ViewSonic Pjd6383s Projector User Manual

							46
Menu operation
Menu system
Please note that the on-screen display (OSD) menus vary according to the signal type 
selected.
The menu items are available when the projector detects at least one valid signal. If there is 
no equipment connected to the projector or no signal detected, limited menu items are 
accessible.
Main menu Sub-menu Options
1.
DISPLAY
Screen ColorOff/Blackboard/
Greenboard/Whiteboard
Aspect RatioAuto/4:3/16:9/
16:10 (
 only)
Keystone
Position
Phase
H. Size
Zoom
3D Sync  TI 3D DLP Link/Off
3D Sync Invert Disable/Invert
Color 
ManagementPrimary Color R/G/B/C/M/Y
Hue
Saturation
Gain
2.
PICTURE
Color ModePC source: Brightest/PC/ViewMatch/Movie/
Dynamic PC/Dynamic Movie/User 1/User 2
Video source: Brightest/Gaming/ViewMatch/
Movie/Dynamic Movie/User 1/User 2
Reference ModePC source: Brightest/PC/ViewMatch/Movie/
Dynamic PC/Dynamic Movie
Video source: Brightest/Gaming/ViewMatch/
Movie/Dynamic Movie
Brightness
Contrast
Color
Tint
Sharpness
Brilliant Color On/Off
Color Temperature T1/T2/T3/T4
Save Settings
 PJD5226w/
PJD6653ws/
PJD6683wsPJD6553w/
PJD6 3w/65
PJD6683w/ 
						

							47
Main menu Sub-menu Options
3. SOURCE
Quick Auto Search Off/On
Color Space Conversion (PJD6223/
PJD6253/PJD6353/PJD6353s/PJD6383/
only)
RGB/YUV/Auto
DynamicEco TimerDisable/5 min/10 min/15 
min/30 min
Smart Restart Off/On
PatternPJD5126/PJD5226/PJD5226w: Off/On
PJD6223/PJD6253/PJD6353/PJD6353s/PJD6383/PJD6383s: 
01/02/03/04/05/User
PJD6553w/PJD6653w/PJD6653ws/PJD6683w/PJD6683ws: 
01/02/03/04/User
My Button
Projection (Projector Position)/3D Sync/Lamp 
Mode/DCR/Closed Caption/Auto Off (Auto Power 
Off)/Message/Screen Color/Screen Capture 
(PJD6223/PJD6253/PJD6353/PJD6353s/PJD6383/PJD6383s/PJD6553w/
PJD6653w/PJD6653ws/PJD6683w/PJD6683ws only)/Information
4.
SYSTEM
SETUP:
Basic
LanguageMulti-language OSD 
selection
Projector PositionFront Table/Rear Table/
Rear Ceiling/Front Ceiling
Auto Power OffDisable/5 min/10 min/20 
min/30 min/40 min/50 min/
60 min
Blank TimerDisable/5 min/10 min/15 
min/20 min/25 min/30 min
Panel Key Lock On/Off
Splash ScreenBlack/Blue/ViewSonic/
Screen Capture (PJD6223/
PJD6253/PJD6353/PJD6353s/
PJD6383/PJD6383s/PJD6653w/
PJD6553w/PJD6653ws/PJD6683w 
Off
Screen Capture (PJD6223/PJD6253/PJD6353/PJD6353s/PJD6383/PJD6383s/
PJD6653w/ PJD6683w  only)
PJD6383s/PJD6553w/PJD6653w/PJD6653ws/ 
PJD66 w/PJD66 ws83 83
PJD6683ws
only)
PJD6553w/ PJD6653ws/ /PJD6683ws 
						

							48
Main menu Sub-menu Options
4.
SYSTEM
SETUP:
Basic
Message On/Off
LAN Control 
Settings
(PJD6223/PJD6253/
PJD6353/PJD6353s/
PJD6383/PJD6383s/
PJD6553w/
PJD6653w/
PJD6653ws/
PJD6683ws only)DHCP On/Off
Projector IP Address
Subnet Mask
Default Gateway
DNS Server
Apply
Standby 
SettingsPower Saving On/Off
Active VGA Out On/Off
Active Audio Out On/Off
Quick Power Off On/Off
5.
SYSTEM
SETUP:
Advanced
High Altitude Mode On/Off
DCR On/Off
Audio SettingsMute On/Off
Volume
Menu SettingsMenu Display Time5 sec/10 sec/15 sec/20 sec/
25 sec/30 sec
Menu PositionCenter/Top-Left/Top-Right/
Bottom-Left/Bottom-Right
Closed CaptionClosed Caption 
EnableOn/Off
Caption Version CC1/CC2/CC3/CC4
Lamp SettingsLamp Mode Normal/Economic
Reset Lamp Timer
Equivalent Lamp 
Hour
Presentation 
TimerTimer Period 1~240 minutes
Timer DisplayAlways/1 min/2 min/3 min/
Never
Timer PositionTop-Left/Bottom-Left/Top-
Right/Bottom-Right
Timer Counting 
DirectionCount Down/Count Up
Sound Reminder On/Off
Start Counting/Off
Security 
SettingsChange Password
Power On Lock On/Off
Remote Control Code A/B
Reset All Settings On/Off
PJD6683w 
						

