ViewSonic VA1912w Manual

							ViewSonicVA1912w/VA1912wb 8
Using the LCD Display
Setting the Timing Mode
Setting the timing mode is important for maximizing the quality of the screen image and
minimizing eye strain. The timing mode consists of the resolution (example 1440 x 900) and
refresh rate (or vertical frequency; example 60 Hz). After setting the timing mode, use the
OSD (On-screen Display) controls to adjust the screen image.
For the best picture quality set your LCD display timing mode to:
VESA 1440 x 900 @ 60Hz.
To set the Timing Mode:
1. Set the resolution: Right-click on the Windows desktop > Properties > Settings > set the 
resolution.
2. Set the refresh rate: See your graphic cards user guide for instructions.
WARNING: Do not set the graphics card in your computer to exceed the maximum refresh
rate of 75Hz; doing so may result in permanent damage to your LCD display
.
OSD and Power Lock Settings
•OSD Lock: Press and hold [1] and the up arrow S for 10 seconds. If any buttons are
pressed the message OSD Locked will display for 5 seconds.
•OSD Unlock: Press and hold [1] and the up arrow S again for 10 seconds.
•Power Button Lock: Press and hold [1] and the down arrow T for 10 seconds. If the
power button is pressed the message Power Button Locked will display for 5 seconds. With
or without this setting, after a power failure, your LCD display’s power will automatically
turn ON when power is restored.
•Power Button Unlock: Press and hold [1] and the down arrow T again for 10 seconds.
 
						

							ViewSonicVA1912w/VA1912wb 9
Adjusting the Screen Image
Use the buttons on the front control panel to display and adjust the OSD controls which display 
on the screen. The OSD controls are explained at the top of the next page and are defined in 
“Main Menu Controls” on page 11.
Main Menu
with OSD controls
Front Control Panel
shown below in detail
Scrolls through menu options and 
adjusts the displayed control.
Also a shortcut to display the Contrast 
adjustment control screen.
Displays the control screen 
for the highlighted control.
Also toggles between two 
controls on some screens.
Power light
Green = ON
Orange = Power Saving
Standby Power 
On/Off
Displays the Main Menu or
exits the control screen and
saves adjustments.
Audio Mute
button turns
the sound off
 
						

							ViewSonicVA1912w/VA1912wb 10 Do the following to adjust the display setting:
1.To display the Main Menu, press button [1].
NOTE: All OSD menus and adjustment screens disappear automatically after about 15 
seconds. This is adjustable through the OSD timeout setting in the setup menu.
2.To select a control to adjust, pressSorTto scroll up or down in the Main Menu.
3.After the desired control is selected, press button [2]. A control screen like the one shown 
below appears.
4.To adjust the setting, press the up S or down T buttons.
5.To save the adjustments and exit the menu, press button [1] twice.
The following tips may help you optimize your display:
• Adjust the computers graphics card so that it outputs a 1440 x 900 @ 60Hz video signal to
the LCD display. (Look for instructions on “changing the refresh rate” in the graphics cards
user guide.)
• If necessary, make small adjustments using H. POSITION and V. POSITION until the
screen image is completely visible
. (The black border around the edge of the screen should
barely touch the illuminated “active area” of the LCD display.)
The command line at the bottom of the
control screen tells what to do next from
this screen. You can toggle between control
screens, adjust the selected option, or exit
the screen.
 
						

							ViewSonicVA1912w/VA1912wb 11
Main Menu Controls
Adjust the menu items shown below by using the up S and down T buttons.
Control Explanation
Auto Image Adjust sizes and centers the screen image automatically.
Contrast adjusts the difference between the image background (black level)
and the foreground (white level).
Brightness adjusts background black level of the screen image.
Audio Adjust
Vo l u m e increases the volume, decreases the volume, and mutes the audio.
Mute temporarily silences audio output.
Color Adjust provides several color adjustment modes, including preset color
temperatures and a User Color mode which allows independent adjustment of
red (R), green (G), and blue (B). The factory setting for this product is 6500K
(6500 Kelvin).
sRGB-This is quickly becoming the industry standard for color management,
with support being included in many of the latest applications. Enabling this
setting allows the LCD display to more accurately display colors the way they
were originally intended. Enabling the sRGB setting will cause the Contrast and
Brightness adjustments to be disabled.
9300K-Adds blue to the screen image for cooler white (used in most office
settings with fluorescent lighting).
6500K-Adds red to the screen image for warmer white and richer red.
5400K-Adds green to the screen image for a darker color.
5000K-Adds blue and green to the screen image for a darker color.
 
						

							ViewSonicVA1912w/VA1912wb 12
Control Explanation
User Color Individual adjustments for red (R), green (G), and blue (B).
1.To select color (R, G or B) press button [2].
2.To adjust selected color, pressSandT.
Important: If you select RECALL from the Main Menu when the product is 
set to a Preset Timing Mode, colors return to the 6500K factory preset.
Information displays the timing mode (video signal input) coming from the 
graphics card in the computer, the LCD model number, the serial number, and 
the ViewSonic
® website URL. See your graphics card’s user guide for 
instructions on changing the resolution and refresh rate (vertical frequency).
NOTE: VESA 1440 x 900 @ 60Hz (recommended) means that the resolution is 
1440 x 900 and the refresh rate is 60 Hertz.
Manual Image Adjust Sub-menu
H. Size (Horizontal Size) adjusts the width of the screen image.
H./V. Position (Horizontal/Vertical Position) moves the screen image left or 
right and up or down.
 
