Vivitek D5000 User Manual

DLP Projector—User’s Manual 
– 44 – 
7. Press the  Menu button on the projector. 
8. Select  Installation II  → Advanced →Network . 
9. After getting into  Network, input the following: 
  DHCP: Off 
  IP Address: 10.10.10.10 
  Subnet Mask: 255.255.255.0 
  Gateway: 0.0.0.0 
  DNS Server: 0.0.0.0 
10. Press 
 (Enter) /  ► to confirm settings. 
Open a web browser  
(for example, Microsoft Internet Explorer  with Adobe Flash Player 9.0 or higher). 
 
11.  In the Address bar, input the IP address:...

DLP Projector – User’s Manual 
– 45  – 
Factory Reset 
Press the cursor  ▲▼ button to move up and down in the  Installation II
 menu. Select the  Factory 
Reset  sub menu and press 
 (Enter) /  ► to reset all the menu items to the factory default values 
(expect Language and Security Lock). 
 
 
Status 
Press the cursor  ▲▼ button to move up and down in the  Installation II
 menu. Select the   
Installation II  sub menu and press 
 (Enter) / ► to enter the  Status
 sub menu.
 
 
ITEM DESCRIPTION 
Active...

DLP Projector—User’s Manual 
– 46 – 
MAINTENANCE AND SECURITY 
Replacing the Projection Lamp 
The projection lamp should be replaced when it burns out. It should only be replaced with a certified 
replacement part, which you can order from your local dealer.  
Important: 
a.
 The projection lamp used in this product contains a small amount of mercury. 
b.  Do not dispose this product with general household waste. 
c. Disposal of this product must be carried out in accordance with the regulations of your...

DLP Projector – User’s Manual 
– 47  – 
 
6.  Use a screwdriver to remove 
the screws from the lamp 
module. 
 
7.  Pull out the lamp module. 
 
8.  Reverse steps 1 to 7 to install 
the new lamp module.  
While installing, align the 
lamp module with the 
connector and ensure it is 
level to avoid damage. 
Note:
  
The lamp module must sit 
securely in place and the 
lamp connector must be 
connected properly before 
tightening the screws.  
9.  Turn on the projector and reset the lamp after the lamp...

DLP Projector—User’s Manual 
– 48 – 
Resetting the Lamp 
After replacing the lamp, you should reset the lamp hour  counter to zero. Refer to the following: 
1.  Press the MENU button to open the 
OSD menu. 
2.  Press the cursor  ◄► button to move 
to the  Installation II  menu. Press the 
cursor  button to move down to  
Advanced . 
 
3.  Press the cursor  ▼▲ button to move 
down to  Lamp Hour Reset . 
 
4.  Press the cursor 
► or Enter button.  
A message screen appears. 
5.  Press  ▼▲◄►  buttons to...

DLP Projector – User’s Manual 
– 49  – 
Cleaning the Projector 
Cleaning the projector to remove dust and grime will help ensure trouble-free operation.  
Warning: 
1.  Be sure to turn off and unplug the projector at least 30 minutes before cleaning. Failure to do so 
could result in a severe burn. 
2.
 Use only a dampened cloth when cleaning. Do not allow water to enter the ventilation openings 
on the projector.  
3. If a little water gets into the projector interior while cleaning, leave unplugged in...

DLP Projector—User’s Manual 
– 50 – 
Using the Physical Lock 
Using the Kensington® Lock 
If you are concerned about security, attach the projector to a permanent object with the Kensington 
slot and a security cable.  
 
Note: 
Contact your vendor for details on purchasing a suitable Kensington security cable.   
The security lock corresponds to Kensington’s MicroSaver Security System. If you have any com-
ment, contact: Kensington, 2853 Campus Drive, San Mateo, CA 94403, U.S.A. Tel: 800-535-4242,...

DLP Projector – User’s Manual 
– 51  – 
 
TROUBLESHOOTING 
Common problems  and solutions 
These guidelines provide tips to deal with problems you may encounter while using the projector. If 
the problem remains unsolved, contact your dealer for assistance. 
Often after time spent troubleshooting, the problem  is traced to something as simple as a loose con-
nection. Check the following before proceeding to the problem-specific solutions. 
 Use some other electrical device to confirm that the...

DLP Projector—User’s Manual 
– 52 – 
LED Error Messages 
ERROR CODE MESSAGES POWER LED 
BLINK 
OVER TEMP  
LED 
LAMP LED  
BLINK 
Over temperature  OFF  ON  0 
Thermal break status error  4  0  0 
Lamp error  ON  0  On 
Fan1 error  6  0  1 
Fan2 error  6  0  2 
Fan3 error  6  0  3 
Lamp door open  7  0  0 
DMD error  8  0  0 
Color wheel error  9  0  0 
In the event of an error, please disconnect the AC power cord and wait for one (1) minute before re-
starting the projector. If the Power or Lamp LEDs...

DLP Projector – User’s Manual 
– 53  – 
Lamp Problems 
Problem: There is no light from the projector  
1.  Check that the power cable is securely connected. 
2.  Ensure the power source is good by testing with another electrical device. 
3.  Restart the projector in the correct order and check that the Power LED is green. 
4.  If you have replaced the lamp recently, try resetting the lamp connections.  
5.  Replace the lamp module. 
6.  Put the old lamp back in the projector and have the projector...