Vidikron Projector Vision Model 30et User Manual

41Vidikron Vision Model 30 Owner’s Operating Manual

On-Screen Display Menus
Background Color
To use the Picture-in-Picture or Picture-by-Picture features, press the ▲  or  ▼ arrow 
buttons to select  PIP/PBP Setup, then press ENTER. 
Select  PIP/PBP Enable  from the PIP/PBP Setup  menu. Press 
▲ or ▼ to select  Off or 
On , then press  EXIT
.
PIP/PBP Setup
PIP/PBP Enable
PIP Setup
PBP Setup
Press the ▲  or  ▼ arrows to select  PIP Setup, then press  ENTER.
Press the 
▲  or  ▼ arrows to select  PIP...

42Vidikron Vision Model 30 Owner’s Operating Manual

On-Screen Display Menus
White Balance
Gamma Selection
ICC Adjust
Gain: Use the Gain controls in the White Balance sub-menu to correct color imbalances 
in the bright areas of the image. A good way to do this is to use a test pattern consisting 
mostly of solid white areas, such as an 80 IRE “window ” pattern. If the white areas contain 
traces of red, green or blue, decrease the Gain for that color.
Offset:  Use the Offset controls in the White...

43Vidikron Vision Model 30 Owner’s Operating Manual

On-Screen Display Menus
Image Over Scan pushes the outside edge of the active picture area of the video signal 
out beyond the edge of the display area. 
Some television programs are produced based on the assumption that older television 
sets may not display the outer edges of the broadcast picture area. Over scan effectively 
trims away these inactive, outer edges and enlarges the remaining portion of the image 
to fill the display area.
Use the...

44Vidikron Vision Model 30 Owner’s Operating Manual

On-Screen Display Menus
Fan Speed: If you set the Fan Mode to Manual, select  Fan Speed and use the on-screen 
slidebar to adjust the speed. 
After changing either of these settings, press  EXIT to return to the previous menu. 
When you replace the projector lamp, you should also reset the lamp timer. To do this, select 
Lamp Reset Timer  from the Set Up menu. Press the right-arrow button on the remote to 
highlight “Yes,” then press  ENTER to confirm...

45Vidikron Vision Model 30 Owner’s Operating Manual

On-Screen Display Menus
The Vision Model 30 has been designed to incorporate setup and calibration standards 
established by the Imaging Science Foundation (ISF). The ISF has developed carefully crafted, 
industry-recognized standards for optimal video per formance and has implemented a 
training program for technicians and installers to use these standards to obtain optimal 
picture quality from Vidikron video display devices. Accordingly, Vidikron...

46Vidikron Vision Model 30 Owner’s Operating Manual

On-Screen Display Menus
Press the ◄ or  ► arrows to set the Splash Screen Timer. This timer controls how long the 
startup (ISF and Vidikron logo) image stays on-screen after you turn on the projector. Select 
from 5 to 60 seconds, in 1-second increments. When finished, press  EXIT.
Use ISF Enable  to control the display of the ISF logo on the Vision 30 splash screen upon 
power-up. 
Splash Screen Timer 
ISF Enable
CALIBRATED FOR: 

47Vidikron Vision Model 30 Owner’s Operating Manual

Lamp Replacement
The lamp should be replaced when it reaches the end of its life (typically 2000 hours), or 
sooner if a noticeable degradation in brightness occurs. 
1.  Turn off the projector and unplug the power cord. 
Allow the projector to cool down for approximately 
45 minutes prior to removing the lamp assembly for 
replacement.
2.  Remove the two screws from the lamp cover.
3.  Remove the lamp cover.
4.  Remove the two screws from the lamp...

48Vidikron Vision Model 30 Owner’s Operating Manual

Lamp ReplacementThis page is intentionally left blank. 

49Vidikron Vision Model 30 Owner’s Operating Manual

PROBLEMPOSSIBLE CAUSE REMEDY
The projector does 
not turn on
There  is  no  power  from  the 
power cable.
Plug the power cord into the 
AC power socket on the rear of 
the projector and an electrical 
outlet.
The power switch is not turned 
on. Turn on the power switch.
The projector was turned on 
again  within  the  cool  down 
time.
Wait until projector completes 
the cool down time. 
Lamp  cover  is  not  attached 
well.
C o r r e c t l y   a t t...

50Vidikron Vision Model 30 Owner’s Operating Manual

TroubleshootingThis page is intentionally left blank.