Vidikron Projector Vision Model 60 User Manual

REPLACING THE LAMP (FOR SERVICE ONLY)
40
■ The light-source lamp and its lamp time
The light-source lamp has a service life. The life of lamps currently used for this projector is about 2000 hours.
[Average lamp life: 2000 hours]
When  the  light-source  lamp  approaches  the  end  of  its  service  life,  deterioration  progresses  rapidly.  Please  contact  your 
Vidikron  dealer  to  install  a  new  lamp  when  the  accumulated  lamp  time  exceeds  1900  hours.  Depending  on  the  operating...

■ After installing a new lamp, reset the lamp time counter inside the projector when this is done. A new count will start.
If the display of the accumulated lamp time has reached 2000 hours, the projector will not work (lamp does not light up) 
unless the lamp time is reset.
RESETTING THE LAMP TIME (FOR SERVICE ONLY)
1. Insert the power cord into the wall outlet
• The [STAND BY] indicator lights up when the main power is inputted.
2.  Press  the  [EXIT],  [MUTE],  [KEY  RESET]  buttons  on  the  remote...

By connecting a computer to the projector with a RS-232C cross cable (D-sub 9 pins), you can control the projector with 
the computer. The commands to control the projector and the response data format against the received commands are 
explained here.
For details, please consult the authorized dealer where you purchased your projector.
1. Communication Specifications
The communication specifications are as follows.
Baud Rate9600 bps / 19200 bps
Data Length8 bits
ParityNone
Stop Bit1 bit
Flow...

43
RS-232 EXTERNAL CONTROL
   3) Special parameters
   Input switching parameters
   Operation mode parameters
3. External Control Command Table
   Operation mode: Only Asking command is possible.
CharacterHex.Meaning
030Y/C
131VIDEO
333RGB1
434RGB2
535RGB3
CharacterHex.Meaning
000030h 30h 30h 30hStand-by mode
000130h 30h 30h 31hPower-on mode
000230h 30h 30h 32hCool-down mode
000430h 30h 30h 34hEmergency mode
FunctionCommandAskingData Type
Power OnELSENumeric ValueON/OFFSpecial Data
OPERATEU0FXXX○X...

TROUBLESHOOTING
The following is a basic troubleshooting guide that can assist you in resolving typical problems may result in normal operation. 
If you have encountered problems that are not listed in this guide, please contact your Vidikron dealer for assistance.
SymptomProbable CauseSolution
Power is not supplied.Is the power cord disconnected?Insert the power cord (plug) firmly.
Is the light-source lamp cover closed correctly?After  the  projector  goes  into  the  stand-by  state 
with  the  [STAND...

45
TROUBLESHOOTING
SymptomProbable CauseSolution
The upper part of the 
video image bows or 
distorts
If the input signal comes from a computer system, 
is  this  a  sync  signal  of  composite  sync  (Cs)  or  G 
on sync type?
Input  separate  sync  signals  for  vertical  sync  (V) 
and horizontal sync (H) signals
Remote control unit does 
not work.
Are batteries installed correctly?Match  the  polarities  of  batteries  correctly,  as 
shown on the battery cartridge.
Are batteries exhausted?Replace...

46
WHAT TO DO WHEN THESE MESSAGES ARE DISPLAYED
MessageCause (Contents)
�����
��������
No device is connected to the input terminal.
The terminal is connected but no signal is output from the connected device.
• The selected input mode (input terminal) name is shown above the mes-
sage.
→ Check the input image signal source.
�����
������������������������������������������
The frequency of the input video signal is out of range.
→ Please ensure the frequency level of the input video signals is within...

47
WARNING INDICATION
» About Warning Indicators
If something abnormal has occurred in the projector, the warning mode will be set in and the type of abnormality will be 
indicated by a combination of indicators displayed on the control panel as shown in the following table. The projector will 
then automatically stops projection and run the cooling fan for about 90 seconds.
» Action to be taken upon warning indications
Please follow the procedures below.
For No. 1-3
 No. 1 : Unplug from the main power...

48
�����������
�
����
�
����
�
����
�
DIMENSIONS 

SPECIFICATIONS
49
Vision Model 60 Projector:
Projector Type:D-ILA, 3-Chip. 0.7 in. diagonal
Native Resolution: 1400 x 788 (16:9) 
Aspect Ratios: 4:3, Letterbox, 16:9 Anamorphic
Video Standards: NTSC, PAL
DTV Compatibility: 480p, 720p, 1080i
Scan Frequency:Horizontal: 15 – 120 KHz
Vertical: 50 – 120 Hz
Picture Size (16:9 Screen):Recommended Width: 72 – 96 in.
Maximum Width: 240 in.  (16:9 screen)
Light Output: CSMS** Specifications: Home Theater Calibration: 487 ANSI Lumens;
17.9 Foot-Lamberts (fL); 1000...