Vivitek D860 User Manual

							DLP Projector—User’s Manual 
Installation II Menu  
Press the MENU button to open the  OSD menu. Press the cursor  ◄► button to move to the  Installa-
tion II  menu. Press the cursor  ▲▼ button to move up and down in the Installation II menu.  
 
ITEM DESCRIPTION 
Auto Source  Press the cursor ◄► button to enable or disable  automatic source detection.  
Auto Power Off 
(min.) Press the cursor ◄►
 button to enable or disable automatic shutdown of lamp when no signal. 
Auto Power On  Press the cursor ◄► button to enable or disable automatic power On when AC power is supplied. 
Fan Speed  Press the cursor ◄►
 button to toggle between Normal and High fan speeds.  
Note : We recommend selecting high speed in high temperatures, high humidity, or high  
altitude areas. 
Lamp Mode  Press the cursor ◄►
 button to select the lamp mode for higher brightness or lower brightness 
to save lamp life. 
Advanced Press  (Enter) /  ► to enter the Advanced menu. See  Advanced Feature on page 35. 
Factory Reset  Press  (Enter) / ►
 to reset all items to factory preset values. 
Status Press  (Enter) / 
►
 to enter the Status menu. See page 
38 for more information on Status. 
 
– 34 –   
						

							DLP Projector – User’s Manual 
Advanced Feature 
Press the Menu button to open the OSD menu. Press  ◄► to move to the  Installation II menu. 
Press  ▲▼ to move to the  Advanced menu and then press  Enter or ►. Press  ▲▼ to move up and 
down in the  Advanced menu. Press  ◄► to change values for setting. 
 
ITEM DESCRIPTION 
OSD Menu Setting  Press Enter / 
► to enter the OSD setting menu. See page  36 for more information on  OSD 
Menu
 Setting . 
Peripheral Test  Press Enter/ 
► to enter the Peripheral Test menu. See page  36 for more information on 
Peripheral Test . 
Lamp Hour Reset  After replacing the lamp, this item should be reset. See page 
37 for more information on Lamp 
Ho
ur Reset . 
Low Power Mode  Press ◄► to turn Low Power Mode on or off. 
3D Press Enter/ ► to enter the 3D menu. See page  37 for more information on  3D setting.. 
Note: 
To enjoy the 3D function, fi rst enable the Play Movie in 3D setting found in your DVD  
device under the 3D Disc Menu. 
 
– 35  –  
						

							DLP Projector—User’s Manual 
OSD Menu Setting  
 
ITEM DESCRIPTION 
Menu Position Press ◄► button to select different OSD location. 
Translucent Menu  Press ◄► button to select OSD background translucent level.  
Menu Display  Press ◄► button to select OSD timeout delay. 
Peripheral Test 
 
ITEM DESCRIPTION 
Remote Control Test  Press  (Enter) / ► to test the IR remote controller for diagnostic.  
Color Test  Press  (Enter) / ► to select different colors on screen. 
Button Test  Press  (Enter) / ► to test the button on keypad. 
USB Test (*)  Press  (Enter) / ► to test the USB connection with connected PC. 
Note: (*) Not available in D860/D861 Series. 
– 36 –   
						

							DLP Projector – User’s Manual 
Lamp Hour Reset 
 
Please refer to Resetting the Lamp  on page 41 to reset the lamp hour counter. 
 
3D 
 
ITEM DESCRIPTION 
3D Press  ◄► to select Off, DLP-Link or IR. 
3D Sync Invert  Press ◄► to turn 3D Sync Invert On or Off. 
– 37  –  
						

							DLP Projector—User’s Manual 
 
Factory Reset 
Press the cursor ▲▼ button to move up and down in the  Installation II menu. Select the  Factory 
Reset  sub menu and press 
 (Enter) /  ► to reset all the menu items to the factory default values 
(expect Language and Security Lock). 
 
Status 
Press the cursor ▲▼  button to move up and down in the  Installation II menu. Select the   
Installation II sub menu and press 
 (Enter) /  ► to enter the  Status sub menu.
 
 
ITEM DESCRIPTION 
Active Source  Display the activated source. 
Video Information  Displays resolution/video information for RGB source and color standard for Video source. 
Lamp Hours  Lamp hour used information is displayed. Eco and Normal counters are separated. 
 
 
– 38 –  
						

							DLP Projector – User’s Manual 
– 39  – 
MAINTENANCE AND SECURITY 
Replacing the Projection Lamp 
The projection lamp should be replaced when it burns out. It should only be r eplaced with a certified 
replacement part, which you can order from your local dealer.  
Important: 
a.  The projection lamp used in this product contains a small amount of mercury. 
b.  Do not dispose this product  with general household waste. 
c. Disposal of this product must be carried out in a ccordance with the regulations of your local  
authority. 
Warning: 
Be sure to turn off and unplug the projector at least 30 minutes before replacing the lamp. Failure to 
do so could result in a severe burn. 
 
