. Take off the lamp shield. 5. Loosen the two screws on
the lamp module.
6. Pull out the lamp module
horizontally.  

Vidikron Owner’s Manual
44
     
English
Troubleshooting
7. Insert the new lamp mod-ule into the projector hori-
zontally until it is securely
in place.
8. Tighen  the two screws on the lamp module.  9. Put on the lamp shield. 
10. Tighten the three screws on
the lamp shield.
11. Put on the front lamp cover.
12. Tighten the screw of front lamp cover.   13. 
Turn on the power and go  into the 
Service
 menu, select
Lamp Reset Timer
 item to reset lamp usage counter.
Problem
Possible Cause
Remedy
This unit...

     
English
Additional Information
   45
No picture
This unit is not correctly connected to the input 
source device.Check the connection.
The input signal has not been correctly selected. Select the correct input signal with the input keys: Video, 
S-Video, Component, Component HD, RGB HD and 
DVI-I on the remote control.
POWER LED or LAMP LED blinking. Please contact your Vidikron dealer for assistance.
Image is unstable
The connection cables are not connected to this 
unit.Correctly connect the...

     
English
Additional Information   46
Specifications
Vision Model 20/ Vision Model 20ET Specifications   
Projector TypeDigital Light Proces sing™ (DLP™), Single  DMD™ ChipNative Resolution1024 x 576, (16:9)Aspect Ratios4:3, Letterbox,  16:9 Anamorphic, IntelliWideVideo StandardsNTSC, PALThrow DistanceV20: 1.71 to 2.06/ V20ET: 2.31 to 3.06
(Factor x Screen Width)
: Please refer to page 20 to page 23.
Light OutputCSMS** Specifications:  
Home Theater Calibration: 
457 ANSI Lumens, 17.55 Foot-Lamberts...

     
English
Additional Information
   47
*ANSI Lumen specification:This is the typical projector luminosity (brightness) specification found in most sales literature.  This measurement is included in Vidikron 
literature to allow for direct comparison with other manufacturers projectors.  These measurements can be taken at 9,000 to 13,000 degree 
Kelvin to get expected performance data when the projector is used in professional, commercial, and industrial displays.**CSMS Home Theater Calibration ANSI...

Vidikron Owner’s Manual
48
     
English
Dimensions
Unit: mm
332.49
160
400
280
33.76 40
149.99-150.01
131.5
125.41201.48-201.50 

     
English
Additional Information
   49
RS-232 Setup
Baud Rate: 115200 or 9600
Parity: None
Data Bits: 8 Bits
Stop Bits: 1 Bit
Flow Control: None
RS-232C Control Codes 
Code Function
X23 Switch to DVI_PC input
X56 Picture in picture display
X01 Power On
X24 Switch to YP
BPR input
X57 Picture by picture display
X02 Power Off
X25 Switch to BNC_PC input
X60 Switch language - English
X03 Message On
X35 Anamorphic
X61 Switch language - French
X04 Message Off
X36 Standard
X62 Switch language - Spanish
X10...