ViewSonic Pjd6531w Projector User Manual

							 EN-38
Tips for solving web page problems:
If your web page is not running smoothly, please follow below steps to set the browser.
1. Go to Tools > General and click Settings. 
						

							EN-39
2. Click Every visit to the page and OK.
3. Click OK to exit Internet Properties. 
						

							
 EN-40
Maintenance
The projector needs proper maintenance. You should keep the lens clean as dust, dirt
or spots will project on the screen and diminish image quality. If any other parts need
replacing, contact your dealer or qualified service personnel. When cleaning any part
of the projector, always switch off and unplug the projector first.Warning
Never open any of the covers on the projector. Dangerous electrical voltages
inside the projector can cause severe injury. Do not attempt to service this
product yourself. Refer all servicing to qualified service personnel.
Cleaning the Lens
Gently wipe the lens with lens cleaning paper. Do not touch the lens with your hands.
Cleaning the Projector Housing
Gently wipe with a soft cloth. If dirt and stains are not easily removed, use a soft cloth
damped with water, or water and neutral detergent, and wipe dry with a soft, dry cloth.
„Turn off the projector and remove the AC power cord from the power outlet 
before beginning maintenance work.
„Make sure the lens is cool before cleaning.„Do not use detergents or chemicals other than those noted above. Do not use 
benzene or thinners.
„Do not use chemical sprays.„Use a soft cloth or lens paper only. 
						

							EN-41
Replacing the Lamp
As the projector operates over time, the brightness of the projector lamp gradually
decreases and the lamp becomes more susceptible to breakage. We recommend
replacing the lamp if a warning message is displayed. Do not attempt to replace the
lamp yourself. Contact the qualified service personnel for replacement.
„The lamp is extremely hot right after turning off the projector. If you touch the 
lamp, you may scald your finger. When you replace the lamp, wait for at least 
45 minutes for the lamp to cool down.
„Do not touch the lamp glass at any time. The lamp may explode due to 
improper handling, including the touching of the lamp glass.
„Lamp lifetime may differ from lamp to lamp and according to the environment 
of use. There is no guarantee of the same lifetime for each lamp. Some lamps 
may fail or terminate their lifetime in a shorter period of time than other similar 
lamps.
„A lamp may explode as a result of vibration, shock or degradation as a result of 
hours of use as its lifetime draws to an end. Risk of explosion may differ 
according to the environment or conditions in which the projector and lamp are 
being used.
„Wear protective gloves and eyeglasses when fixing or detaching the lamp.„Faster on-off-cycles will damage the lamp and reduce lamp life. Wait at least 
for 5 minutes to turn off the projector after powering on.
„Do not operate the lamp in proximity to paper, cloth, or other combustible 
material nor cover it with such materials.
„Do not operate the lamp in an atmosphere containing an inflammable 
substance, such as thinner.
„Thoroughly ventilate the area or the room when operating the lamp in an 
oxygen atmosphere (in the air). If ozone is inhaled, it could cause headaches, 
nausea, dizziness, and other symptoms.
„The inorganic mercury is involved in the lamp. If the lamp bursts, the mercury 
inside the lamp will be exposed. Leave the area immediately if the lamp 
shatters while being operated and ventilate the area for at least 30 minutes in 
order to avoid the inhalation of mercury fumes. Otherwise it could be harmful to 
user’s health. 
						

							 EN-42
1. Turn off the projector.
2. If the projector is installed in a ceiling mount, remove it
3. Unplug the power cord.
4. Loosen the screw in the side of the lamp cover and remove the cover.
5. Remove the screws from the lamp module, raise the handle, and lift out the 
module.
6. Insert the new lamp module into the projector and tighten the screws.
7. Replace the lamp cover and tighten the screw.
8. Turn on the projector.  If the lamp does not turn on after the warm-up period, try 
reinstalling the lamp.
9. Reset the lamp hour. Refer to the “Setting” menu.
„Dispose the used lamp according to local regulations.„Ensure that screws are tightened properly. Screws not tightened fully may 
result in injury or accidents.
„Since the lamp is made of glass, do not drop the unit and do not scratch the 
glass.
„Do not reuse the old lamp. This could cause the lamp to explode.„Be sure to turn off the projector and unplug the AC power cord before 
replacing the lamp.
„Do not use the projector with the lamp cover removed. 
						

							EN-43
Specifications
Display system Single 1.651cm / 0.65 DLP panel
Resolution WXGA (1280 x 800)
Zoom 1.2X
F/No. 2.55
Focal length 21 - 25.6mm
Screen size 101.6cm ~ 381cm / 40” – 150”
Lamp 230W
Input terminal D-Sub 15-pin x 2, S-VIDEO x 1, VIDEO x 1, Audio signal input 
(3.5 mm stereo mini jack) x 2, HDMI x 1
Output terminal D-Sub 15 pin x 1,  Audio signal output (3.5 mm stereo mini jack) x 
1, 12-Vdc trigger output x 1
Control terminal RS-232 x 1, USB x 1, LAN x 1
Speaker 5 watt x 2
Video compatibility NTSC, NTSC 4.43
PAL, PAL-N, PAL M
SECAM, HDTV (480p, 576p, 720p, 1080i/p), Composite video
Scanning frequency
Horizontal frequency
Vertical frequency31 - 80 KHz
50 - 120 Hz
Environment Operating:
Temperature: 0°C to 40°C
Humidity: 30%-85%
Storage:
Temperature: -20°C to 60°C
Humidity: 30%-85%
Power requirement AC 100-240 V, 50 - 60 Hz, 3.7A
Power consumption 290 W
Dimension (W x D x H) 279.5 x 218 x 105 mm (11.0 x 8.6 x 4.1 inches)
Weight 2.7 kg (6lb)
Note: Design and Specifications are subject to change without prior notice. 
						

