Vivitek D795wt User Manual

							
DLP Projector – User’s Manual 
 
 
 Rear view 
12 34
56
7
89
12 11
1
0 
ITEM LABEL DESCRIPTION SEE PAGE: 
Connect the RGB CABLE to a display 
(Loop Thru only for VGA IN-1) 1.  VGA OUT 
2.  RS-232 Connect RS-232 serial port cable for remote control 
Connect the RGB CABLE from a computer and  
components 3.  VGA – 1 
Connect the RGB CABLE from a computer and  
components 4.  VGA – 2 9
5.  RJ – 45 Connect a LAN CABLE from Ethernet 
6.  S-VIDEO IN Connect the S-VIDEO CABLE from a video device 
7.  VIDEO IN Connect the COMPOSITE CABLE from a video device  
8.  USB Connect the USB CABLE from a computer  
119.  AC IN Connect the POWER CABLE 
10.  HDMIConnect the HDMI
–  3 –  
TMTM CABLE from a HDMITM device 
11.  AUDIO IN Connect an audio cable from the input device 9
12.  AUDIO OUT Connect an audio cable from the output device 
Note: 
If your video equipment has various input sources,  it is recommended to connect in priority of 
HDMITM/DVI, component (thru VGA), S-Video, Composite for better picture quality. 
Downloaded From projector-manual.com Vivitek Manuals 
						

							
DLP Projector – User’s Manual 
 
 
Bottom view 
70.00110.00
126.00228.00
20.00
56.00
146.00
236.00100.0240.0
12 3
3 3 2
 
ITEM LABEL DESCRIPTION SEE PAGE: 
441.  Security bar Helps protect the projector from unauthorized use 
2.  Tilt adjustors Rotate adjusters lever to adjust angle position 
3.  Ceiling support holes Contact your dealer for information on mounting the projector on a ceiling 
 
Note: 
When installing, ensure that you us
e only UL Listed ceiling mounts. 
For ceiling installations, use approved mounting har dware and M4 screws with a maximum screw 
depth of 12 mm (0.47 inch).  
The construction of the ceiling mount must be of a suitable shape and strength. The ceiling mount 
load capacity must exceed the  weight of the installed equipment, and as an additional precaution 
be capable of withstanding three times the weight  of the equipment (not less than 5.15 kg) over a 
period of 60 seconds. 
– 4 – 
Downloaded From projector-manual.com Vivitek Manuals 
						

							
DLP Projector – User’s Manual 
 
 
Remote Control Parts 
 
 
Important: 
1.  Avoid using the projector with bright fluoresc ent lighting turned on. Certain high-frequency fluo-
rescent lights can disrupt remote control operation. 
 
2. Be sure nothing obstructs the path between the re mote control and the projector. If the path be-
tween the remote control and the projector is obstructed, you can bounce the signal off certain 
reflective surfaces such as projector screens. 
 
3. The buttons and keys on the projector have the  same functions as the corresponding buttons on 
the remote control. This user’s manual descri bes the functions based on the remote control. 
– 5 –  
Downloaded From projector-manual.com Vivitek Manuals 
						

							
DLP Projector – User’s Manual 
 
 
– 6 –  
 
ITEM LABEL DESCRIPTION SEE PAGE: 
1.  IR transmitter  Transmit s signals to projector 
2.  Status LED  Lights when the remote control is used 
3.  Laser  Press to operate the on-screen pointer 
4.  Up  Up arrow when connect ed through USB to a PC 
5.  Right  Right arrow when connected through USB to a PC 
6.  Down  Down arrow when conn ected through USB to a PC 
7.  Page Down  Page down when connected through USB to a PC 
8.  Up cursor  
9.  Right cursor  
10.  Down cursor Navigates and changes settings in the OSD
  
18 
11.  Volume +/-  Adjusts volume 17 
12.  Mute  Mutes the built-in speaker 
13.  Zoom+  Zoom in  
14.  Zoom- Zoom out 
15.  Freeze   Freeze/unfreezes the on-screen picture 
16.  Blank  Makes the screen blank 
17.  Source  Detects the input device 
18.  Auto  Auto adjustment for phase, tracking, size, position 
19.  Menu  Opens the OSD  18 
20.  Status  Opens the OSD Status menu (the menu only opens when an 
input device is detected) 30 
21.  Keystone top/bottom  Corrects image-tr
apezoid (wider top/bottom) effect 16 
22.  Left cursor  Navigates and changes settings in the OSD   
23.  Enter Changes settings in the OSD 
24.  Page Up  Page up when connected through USB to a PC 
25.  Left  Left arrow when connected through USB to a PC 
26.  Enter  Enter key when connected through USB to a PC 
18 
27.  Power   Turns the projector on or off 11 
28.  Laser  Use as on-screen pointer.  DO NOT POINT IN EYES. 
Downloaded From projector-manual.com Vivitek Manuals 
						

