ViewSonic Pjd6211p Projector User Manual

							
Using the Product
Control Panel
LED
Button Function
Power (Power LED indicator)
Refer to “LED Indicator Messages”.
TEMP  (Temperature LED indicator)
Refer to “LED Indicator Messages”.
LAMP  (Lamp LED indicator)
Refer to “LED Indicator Messages”.
  /Keystone
Manually correct distorted images resulting from an angled projection.
Four directional buttons
Use four directional buttons to select items or make adjustments to your  selection.
ENTER
Enter to sub-menu and confirm the menu selection.
SOURCE
Manually select an input source.
MENU/EXIT
Display or exit the on-screen display menus.
Power
Turn the projector on or off.
13
4
6
7
5
4
2
8
9
1
2
3
4
5
6
7
8
9
PJD6211P 
9 
ViewSonic  
						

							
Connection Ports
COMPUTER IN 1
Connect image input signal (analog RGB or component) to this jack.
COMPUTER IN 2
Connect image input signal (analog RGB or component) to this jack.
MONITOR OUT
Connect to a computer display, etc.
S-VIDEO
Connect S-Video output from video equipment to this jack.
VIDEO
Connect composite video output from video equipment to this jack.
USB
This connector is for firmware update and mouse function support.
RS-232
When operating the projector via a computer, connect this to the controlling
computers RS-232C port.
AUDIO IN
Connect an audio output from video equipment to this jack.
AUDIO OUT
Connect to a speaker or other audio input equipment.
235467891
1 
1
2
3
4
5
6
7
8
9
PJD6211P 
10 
ViewSonic  
						

							
Remote Control
POWER
Turn the projector on or off.
Four directional buttons
Use four directional buttons to
select items or make adjustments
to your selection.
MENU
Display or exit the on-screen display
menus.
Enter
Confirmed selections.
Exit
Exit OSD Menu.
Keystone+ / -
Adjust image distortion caused by
tilting the projector.
Magnify
Zoom in and out the images.Freeze
Press “Freeze” to pause the screen image.
Press again to cancel the freeze function.
SourceManually select an input source.MuteCut off the sound temporarily. Press again 
to cancel the Mute function.
AutoResynchronize the projector to the
input signal from a computer. This
function is available for 
computer
mode only. Blank
Cut off the screen temporarily. Press 
again to cancel the Blank Screen 
function.
Mouse
Switch between OSD control and 
Mouse control (Apply to 
Navigation buttons, Enter/Mouse 
Left Click, and Exit/Mouse Right 
Click buttons). Volume + / -
Adjust the volume level.
ViewM
Switch in between high brightness 
performance or Accuracy color 
performance.
1
2
3
4
5
6
712
813
914
1015
11
PJD6211P 
11 
ViewSonic  
						

							
Replacing the Battery
For the first time use:
Remove the transparent insulation tape by pulling
it before use.
For battery change:
1. Push the catch to the left and remove the battery holder.
2. Remove the old Lithium coin cell and install new one (CR2025). Ensure that the side with the mark “+” is up.
3. Push the battery holder back into the remote control 
until you feel a click.
Caution
„ Risk of explosion if battery is replaced by an incorrect type.„ Dispose of used batteries according to the instructions.„ Make sure the plus and minus terminals are correctly aligned when loading a battery.
„Keep the battery out of the reach of children. „Do not recharge the battery or expose the battery to fire or water.„Do not dispose the used battery along with household waste. Dispose used 
batteries according to local regulations.
„Danger of explosion may happen if batteries are incorrectly replaced. 
Replace only with the same type recommended by the manufacturer.
„Battery should not be in or near to fire or water, keep batteries in a dark, cool 
and dry place. 
„If suspect battery leakage, wipe out the leakage and then replace a new battery. If 
the leakage adheres to your body or clothes, rinse well with water immediately.
PJD6211P 
12 
ViewSonic  
						

							
Remote Control Operation
Point the remote control at the infrared remote sensor and press a button.
„Operating the projector from
the front
„Operating the projector from 
the rear
1015
7m5m
5m
1510
7m5m
5m
„The remote control may not operate when there is sunlight or other strong
light such as a fluorescent lamp shining on the remote sensor.
„Operate the remote control from a position where the remote sensor is visible.„Do not drop the remote control or jolt it.„Keep the remote control out of locations with excessively high temperature or
humidity.
„Do not get water on the remote control or place wet objects on it.„Do not disassemble the remote control.
PJD6211P 
13 
ViewSonic  
						

