ViewSonic Pjd6531w Projector User Manual

 EN-18
Menu Operation
The projector has multilingual on-screen display menus that allow you to make image
adjustments and change a variety of settings. 

EN-19
*1 Adjustable range and default setting vary depending on signal type.
*2 This function is only available when the projector is installed an optional filter cover. 

 EN-20
How to operate
1. Press the MENU button to open the OSD menu.
2. When OSD is displayed, use S / T to select any feature in the main menu.
3. After selecting the desired main menu item, press X to enter sub-menu for feature
setting.
4. Use 
S / T to select the desired item and adjust the settings with W / X.
5. Press the MENU button, the screen will return to the main menu.
6. To exit OSD, Press the MENU button again. The OSD menu will close and the projector
will automatically save the new...

EN-21
Effect the represent of dark scenery. With greater gamma value, dark scenery will look
brighter.
3D Sync
„Off: Disable 3D function
„3D-Vision: For NVIDIA 3D Vision application
„DLP-LINK: For TI 3D DLP-LINK application
3D Sync Invert (for TI 3D DLP-LINK only)
„On: Invert left and right frame contents.
„Off: Default frame contents.
Computer Image (Computer Mode)
FrequencyAdjust the timing of the projector relative to the computer.
TrackingAdjust the phase of the projector relative to the computer.
H...

 EN-22
ProjectionAdjust the picture to match the orientation of the projector: upright or upside-down, in front of
or behind the screen. Invert or reverse the image accordingly.
Signal TypeSpecify the source to the COMPUTER IN 1/COMPUTER IN 2 terminal that you wish to
project.
„Auto : Automatically detect the input signal type from COMPUTER IN 1 and 
COMPUTER IN 2 terminals.
„RGB : For VGA signal
„YCbCr/YPbPr:For component signal
Lamp HoursDisplay the lamp’s elapsed operating time (in hours).
Lamp Hours...

EN-23
Set or change the password. When the password function is added, image projection will
require to input the preset password when turning on the projector.
Screen CaptureCapture the current projection screen as a start-up screen.
Screen Capture DeleteDelete the captured projection screen.
Start-up ScreenSelect start-up screen when the projector is powered on or when no signal is input.
User is the screen that you captured.
ZoomZoom in and out the images.
Text shotUsing command codes, text messages...

 EN-24
Group NameDisplay group name.
Projector  NameDisplay projector name.
IP AddressNumerical address to identify networked computers. This function can only be used when
DHCP is set to No.
„The IP Address is the number that identifies this projector on the network. You cannot 
have two devices with the same IP Address on the same network.
„The IP Address “0.0.0.0” is prohibited.
Subnet MaskA numeric value to define the number of bits used for a network address of a divided
network (or subnet) in an IP...

EN-25
Network Control
This feature provides the ability to remotely control and manage the projector through
the network.
Preparation:
1. Connect one end of the internet cable to the Network Control connector on the 
projector.
2. Connect the other end of the internet cable to an available RJ-45 connector on 
your computer.
3. Turn on your projector and computer.
There are two ways to connect to the network control:A. Auto IP address setting (DHCP : Yes):
1. Enable DHCP from the projector OSD, under...

 EN-26
2. Start browser in PC and specify following URL, then click “Go” button.
„URL: http://(Projector IP address)/
„For example, if projector IP address is 169.254.1.1, specify URL: http://
169.254.1.1/
3. If connection succeeds, the login screen is displayed. Enter your User name and 
Password and click “OK”. Below are the factory default settings for administrator, 
user and passwords.
)For setting passwords, please go to Network Control page > Password.
Item User name Password
Administrator Admin...

EN-27
B. Manual IP address setting (DHCP: No):
1. Set IP Address and Subnet Mask under Network Config.
„IP Address: Numerical address to identify networked computers.
„Subnet Mask: A numeric value to define the number of bits used for a 
network address of a divided network (or subnet) in an IP Address.
„Gateway: A server (or router) to communicate across networks (subnets) 
that are divided by Subnet Mask.
2. From your computer, go to Start > Settings > Network and Dial-up 
Connections > Local Area...