							
DLP Projector – User’s Manual 
 
 
–  7 –  
Remote Control Operating Range 
The remote control uses infrared transmission to cont rol the projector. It is not necessary to point the 
remote directly at the projector. Provided you are not holding the remote perpendicular to the sides or 
the rear of the projector, the re mote will function well within a radi us of about 7 meters (23 feet) and 
15 degrees above or below the projector level. If the pr ojector does not respond to the remote control, 
move a little closer.   
Projector and Remote Control Buttons 
The projector can be operated using t he remote control or the buttons on the top of the projector. All 
operations can be carried out with the remote cont rol; however, the buttons on the projector are lim-
ited in use.  
 
Downloaded From projector-manual.com Vivitek Manuals 
						

							
DLP Projector – User’s Manual 
 
 
 
SETUP AND OPERATION 
Inserting the Remote  Control Batteries  
– 8 – 
1.  Remove the battery compartment cover 
by sliding the cover in the direction of 
the arrow. 
 
2.  Insert the battery with the positive side 
facing up. 
 
3.  Replace the cover. 
 
 
Caution: 
1. Only use AAA batteries (Alkaline batteries are recommended). 
 
2. Dispose of used batteries accordi ng to local ordinance regulations.  
 
3. Remove the batteries when not usi ng the projector for prolonged periods. 
 
Downloaded From projector-manual.com Vivitek Manuals 
						

							
DLP Projector – User’s Manual 
 
 
–  9  – 
Connecting Input Devices 
A PC or notebook computer and video devices can be connected to the projector at the same time. Video 
devices include DVD, VCD, and VHS players, as we ll as movie camcorders and digital still cameras. 
Check the user manual of the connecting device to  confirm it has the appropriate output connector.  
ABCDEFG
HIJKL 
ITEM LABEL DESCRIPTION 
A VGA OUT Connect the RGB CABLE to a display 
(Loop Thru only for VGA IN-1) 
B RS-232  Connect RS-232 serial port cable for remote control 
C VGA – 1 Connect the RGB CABLE 
from a computer and  
components 
D VGA – 2  Connect the RGB CABLE 
from a computer and  
components 
E RJ – 45  Connect a LAN CABLE from Ethernet 
F HDMITM  Connect the HDMITM CABLE from a HDMITM device 
G S-VIDEO IN  Connect the S-VIDEO CABLE from a video device 
H VIDEO IN  Connect the COMPOSITE CABLE from a video device  
I USB  Connect the USB CABLE from a computer  
J AC IN  Connect the POWER CABLE 
Downloaded From projector-manual.com Vivitek Manuals 
						

							
DLP Projector – User’s Manual 
 
 
– 10 –  
ITEM LABEL DESCRIPTION 
K AUDIO IN  Connect an audio cable from the input device 
L AUDIO OUT  Connect an audio cable from the output device 
！Warning: 
As a safety precaution, disconnect all power to  the projector and connecting devices before making 
connections. 
Downloaded From projector-manual.com Vivitek Manuals 
						

							
DLP Projector – User’s Manual 
 
 
–  11  – 
Starting and Shutting  down the Projector 
1.  Connect the power cord to the projector. 
Connect the other end to a wall outlet. 
The  POWER  LED on the projector 
light. 
2.   Turn on the connected devices.  
3.  Ensure the  POWER LED displays a 
solid orange. Then press the  POWER 
button 
of the remote to turn on the pro-
jector.  
 
The projector splash screen displays and 
connected devices are detected. 
 
See  Setting an Access Password 
(Security Lock)  on page 13 if security 
lock is enabled. 
4.   If more than one input device is con-
nected, press the  SOURCE button 
of 
the remote 
and use  ▲▼ to scroll 
among devices. 
(Component is supported through the 
RGB to COMPONENT ADAPTER.) 
 
 
•   VGA 1/VGA 2: Analog RGB 
Component: DVD input YCbCr / YPbPr, or 
HDTV input YPbPr via HD15 connector 
•   Composite Video: Traditional composite video 
• S-Video: Super video (Y/C separated) 
•  
HDMITM: HDMITM, DVI 
Downloaded From projector-manual.com Vivitek Manuals 
						

							
DLP Projector – User’s Manual 
 
 
– 12 –  
5.  When the “Power Off? /Press Power 
again” message appears, press the 
POWER  button. The projector turns 
off. 
 
Caution: 
Do not unplug the power cord until the POWE R LED change to orange–indicating the projector 
has cooled down. 
 
 
 
Downloaded From projector-manual.com Vivitek Manuals