							 EN-44
Appendix
LED Indicator Messages
LED Type  Color  Status Meaning
Power  LED Blue Solid
The projector is  in standby 
mode. Lamp LED Off  Off 
Temp LED  Off  Off 
Power  LED Blue Solid
Powering up Lamp LED Off  Off 
Temp LED  Off  Off 
Power  LED Blue Solid
Normal operation Lamp LED Off  Off 
Temp LED  Off  Off 
Power  LED Blue Flash
Power-down Lamp LED Off  Off 
Temp LED  Off  Off 
Power  LED Blue Solid (Full brightness)
The projector system has some 
problems with its fans, so the 
projector cannot start up.  Lamp LED Red Solid
Temp LED  Red Flash
Power  LED Blue Solid (Full brightness)
The lamp is in good condition 
and is projecting at maximum 
brightness.  Lamp LED Off  Off 
Temp LED  Off  Off 
Power  LED Blue Solid (Full brightness) The lamp has reached its end 
of life and must be changed 
soon. The lamp will continue to 
operate until it fails . Change 
the lamp. If the lamp is off, then  
the ballast will become 
malfunction.  Lamp LED Off  Solid
Temp LED  Off  Solid
Power  LED Blue Flash  (Full 
brightness)The projector is shutting and 
the fan motor is cooling the 
lamp for shutdown. Do not 
unplug the power cord or turn 
the power off before the Lamp 
LED changes to flashing. The 
fan motor will turn off when the 
lamp has cooled.  Lamp LED Red Solid
Temp LED  Red Solid
Power  LED Blue Solid (Full brightness) Temperature is too high. The 
lamp will turn off. The fan motor 
is cooling the lamp.  Lamp LED Red Flash
Temp LED  Red Off 
Power  LED Off  Off  The lamp ignition failed. If 
temperature is too high, the 
fans will cool the lamp. Lamp LED Red Solid
Temp LED  Red Solid 
						

							EN-45
Compatibility Modes
Computer: 
Compatibility Resolution H-Sync [KHz] V-Sync [Hz]
VGA 640 x 480 24.6 50.0
31.5 59.9
37.9 72.8
37.5 75.0
43.3 85.0
640 x 480 @ 120Hz 61.9 119.5
720 x 400 31.5 70.0
37.9 85.0
SVGA 800 x 600 31.0 50.0
35.2 56.0
37.9 60.3
48.1 72.0
46.9 75.0
53.7 85.1
76.3 120.0
800 x 600 @ 120Hz 76.3 120.0
XGA 1024 x 768 48.4 60.0
56.5 70.1
60.0 75.0
68.7 85.0
97.6 120.0
1024 x 768 @ 120Hz  97.6 120.0
1152 x 864 67.5 75.0
1280 x 960 60.0 60.0
85.9 85.0
SXGA 1280 x 1024 64.0 60.0
80.0 75.0
1280 x 960 64.7 60.0
75.0 75.0
1280 x 1024 64.0 60.0
80.0 75.0
14460 x 1050 64.7 60.0
1600 x 1200 75.0 60.0
WXGA VESA 
60Hz1280 x 800 49.7 59.8 
						

							 EN-46
Video:  
Signal Horizontal Frequency (kHz) Vertical Frequency (Hz)
1080i 33.8 60.0
1080i 28.1 50.0
1080p 67.5 60.0
1080p 56.3 50.0
720p 45.0 60.0
720p 37.5 50.0
576p 31.3 50.0
576i 15.8 50.0
480p 31.5 60.0
480i 15.8 60.0 
						

							EN-47
Troubleshooting
Refer to the symptoms and measures listed below before sending the projector for
repairs. If the problem persists, contact your local reseller or service center. Please
refer to LED Indicator Messages as well.
Start-up problems
If no lights turn on:
„Be sure that the power cord is securely connected to the projector and the other endis plugged into an outlet with power.
„Press the power button again.
„Unplug the power cord and wait for a short while, then plug it in and press the powerbutton again.
Image problems
If the searching source is displayed:
„Press the SOURCE button on the control panel or the Source button on the remote
control one or more times to select another active input source.
„Be sure the external source is turned on and connected.
„For a computer connection, ensure your notebook computer’s external video port isturned on. Refer to the computer manual.
If the image is out of focus:
„Be sure the lens cover is removed.
„While displaying the on-screen menu, adjust the focus ring. (The image size shouldnot change; if it does, you are adjusting the zoom, not the focus.)
„Check the projection lens to see if it needs cleaning.
If the image is flickering or unstable for a computer connection:
„Press the Auto button on the remote control.
„Press the MENU button, go to Computer Image and adjust Frequency or
Tracking.
Remote control problemsIf the remote control does not operate:
„Be sure nothing is blocking the remote control receiver on the front of the
projector. Use the remote control within the effective range.
„Aim the remote control at the screen or at the front or back of the projector.
„Move the remote control so it is more directly in front of or behind the projector andnot as far to the side.