ViewSonic N2010 Users Guide

							  N20 10                  LC DTV  D is p la y
U se r’s    G uid e
G uid e d e I’u tili sa te u r
G uía  d e u su ario
¨Ï¥Î¤â¥U
 
						

							E
N
G
L
I
S
H
Contents
ViewSonic     N2010   1 Product Registration.................................................................2
For Your Records.....................................................................2
Important Product Safety Instructions......................................3
Antenna Installation Instructions...............................................4
Cleaning the LCD Display.................................................4
Package Contents....................................................................5
Front View of the Product.........................................................6
Rear View of the Product..........................................................7
Remote Control.........................................................................8
Installation.................................................................................9
Getting Started
OSD Functions
Source Input-TV Mode.............................................................13
Source Input-YPbPr, AV, S-Video Mode..................................18
Other Information
Specifications...........................................................................20
Troubleshooting........................................................................21
Customer Support....................................................................22
Limited Warranty......................................................................23
Appendix
Safety Guidelines.....................................................................24
Compliance Information for U.S.A...........................................25
 
						

							E
N
G
L
I
S
H
ViewSonic     N2010    2
Copyright © ViewSonic Corporation, 2005. All rights reserved.
ViewSonic, the three birds logo, OnView, ViewMatch, and ViewMeter are registered trademarks of
ViewSonic Corporation.
Disclaimer: ViewSonic Corporation shall not be liable for technical or editorial errors or omissions
contained herein; nor for incidental or consequential damages resulting from furnishing this material,
or the performance or use of this product.
In the interest of continuing product improvement, ViewSonic Corporation reserves the right to
change product specifications without notice. Information in this document may change without
notice.
No part of this document may be copied, reproduced, or transmitted by any means, for any purpose
without prior written permission from ViewSonic Corporation.
To meet your future needs, and to receive any additional product information as it becomes
available, please register your product on the Internet at: www.viewsonic.com. The ViewSonic
Wizard CD-ROM also provides an opportunity for you to print the registration form, which you
may mail or fax to ViewSonic.
Product Registration
For Your Records
Product Name:
Model Number:
Serial Number:
Purchase Date:
Product disposal at end of product life
ViewSonic is concerned about the preservation of our environment. Please dispose of this product
properly at the end of its useful life. Your local waste disposal company may provide information
about proper disposal.
ViewSonic N2010
VS10563-1M
 
						

							E
N
G
L
I
S
H
IMPORTANT PRODUCT SAFETY INSTRUCTIONS
ATTENTION:
Follow and obey all warnings and instructions marked on your product and its operating instructions. For your safety,
please read all the safety and operating instructions before you operate this product follow its operating and keep this
user guide for future reference.
INSTALLATION
1.  Grounding or Polarization
Your product may be equipped with a polarized alternating-current line plug (a plug having one blade wider than the
other). This plug will fit into the power outlet only one way. This is a safety feature.If you are unable to insert the
plug fully into the outlet, try reversing the plug. If the plug should still fail to fit, contact your electrician to replace your
obsolete outlet. Do not defeat the safety purpose of the polarized plug.
2.  Overloading
Do not overload wall outlets, extension cords, or integral convenience receptacles as this can result in a risk of fire
or electric shock.
3.  Power Cord Protection
Power supply cords should be routed so that they are not likely to be walked on or pinched by items placed upon or
against them, paying particular attention to cords at plugs, convenience receptacles, and the point where they exit
from the product.
4.  Ventilation
Slots and openings around the cabinet are provided for ventilation.
To ensure reliable operation of the product and to protect it from overheating, these openings must not be blocked or
covered.
Do not block the openings by placing the product on a bed, sofa, rug or other similar surface.
Do not place the product in a built-in installation such as a bookcase or rack unless proper ventilation is provided or
the manufacturers instructions have been adhered to.
5.  Other Notices
Avoid exposure the N2010 to direct sunlight or high temperature.
Avoid exposure the N2010 to moisture or high humidity.
Do not attempt repair yourself. Your warranty does not cover repair or  attempted repair by anyone not authorized
by ViewSonic.
If your N2010 will not be used for a long period of time, unplug the power cord and remove the batteries from the
remote control.
ViewSonic     N2010    3
6.  Precautions
Sit at least 20 from your LCD display.
Avoid touching the screen. Skin oils are difficult to remove.
Never remove the rear cover. Your LCD display contains high-voltage parts. You may be seriously injured if you
touch them.
Avoid exposing your LCD display to direct sunlight or another heat source. Orient your LCD display away from direct
sunlight to reduce glare.
Always handle your LCD display with care when moving it.
Place your LCD display in a well-ventilated area. Do not place anything on your LCD display that prevents heat
dissipation.
Ensure the area around the LCD display is clean and free of moisture.
Do not place heavy objects on the LCD display, video cable, or power cord.
If smoke, abnormal noise, or strange odor is present, immediately switch the LCD display off and call your dealer or
ViewSonic. It is dangerous to continue using the LCD display.
 