							49
Main menu Sub-menu Options
6. 
INFORMATIONCurrent System Status•Source
•Color Mode
•Resolution
•Color System
•Equivalent Lamp Hour
•MAC Address (PJD6223/PJD6253/
PJD6353/PJD6353s/PJD6383/PJD6383s/
PJD6553w/PJD6653w/PJD6653ws/
PJD6683w  only)
/PJD6683ws 
						

							50
Description of each menu
Function Description
Screen ColorCorrects the projected picture’s color when the projection surface 
is not white. See "Using Screen Color" on page 33 for details.
Aspect RatioThere are three options to set the image's aspect ratio depending 
on your input signal source. See "Selecting the aspect ratio" on 
page 30 for details.
KeystoneCorrects any keystoning of the image. See "Correcting keystone" 
on page 29 for details.
Position
Displays the position adjustment page. To move the projected 
image, use the directional arrow keys. The values shown on the 
lower position of the page change with every key press you made 
until they reach their maximum or minimum.
Phase
Adjusts the clock phase to reduce image 
distortion.
H. SizeAdjusts the horizontal width of the image.
ZoomMagnifies or reduces the projected image. See "Magnifying and 
searching for details" on page 29 for details.
3D Sync
This projector features a 3D function which enables you to enjoy 
the 3D movies, videos, and sporting events in a more realistic 
way by presenting the depth of the images.
This function is not available when video source is detected 
for the PJD5126/PJD5226/PJD5226w.
You need to wear a pair of 3D glasses to view the 3D images.
• TI 3D DLP Link:
Enables projector for TI 3D DLP Link.
• Off: 
Disables 3D.
When the 3D Sync function is on:
• The brightness level of the projected image will decrease.
• The Color Mode cannot be adjusted.
• The Keystone can only be adjusted within limited degrees.
• The Zoom can only magnify the pictures to limited sizes.
3D Sync 
InvertWhen you discover the inversion of the image depth, enable this 
function to correct the problem. (For TI 3D DLP Link only)
Color
ManagementSee"Color Management" on page 35 for details.
1. DISPLAY menu 
						

							51
Function Description
Color ModePre-defined picture modes are provided so you can optimize your 
projector image set-up to suit your program type. See "Selecting a 
picture mode" on page 32 for details.
Reference
ModeSelects a picture mode that most suits your need for the image 
quality and further fine-tune the image based on the selections 
listed on the same page below. See "Setting the User 1/User 2 
mode" on page 33 for details.
BrightnessAdjusts the brightness of the image. See "Adjusting Brightness" on 
page 34 for details.
ContrastAdjusts the degree of difference between dark and light in the 
image. See "Adjusting Contrast" on page 34 for details.
ColorAdjusts the color saturation level -- the amount of each color in a 
video image. See "Adjusting Color" on page 34 for details.
Tint
Adjusts the red and green color tones of the image. See "Adjusting
Tint" on page 34 for details.
The function is only available when Video or S-Video with 
NTSC system is selected.
SharpnessAdjusts the image to make it look sharper or softer. See "Adjusting
Sharpness" on page 34 for details.
Brilliant 
ColorAdjusts white peaking while maintaining correct color presentation. 
See"Adjusting Brilliant Color" on page 34 for details.
Color
TemperatureSee"Selecting a Color Temperature" on page 34 for details.
Save 
SettingsSaves the settings made for the User 1 or User 2 mode.
2. PICTURE menu 
						

							52
Function Description
Quick Auto 
SearchSee"Switching input signal" on page 27 for details.
Color Space 
ConversionSee"Changing Color Space" on page 27 for details.
DynamicEco 
TimerAllows the projector to decrease the power consumption 
automatically if no input signal is detected after a set period of time.
It takes some time to initiate this function. Make sure the 
projector has been turned on for more than 4 minutes.
Smart 
Restart
SelectingOn enables you to restart the projector immediately 
within 150 seconds after turning it off. After 150 seconds, if the 
projector is not turned on again, it will directly enter the standby 
mode.
•It takes some time to initiate this function. Make sure the 
projector has been turned on for more than 4 minutes.
If the projector is resumed by using the Smart Restart 
feature, this function can be executed immediately. 
•When On is selected, the Quick Power Off function will be 
automatically set to “On”.
Pattern
The projector can display several test patterns. It helps you adjust 
the image size and focus and check that the!projected image is free 
from distortion.
Selecting User displays the picture you saved as Screen 
Capture.
My ButtonSets a hotkey on remote control.
3. SOURCE menu 
						