						

							ViewSonicVA1912w/VA1912wb 13
Control Explanation
Fine Tune sharpens the focus by aligning text and/or graphics with pixel
boundaries.
NOTE: Try Auto Image Adjust first.
Sharpness adjusts the clarity and focus of the screen image.
Setup Menu displays the menu shown below:
Language Select allows the user to choose the language used in the menus and
control screens.
Resolution Notice allows the user to enable or disable this notice.
If you enable the Resolution Notice shown above and your computer is set at a 
resolution other than 1440 x 900, the following screen appears.
 
						

							ViewSonicVA1912w/VA1912wb 14
Control Explanation
OSD Position allows the user to move the OSD menus and control screens.
OSD Timeout sets the length of time the OSD screen is displayed. For example,
with a “30 second” setting, if a control is not pushed within 30 seconds, the
display screen disappears.
OSD Background allows the user to turn the OSD background On or Off.
Memory Recall returns the adjustments back to factory settings if the display is
operating in a factory Preset Timing Mode listed in the Specifications of this
manual.
 
						

							ViewSonicVA1912w/VA1912wb 15
Other Information
Specifications
1 Macintosh computers older than G3 require a ViewSonic® Macintosh adapter. To order an adapter, contact
ViewSonic.LCDTy p e
Color Filter
Glass Surface19” (full 19 viewable diagonal area),
TFT (Thin Film Transistor), Active Matrix WXGA LCD,
0.285 mm pixel pitch
RGB vertical stripe
Anti-Glare
Input SignalVideo
SyncRGB analog (0.7/1.0 Vp-p, 75 ohms)
Separate Sync,
f
h:30-82 kHz, fv:50-85 Hz
CompatibilityPC
Macintosh
1
Up to 1440 x 900 Non-interlaced
Power Macintosh up to 1440 x 900
ResolutionRecommended
and supported1440 x 900 @ 60 Hz
1280 x 1024 @ 60, 70, 72 Hz
1024 x 768 @ 60, 70, 72, 75, 85 Hz
800 x 600 @ 56, 60, 72, 75, 85 Hz
640 x 480 @ 60, 75, 85 Hz
720 x 400 @ 70 Hz
PowerVoltage 100-240 VAC, 50-60 Hz (auto switch)
Display areaFull Scan 410.4 mm (H) x 256.5 mm (V)
16.2 (H) x 10.1 (V)
Operating
conditionsTemperature
Humidity
Altitude41° F to + 95° F (5° C to + 35° C)
20% to 80% (non-condensing)
To 10,000 feet
Storage
conditionsTemperature
Humidity
Altitude-4° F to + 131° F (-20° C to + 55° C)
20% to 85% (non-condensing)
To 40,000 feet
DimensionsPhysical 451 mm (W) x 391 mm (H) x 197 mm (D)
17.8 (W) x 15.4 (H) x 7.8 (D)
WeightPhysical 9.88 lb (4.48 kg)
RegulationsBSMI, CCC, PSB, C-Tick, CE, GS, MIC
Ergo, Gost-R/Hygienic, SASO, TCO03,
UL/cUL, FCC-B, ICES-B, NOM, TUV-S, E
NERGY STA R®
Power saving
modesOn
OffNormal              (green LED)

						

							ViewSonicVA1912w/VA1912wb 16
Troubleshooting
No power
• Make sure power button (or switch) is ON.
• Make sure A/C power cord is securely connected to the LCD display.
• Plug another electrical device (like a radio) into the power outlet to verify that the outlet is
supplying proper voltage.
Power is ON but no screen image
• Make sure the video cable supplied with the LCD display is tightly secured to the video
output port on the back of the computer. If the other end of the video cable is not attached
permanently to the LCD display, tightly secure it to the LCD display.
• Adjust brightness and contrast.
• If you are using an Macintosh older than G3, you need a Macintosh adapter.
Wrong or abnormal colors
• If any colors (red, green, or blue) are missing, check the video cable to make sure it is
securely connected. Loose or broken pins in the cable connector could cause an improper
connection.
• Connect the LCD display to another computer.
• If you have an older graphics card, contact ViewSonic
® for a non-DDC adapter.
Control buttons do not work
• Press only one button at a time.
 
						

							ViewSonicVA1912w/VA1912wb 17
Customer Support
For technical support or product service, see the table below or contact your reseller.
NOTE: You will need the product serial number.
Country/RegionWebsite T = Telephone
F = FAXEmail
United States www.viewsonic.comT= 800 688 6688
F= 909 468 [email protected]
Canada www.viewsonic.comT= 866 463 4775
F= 909 468 [email protected]
Latin America 
(Mexico/Chile)www.viewsonic.comT= 866 323 8056
F= 909 444 [email protected]
United Kingdom www.viewsoniceurope.com/ukwww.viewsoniceurope.com/
uk/Support/Calldesk.htm
Europe, Middle East, 
Baltic countries, and 
North Africawww.viewsoniceurope.com Contact your reseller
Australia/New Zealand www.viewsonic.com.auAUS= 1800 880 818
NZ= 0800 008 [email protected]
Singapore/Malaysia/
Thailandwww.ap.viewsonic.com T= 65 64616044 [email protected]
South Africa and
other countrieswww.ap.viewsonic.comT= 886 2 2246 3456
F= 886 2 2249 [email protected]
India www.in.viewsonic.com T= 1800 11 9999 [email protected] 
Hong Kong www.hk.viewsonic.com T= 852 3102 2900 [email protected]
Macau www.hk.viewsonic.com T= 853 700 303 [email protected]
Korea www.kr.viewsonic.com T= 080 333 2131 [email protected]