						

							E
N
G
L
I
S
H
ANTENNA INSTALLATION INSTRUCTIONS
1. Outdoor Antenna Grounding
If  an outside antenna or cable system is connected to the product be sure the antenna or cable system is grounded
so as to provide some protection against voltage surges and built-up static charges, Article 810 of the National
Electrical Code, ANSI/NFPA 70, provides information with regard to proper grounding of the mast and supporting
structure, grounding of the lead-in wire to an antenna discharge unit, connection to grounding electrodes, and
requirements for the grounding electrode.
2. Lightning
For added protection for this product during a lightning storm, or when it is left unattended and unused for long
periods of time, unplug it from the wall outlet and disconnect the antenna or cable system. This will prevent damage
to the product due to lightning and power-line surges. Do not disconnect the antenna or the power cord during a
heavy storm lighting may strike while you are holding the cable cord, causing serious injury; turn off you LCD and
wait for the wether to improve.
3. Power Lines
An outside antenna system should not be located in the vicinity of overhead power lines or other electric light or
power circuits, or where it can fall into such power lines or circuits. When installing an outside antenna system,
extreme care should be taken to keep from touching such power lines or circuits as contact with them might be
fatal.
ViewSonic     N2010    4 Cleaning the LCD Display
Make sure the LCD Display is turned off.
Never spray or pour any liquid directly onto the screen or case.
To clean the screen:
1   Wipe the screen with a clean, soft, lint-free cloth. This removes dust and other particles.2   If still not clean, apply a small amount of non-ammonia, non-alcohol based glass cleaner onto a clean, soft,
      lint-free cloth, and wipe the screen.
To clean the case:
1   Use a soft dry cloth.
2   If still not clean, apply a small amount of a non-ammonia, non-alcohol based, mild non-abrasive
     detergent onto a clean, soft, lint-free cloth, then wipe the surface.
Disclaimer
ViewSonic® does not recommend the use of any ammonia or alcohol-based cleaners on the LCD display screen or
case. Some chemical cleaners have been reported to damage the screen and/or case of the LCD display. ViewSonic
will not be liable for damage resulting from use of any ammonia or alcohol-based cleaners.
 
						

							E
N
G
L
I
S
H
Getting Started
LCD TV Display
Power Cord
ViewSonic User Guide
Congratulations on your purchase of a ViewSonic® LCD TV display. Important!
Save the original box and all packing material for future shipping needs.
Package Contents
Your LCD TV display package includes:
29-Key Remote Control with batteries
Quick Start Guide
RCA A/V  Cable
ViewSonic     N2010    5
 
						

							E
N
G L I
S
H
Front View of the Product
Volume down
Decrease sound volume or adjust a highlighted control while in OSD menu.
ViewSonic     N2010    6
3
2
1
4
5
6
7
8
9
Volume up
Increase sound volume or adjust a highlighted control while in OSD menu.
MENU
Turn OSD menu ON/OFF.
CH down
Channel down when source is at TV or select a control while in OSD menu.
CH up
Channel up when source is at TV or select a control while in OSD menu.
ENTER
To highlight a control in OSD menu.
Power button
Remote control receiver
Power LED indicator
34567
89
12
 
						

							E
N
G L I
S
H
ViewSonic     N2010    7
Rear View of the Product
Power (AC input)
Using cable provided, connect to a power source.
Cable manager
Audio output
Connect this port to your external speaker.
AV/ S-Video signal audio input (left/right)
Connect the external audio into this jack.
YPbPr signal audio input (left/right)
Connect the external audio into this jack.
TV signal input
Connect to the antenna or cable servic
e.
S-Video input
Connect the external video device such as VCR, DVD and video game into
this jack.
AV video input
Connect the external video devices such as VCR, DVD and video game
into this jack.
I
H
G
F
E
D
C
B
A
YPbPr signal input
Connect the external video devices with component output to these jacks.J
Earphone output
ABEDFC
J
G
H
I
 
						

							E
N
G L I
S
H
ViewSonic     N2010    8
Remote Control
Turn power on/off
Select between MONO,
Stereo and  SAP when
available Display source and
channel information
Shortcut key for TV
source
Channel UP/DOWN
adjustment
Recall previous channel
Volume UP/DOWN
adjustment
Turn sound on/off Source selecting
between AV, S-Video, YPbPr and  TV
OSD Menu ON/OFF
Switch channel number key
TV Sleep time setting
Use 
ENTER to select a
control
Available in OSD menu
Use    /    arrows to
choose a control, use
    /    arrows to adjust the
selected control
 
						

							E
N
G L I
S
H
ViewSonic     N2010    9
1  Remove the battery cover by pulling then lifting the knob on the cover.
2  Insert the batteries, corresponding to the (+) and (-) markings on the battery compartment.
3  Reattach the battery cover.
1. Insert Remote Control Batteries
CAUTION
Only use the specified AAA batteries.
Do not mix new and old batteries. This may result in cracking or leakage,
which may pose a risk of fire or lead to personal injury.
Insert batteries according to (+) and (-) markings. Inserting the batteries incor-
rectly may result in cracking or leakage, which may pose a risk of fire or lead to
personal injury.
Dispose of the battery in accordance with local laws and regulations.
Keep the battery away from children and pets.
When the remote control will not to be used for an extended period, remove
the batteries.
Installation
Make sure the power is off before installing N2010.
Connect the LCD TV to TV antenna terminal or CATV box by 75-ohm coaxial cable.
2. Connecting with the antenna
RF Cable or Adapter