ViewSonic Pro8200 Projector User Manual

ViewSonic  Pro8200 29
Video/Audio
Frequency
Adjust the timing of the projector relative to the computer.
Tracking
Adjust the phase of the projector relative to the computer.
H Position (Horizontal Position)
Adjust the image left or right within the projection area.
V Position (Vertical Position)
Adjust the image up or down within the projection area.
Overscan
Remove noise around the video image.
Noise Reduction
Reduce temporal and/or spatial noise in the image.
Audio Setting
Allow you to enter the Audio...

ViewSonic  Pro8200 30
Aspect Ratio
Select how the picture fits on the screen:
„Auto : Scales an image proportionally to fit the projectors native resolution in its 
horizontal or vertical width.
„4:3 : Scales an image so that it is displayed in the center of the screen with a 4:3 
aspect ratio.
„16:9 : Scales an image so that it is displayed in the center of the screen with a 16:9 
aspect ratio.
„16:10 : Scale an image so that it is displayed in the center of the screen with a 16:10 
aspect ratio....

ViewSonic  Pro8200 31
Quick Power On
Enable the projector to turn on automatically after the power cord has been connected 
and power has been applied.
Quick Power Off
Enable the projector to turn off quickly.
DC 12V Trigger
Enable or disable to trigger external devices such as an electric screen.
Option
Password
Set or delete the password. When the password function is added, image projection will 
require to input the preset password when turning on the projector.
Blank Screen
Blank the screen...

ViewSonic  Pro8200 32
Allow user to define a short cut key on the remote control, and the function item is selected 
in OSD menu.
Information
Input Source
Display the current input source.
Resolution
Display current input source resolution.
H. Frequency
Display current image horizontal  frequency.
V. Frequency
Display current image vertical frequency.
Filter Hours
Display the filter’s elapsed operating time (in hours).
„When Filter Mode is turned on, the Filter Hours also turns on automatically.
Filter...

ViewSonic  Pro8200 33
Maintenance
The projector needs proper maintenance. You should keep the lens clean as dust, dirt 
or spots will project on the screen and diminish image quality. If any other parts need 
replacing, contact your dealer or qualified service personnel. When cleaning any part 
of the projector, always switch off and unplug the projector first.
Warning
Never open any of the covers on the projector. Dangerous electrical voltages 
inside the projector can cause severe injury. Do not...

ViewSonic  Pro8200 34
Replacing the Lamp
As the projector operates over time, the brightness of the projector lamp gradually 
decreases and the lamp becomes more susceptible to breakage. We recommend 
replacing the lamp if a warning message is displayed. Do not attempt to replace the 
lamp yourself. Contact the qualified service personnel for replacement.
„The lamp is extremely hot right after turning off the projector. If you touch the 
lamp, you may scald your finger. When you replace the lamp, wait...

ViewSonic  Pro8200 35
1. Turn off the projector.
2. If the projector is installed in a ceiling mount, remove it
3. Unplug the power cord.
4. Loosen the screw in the side of the lamp cover and remove the cover.
5. Remove the screws from the lamp module, raise the handle, and lift out the 
module.
6. Insert the new lamp module into the projector and tighten the screws.
7. Replace the lamp cover and tighten the screw.
8. Turn on the projector.  If the lamp does not turn on after the warm-up period, try...

ViewSonic  Pro8200 36
Specifications
Display system Single 0.65 DLP panel
Resolution 1080p (1920 × 1080 pixels)
Zoom 1.5X
F/No. 2.41 - 2.97
Focal length 20.72 - 31mm
Screen size 30” - 300”
Lamp 230W
Input terminal D-Sub 15-pin x 2, S-Video x 1, Video x 1, Audio signal input (3.5 
mm stereo mini jack) x 2, HDMI x 2, Component RCA jack x 1, 
RCA audio jack (L/R) x 1, 3.5 mm Mic input x1, USB  A type x1 
(supports firmware update)
Output terminal D-Sub 15 pin x 1,  Audio signal output (3.5 mm stereo mini...

ViewSonic  Pro8200 37
Dimensions
 334.6 mm (W) x 264.5 mm (D) x 109.5 mm (H)
Ceiling mount installation
264.5
109.5334.6
64.5
84.9
174227
103
Ceiling mount screws:
M4 x 8 (Max. L = 8 mm)
Unit: mm 

ViewSonic  Pro8200 38
Appendix
LED Indicator Messages
LED type Color Status Meaning
Power LED Blue Solid Lamp life end
Lamp LED Red Flash
Temp LED Red Flash
Power LED Blue Solid Standby mode when green mode is 
turned on.
Lamp LED Red Off
Temp LED Red Off
Power LED Blue Flash Standby mode when green mode is 
turned off.
Lamp LED Red Off
Temp LED Red Off
Power LED Blue Solid Powering up
Lamp LED Red Off
Temp LED Red Off
Power LED Blue Solid Normal operation
Lamp LED Red Off
Temp LED Red Off
Power LED Blue...