Vivitek D755wt User Manual

DLP Projector—User’s Manual 
 
 
Wired LAN Terminal functionalites 
Remote control and monitoring of a projector from a PC (or Laptop) via wired LAN is also possible. 
Compatibility with Crestron / AMX (Device Disco very) / Extron control boxes enables not only 
collective projector management  on a network but also management from a control panel on a PC 
(or Laptop) browser screen. 
* Crestron is a registered trademark of Crestr on Electronics, Inc. of the United States. 
* Extron is a registered...

DLP Projector—User’s Manual 
LAN RJ45 
1.  Connect an RJ45 cable to RJ45 ports on the projector and the PC (Laptop). 
 
2.  On the PC (Laptop), select  Start 
→ Control Panel  → Network  Connections . 
 
— 34—  

DLP Projector—User’s Manual 
3. Right-click on Local Area Connection, and select  Properties. 
 
4. In the  Properties  window, select the  General tab, and select  Internet Protocol (TCP/IP) . 
5. Click  Properties . 
 
— 35—  

DLP Projector—User’s Manual 
6. Click Use the following IP address  and fill in the IP address and Subnet mask, then click  OK. 
 
7. Press the  Menu button on the projector. 
8. Select Settings 2 →  Advanced 1 → RS232  → Network  Option 
9. After getting into  Network, input the following: 
 DHCP: Off 
  IP Address: 10. 10. 10. 10 
  Subnet Mask: 255.255.255.0 
  Gateway: 0.0.0.0 
  DNS Server: 0.0.0.0 
10. Press 
 (Enter) /  ► to confirm settings. 
11.  Open a web browser (for example, Microsoft...

DLP Projector—User’s Manual 
12.  In the Address bar, input the IP address: 10. 10. 10. 10. 
13. Press 
 (Enter) /  ►. 
The projector is setup for remote management. The LAN/RJ45 function  displays as follows. 
 
 
—  37—  

DLP Projector—User’s Manual 
— 38— 
CATEGORY ITEM INPUT-LENGTH 
IP Address  15 
IP ID 3 Crestron Control 
Port 5 
Projector Name 10 
Location 10 Projector 
Assigned To 10 
DHCP (Enabled) (N/A) 
IP Address  15 
Subnet Mask 15 
Default Gateway 15 
Network Configuration 
DNS Server 15 
Enabled (N/A) 
New Password 10 User Password 
Confirm 10 
Enabled (N/A) 
New Password 10 Admin Password 
Confirm 10 
For more information, please visit  http://www.crestron.com/.  

DLP Projector—User’s Manual 
RS232 by Telnet Function 
Besides projector connected to RS232 interface with “Hyper-Terminal” communication by 
dedicated RS232 command control, there is alte rnative RS232 command control way, so called 
“RS232 by TELNET” for  LAN/RJ45 interface. 
Quick Start-Guide for “RS232 by TELNET” 
Check and get the IP-Address on OSD of the projector. 
Make sure that laptop/PC can acce ss the web-page of the projector. 
Make sure that “Windows Firewall” setting to be dis abled in case...

DLP Projector—User’s Manual 
Input the command format like the below: 
telnet  ttt.xxx.yyy.zzz  23 (“Enter” key pressed) 
( ttt.xxx.yyy.zzz : IP-Address of the projector) 
If Telnet-Connection ready, and us er can have RS232 command inpu t, then “Enter” key pressed, 
the RS232 command will be workable. 
 
How to have TELNET enable d in Windows VISTA / 7 
By default installation for Windows VISTA, “TELNE T” function is not included. But end-user can 
have it by way of “Turn Windows features On or Off” to...

DLP Projector—User’s Manual 
Select “Turn Windows features on or off” to open 
 
Have “Telnet Client” option checked, then press “OK” button. 
 
Specsheet for “RS232 by TELNET” : 
1. Telnet: TCP 
2. Telnet port: 23 (for more detail, kindly please get contact with the  service agent or team) 
3. Telnet utility: Windows “T ELNET.exe” (console mode) 
4.  Disconnection for RS232-by-Telnet control normally: Close Wi ndows Telnet utility directly 
after TELNET connection ready 
5.  Limitation 1 for...

DLP Projector—User’s Manual 
Advanced 2 Feature 
Press the Menu button to open the OSD menu. Press  ◄► to move to the  Settings 2 menu. 
Press  ▲▼ to move to the  Advanced 2 menu and then press  Enter or ►. Press  ▲▼ to move up 
and down in the Advanced 2  menu. Press ◄► to
 enter and change values for setting. 
 
ITEM DESCRIPTION 
Sleep Timer (min)  Press the cursor 
◄► buttons to enter and set Sleep timer. The projector automatically 
turns off after the preset period of time. 
Source Filter  Press...