Caution: 
In rare cases the lamp bulb may burn out during  normal operation and cause glass dust or shards 
to be discharged outward from the rear exhaust vent. 
Do not inhale or do not touch glass dust or shards. Doing so could result in injury.  
Always keep your face away from the exhaust vent  so that you do not suffer from the gas and bro-
ken shards of the lamp. 
When removing the lamp from a ceiling-mounted proj ector, make sure that no one is under the pro-
jector. Glass fragments could fall if the lamp has been burned out.  
！ IF A LAMP EXPLODES 
If a lamp explodes, the gas and broken shards may scatter inside the projector and they may come 
out of the exhaust vent. The gas contains toxic mercury. 
Open windows and doors for ventilation. 
If you inhale the gas or the shards  of the broken lamp enter your eyes or mouth, consult the doctor 
immediately.  
1.  Loosen the single screw on 
the lamp compartment cover. 
  
						

							
DLP Projector—User’s Manual 
– 40 – 
2.  Remove the lamp compart-
ment cover. 
 
3.  Remove the three screws 
from the lamp module.  
 
4.   Lift the module handle up. 
5.   Pull firmly on the module  
handle to remove the lamp 
module. 
 
6.   Reverse steps 1 to 5 to install 
the new lamp module.  
While installing, align the 
lamp module with the  
connector and ensure it is 
level to avoid damage. 
Note:  The lamp module must 
sit securely in place and the 
lamp connector must be con-
nected properly before 
tightening the screws. 
  
						

							DLP Projector – User’s Manual 
Resetting the Lamp 
After replacing the lamp, you should reset the lamp hour counter to zero. Refer to the following: 
1.  Press the MENU button to open the 
OSD menu. 
2.  Press the cursor  ◄► button to move 
to the  Installation II menu. Press the 
cursor  button to move down to  
Advanced . 
3.  Press the cursor  ▼▲ button to move 
down to  Lamp Hour Reset . 
4.  Press the cursor ► or Enter button.  
A message screen appears. 
5.  Press  ▼▲◄►  buttons to reset the 
lamp hour. 
6.  Press the  MENU button to get back 
to Installation II. 
 
–  41  –  
						

							DLP Projector—User’s Manual 
– 42 – 
Cleaning the Projector 
Cleaning the projector to remove dust and grime will help ensure trouble-free operation.  
Warning: 
1. Be sure to turn off and unplug the projector at  least 30 minutes before cleaning. Failure to do so 
could result in a severe burn. 
2. Use only a dampened cloth when cleaning. Do not allow water to enter the ventilation openings 
on the projector.  
3. If a little water gets into the projector interior  while cleaning, leave unplugged in a well-ventilated 
room for several hours before using. 
4. If a lot of water gets into the projector inte rior when cleaning, have the projector serviced. 
Cleaning the Lens 
You can purchase optic lens cleaner from most camera stores . Refer to the following to clean the pro-
jector lens. 
1.   Apply a little optic lens cleaner to a clean soft cloth. (Do not apply the cleaner directly to the lens.) 
2.   Lightly wipe the lens in a circular motion. 
Caution: 
1. Do not use abrasive cleaners or solvents. 
2. To prevent discoloration  or fading, avoid getting cleaner on the projector case. 
Cleaning the Case 
Refer to the following to clean the projector case. 
1.  Wipe off dust with a clean dampened cloth. 
2.   Moisten the cloth with warm water and mild deterg ent (such as used to wash dishes), and then wipe 
the case. 
3.   Rinse all detergent from the cloth and wipe the projector again. 
Caution: 
To prevent discoloration or fading of the case, do not use abrasive  alcohol-based cleaners.  
						

							DLP Projector – User’s Manual 
Using the Kensington® Lock 
Using the Kensington® Lock 
If you are concerned about security, attach the projector to a permanent object with the Kensington 
slot and a security cable.  
 
For D860/D861 Series 
 
 
 
For D862 Series 
 
 
 
Note: 
Contact your vendor for details on purchasing a suitable Kensi ngton security cable.  
The security lock corresponds to Kensington’s Micr oSaver Security System. If you have any com-
ment, contact: Kensington, 2853 Campus Drive, San Mateo, CA 94403, U.S.A. Tel: 800-535-4242, 
http://www.Kensington.com. 
 
– 43  –