							
Installation
Connecting the Projector
Audio Cable S-Video Cable
VGA Cable (D-Sub to D-Sub) Composite Video Cable
RS-232 Cable VGA (D-Sub) to HDTV (RCA) Cable
USB Cable
1
2
3
4
56
7
1
1
2
15
26
37
4
„The figure above is a sample connection. This does not mean that all of these 
devices can or must be connected simultaneously.
„The cables that come with the projector may differ from the above illustration. 
The included cables are based on actual shipment delivery.
PJD6211P 
14 
ViewSonic  
						

							
Powering On/Off the Projector
Powering On the Projector:
1. Remove the projector lens cap.
2. Complete the AC power cord and peripheral signal cable(s) connections.
3. Press   button to turn on the projector.
The projector takes a minute or so to warm up. 
4. Turn on your source (computer, notebook, DVD, etc.). The projector automatically detects your source.
„If you are connecting multiple sources to the projector simultaneously, press
the  SOURCE  button on the control panel or the Source button on the remote
control.
Warning
„Remove the lens cap first before powering on.
„Never look into the lens when the lamp is on. This can damage your eyes.
„This focal point concentrates high temperature. Do not place any object near
it to avoid possible fire hazard.
Powering Off the Projector:
1. Press   button to turn off the projector lamp. You will see a message Power
off? Press Power again appear on the screen.   
2. Press   button again to confirm.
„The cooling fans continue to operate for cooling cycle.
„When the Lamp LED begins flashing, the projector has entered stand-by mode.
„If you want to turn the projector back on, you must wait until the projector has
completed the cooling cycle and has entered stand-by mode. Once in stand-
by mode, simply press   button to restart the projector.
3. Disconnect the AC power cord from the electrical outlet and the projector.
4. Do not turn on the projector right after power off.
PJD6211P 
15 
ViewSonic  
						

							
Adjusting the Projector
Adjusting the Projector Height
The projector is equipped with an elevator foot to adjust the image height.
To raise or lower the image:
1. To raise or lower the image, press the elevator button and raise or lower the frontof the projector. Release the button to lock the adjustment.
2. To level the image on the screen, turn th e tilt-adjustment foot to fine-tune the 
height.
Adjusting the Projector Zoom and Focus
1. Focus the image by rotating the focus  ring. A still image is recommended for focusing.2. Adjust the image by sliding the zoom ring. 
Elevator button
Elevator foot
Tilt-adjustment foot
„To avoid damaging the projector, make sure that the elevator foot and tilt-
adjustment foot are fully retracted before placing the projector in its carrying 
case.
Focus ring Zoom ring
PJD6211P 
16 
ViewSonic  
						

							
Adjusting Projection Image Size
Refer to the graphic and table below to determine the screen size and projection distance.
Screen size
Diagonal  (inch) 4 : 3 Screen
Wide Tele
Projection distance Projection distance
minchminch
40 1.57 61.76 1.73 67.93
50 1.96 77.20 2.16 84.92
60 2.35 92.64 2.59 101.90
70 2.75 108.07 3.02 118.88
80 3.14 123.51 3.45 135.86
90 3.53 138.95 3.88 152.85
100 3.92 154.39 4.31 169.83
120 4.71 185.27 5.18 203.80
150 5.88 231.59 6.47 254.75
200 7.84 308.78 8.63 339.66
250 9.80 385.98 10.78 424.58
300 11.76 463.18 12.94 509.49
40
60
100
120
200
Wide: 1.57m Tele: 1.73m
Wide: 2.35m   Tele: 2.59m
Wide: 3.92m Tele: 4.31m
Wide: 4.71m Tele: 5.18m
Wide: 7.84m Tele: 8.63m
„Position the projector in a horizontal position; other positions can cause heat 
build-up and damage to the projector.
„Keep a space of 30 cm or more between the sides of the projector.„Do not use the projector in a smoky environment. Smoke residue may build-
up on critical parts and damage the projector or its performance.„Consult with your dealer for special installation such as suspending from a 
ceiling.
PJD6211P 
17 
ViewSonic  
						

							
Menu Operation
The projector has multilingual on-screen display menus that allow you to make image
adjustments and change a variety of settings.
5P
5P
PJD6211P 
18 
ViewSonic