							53
Function Description
LanguageSets the language for the On-Screen Display (OSD) menus. See 
"Using the menus" on page 23 for details.
Projector 
PositionThe projector can be installed on a ceiling or behind a screen, or 
with one or more mirrors. See "Choosing a location" on page 12
for details.
Auto Power 
OffAllows the projector to turn off automatically if no input signal 
is detected after a set period of time. See "Setting Auto Power 
Off" on page 57 for details.
Blank TimerSets the image blank time when the Blank feature is activated, 
once elapsed the image will return to the screen. See "Hiding the 
image" on page 37 for details.
Panel Key 
LockDisables or enables all panel key functions except POWER
on the projector and keys on the remote control. See "Locking 
control keys" on page 37 for details.
Splash 
ScreenAllows you to select which logo screen will be displayed during 
projector start-up.
Screen
Capture Captures and stores the projected picture as Screen Capture.
See"Creating your own startup screen" on page 38 for details.
MessageSelectingOn displays the current information on the screen 
when the projector is detecting or searching for a signal.
LAN Control 
SettingsSee"Controlling the projector through a LAN environment" on 
page 39 for details.
Standby 
SettingsSee"Using the projector in standby mode" on page 45 for 
details.
High Altitude 
ModeA mode for operation in high altitude areas. See "Operating in a 
high altitude environment" on page 37 for details.
DCR
Enables or disables the DCR (Dynamic Contrast Ratio) function. 
SelectingOn enables the function and the projector will 
automatically switch the lamp mode between normal and 
economic modes according to the input image detected.
This function is only available when a PC source is in use.
After enabling DCR, frequent lamp mode switching may 
shorten lamp life and noise level will vary during operation.
4. SYSTEM SETUP: Basic menu
II
5.  
						

							54
Function Description
Audio
Settings
The sound adjustments made as below will have an effect on the 
projector speaker. Be sure you have made a correct connection to 
the projector audio input/output jacks. See "Connection" on page 
17 for more details.
Mute
Mutes the sound received from AUDIO IN 1 and AUDIO IN 2 
(L/R).
Volume
Adjusts the sound level received from AUDIO IN 1 and AUDIO 
IN 2 (L/R).
Menu 
Settings
Menu Display Time
Sets the length of time the OSD will remain active after your last 
key press. The range is from 5 to 30 seconds in 5-second 
increments.
Menu Position
Sets the On-Screen Display (OSD) menu position.
Closed 
Caption
Closed Caption Enable
Activates the function by selecting On when the selected input 
signal carries closed captions.
• Captions: An on-screen display of the dialogue, narration, 
and sound effects of TV programs and videos that are closed 
captioned (usually marked as "CC" in TV listings).
This function is only available when a Composite video or 
S-Video input signal is selected and its system format is 
NTSC.
Caption Version
Selects a preferred closed captioning mode. To view captions, 
select CC1, CC2, CC3, or CC4 (CC1 displays captions in the 
primary language in your area).
Lamp 
Settings
Lamp Mode 
See"Setting Lamp Mode as Economic" on page 57 for details.
Reset Lamp Timer
See"Resetting the lamp timer" on page 61 for details.
Equivalent Lamp Hour
See"Getting to know the lamp hour" on page 57 for details on 
how the total lamp hour is calculated.
Presentation 
TimerReminds the presenter to finish the presentation within a certain 
time frame. See "Setting the presentation timer" on page 36 for 
details.
5. SYSTEM SETUP: Advanced menu 
						

							55
Function Description
Security
SettingsSee"Utilizing the password function" on page 24 for details.
Remote
Control CodeSee"Remote control code" on page 9 for details.
Reset All 
SettingsReturns all settings to the factory preset values.
The following settings will still remain: Phase, H. Size, User 
1, User 2, Language, Projector Position, High Altitude 
Mode, Security Settings.
Current
System 
Status
Source
Shows the current signal source.
Color Mode
Shows the selected mode in the PICTURE menu.
Resolution
Shows the native resolution of the input signal.
Color System
Shows input system format, NTSC, PAL, SECAM, or RGB.
Equivalent Lamp Hour
Displays the number of hours the lamp has been used.
MAC Address
Shows the MAC Address of your projector.
MAC Address stands for Media Access Control Address, 
which is a physical layer address used to uniquely identify 
a network node.
5. SYSTEM SETUP: Advanced menu
6. INFORMATION menu