Vizio E191VA HDTV User Manual

							1
9
Installing the Base
1
Align the 8 tabs on the base with the 8 slots on the bottom of the TV.
Slots on TV
2
Press down on one side of the base and gently slide forward until you  feel it click into place.
press here  
while sliding forward.
3
Press down on the other side  of the base and gently slide forward 
until you feel it click into place.
Base installation is complete.
press here   
while sliding forward.
Removing the Base
1
If you plan to wall mount the TV, you will need to remove the base.
To remove the base, gently lift the wide tab.
Gently lift 
this tab
2
While gently lifting the tab, gently slide one side of the base away fro\
m  TV.
3
Gently slide the other side  of the base away from the TV.                
						

							1
10
Installing the TV on a Wall
To mount your TV on a wall, you will need a wall mount. Consult 
the information below to find the appropriate mount for your TV 
model:Installing a TV on a wall requires lifting. To prevent 
injury or damage to the TV, ask someone to help you.
E191VA
Screw Size: M4
Screw Length: 10mm
Screw Pitch: 0.7mm
Hole Pattern: 75mm (V) x 
 
75mm (H)
Be sure the mount you choose is capable of supporting the 
weight of the TV. After you have determined that you have the 
correct mount for your TV, you can begin the installation.
To install your TV on a wall:
1 .  Disconnect any cables connected to your TV.
2 .  Place the TV face-down on a clean, flat, stable surface. 
Be sure the surface is clear of debris that can scratch or 
damage  the TV.
3 .  Remove the base by loosening and removing the screws.
4 .  Attach your TV and wall mount to the wall, carefully following 
the instructions that came with your mount.  
 
Use only with a UL-listed wall mount bracket rated for the 
weight/load of this TV. See 
Appendix B - Specifications for the 
weight of this TV.  
						

							2
11
Controls and Connections
ReaR Panel
Rear Panel
HDMI - Connect HDMI device.
PC Audio In - Connect 3.5mm PC audio cable.
RGB - Connect RGB cable to PC.
Component/Composite - Connect component or 
composite device.
 A U D IO A
U DIO
O U T
     
( A RC)
     1 CABLE/ANTENNA
RGB PC
USB
Y /V
Pb /CbPr/Cr L
R
C O M PO SIT E ( GO OD )
H DM I( B ES T) RGB (PC) DTV/TV
AU DIO O UT
U SB
COMPONENT (BETTER)
Coaxial - Connect coaxial cable from cable, 
satellite, or antenna.
3.5mm Audio - 
Connect headphones powered 
speakers, or other 3.5mm audio device.
USB 2.0 - Connect USB thumb drive to play photo 
slideshow or to update firmware.
note:  The image shown here is 
for illustrative purposes only and 
may be subject to change. The 
actual number of ports and their 
locations may vary, depending on 
the model.  
						

							2
12
Side Panel
Side Panel
POWER - Turn TV off or on.
MENU - Open the on-screen menu.
CHANNEL UP/DOWN - Change the channel.
VOLUME UP/DOWN - Increase or decrease volume level. INPUT - Change input source.  
						

							2
13
FR ont Panel
Front Panel
REMOTE SENSOR  
 
When using the remote, aim it directly at this sensor.           
						

							2
14
Remote ContRol
Remote Control
inPut 
Change the currently-displayed input.
aRRow  
Navigate the on-screen menu.
exit 
Close the on-screen menu. CloSed CaPtionS
 
Open the closed caption menu.
a/V ContR
olS 
Control USB photo viewer.
wide 
Switch the display mode.
mute 
Turn the audio off or on.
BaCk 
Go to the previous on-screen menu. PoweR
 
Turn TV on or off.
menu
 
Display the on-screen menu.
inF
o  
Display the info window.
daSh
 
Use with number pad to manually enter 
a digital sub-channel. (For example, 
18-4 or 18-5.) Channel uP/down
 
Change the channel. Guide
 
Display the info window.
laSt 
Return to the channel last viewed.
numBeR  Pad 
Manually enter a channel.
Volume uP/down 
Increase or decrease loudness of the audio. ok
 
Select the highlighted menu option.
V Button 
Open the USB photo viewer.              
						

							2
15
Replacing the Batteries
1 . Remove the battery cover.
2 .  Insert two batteries into the remote control. Make sure that 
the (+) and (-) symbols on the batteries match the (+) and 
(-) symbols inside the battery compartment.
3 .  Replace the battery cover.
• Use only good quality batteries.
•  Inserting the batteries incorrectly may result in 
cracking or leakage that may cause a fire or 
result in injury.
•  Dispose of old or dead batteries in accordance 
with local hazardous waste regulations.
•  Keep batteries away from children and pets.
Replacing Batteries  
						

							3
16
Connecting Your Devices
ConneCting A DeviCe
 AU D IO A
U DIO
O U T
     
( A RC)
     1 CABLE/ANTENNA
RGB PC
USB
Y /V
Pb /CbPr/Cr L
R
C O M PO SIT E ( GO OD )
H DM I( B ES T) RGB (PC) DTV/TV
AU DIO O UT
U SB
COMPONENT (BETTER)
Connecting a Device
BeSt
HDMi CABLe • DigitAL 
• HD viDeo (1080p)* 
• HD AUDio
gooD
Av CABLe
• AnALog 
• viDeo (480i)* 
• SteReo AUDio
BetteR
CoMPonent CABLe
• AnALog 
• HD viDeo (1080p)* 
• SteReo AUDio
* Maximum Resolution
Game Console
Cable/Satellite Box
DVD/Blu-ray Player
Your TV can be used to display output from most devices. 
1 . 
Verify that your device has a video port that matches an 
available port on the TV (HDMI, Component, etc).
2 .  Turn the TV and your device off.
3 .  Connect the appropriate cable (not included) to the TV and 
the device.
4 .  Turn the TV and your device on. Set the TV’s input to match 
the connection you used (HDMI, Component, etc).
note:  The image shown here is for illustrative purposes only and may be 
subject to change. The actual number of ports and their locations may 
vary, depending on the model.     
						

							3
17
 AU D IO A
U DIO
O U T
     
( A RC)
     1 CABLE/ANTENNA
RGB PC
USB
Y /V
Pb /CbPr/Cr L
R
C O M PO SIT E ( GO OD )
H DM I( B ES T) RGB (PC) DTV/TV
AU DIO O UT
U SB
COMPONENT (BETTER)
ConneCting An AUDio DeviCe
Home Audio Receiver
VIZIO Sound Bar
Connecting an Audio Device
Your TV can output sound to an audio device, such as a receiver 
or sound bar. 
1 . 
Verify that your device has a audio port that matches an 
available port on the TV (Optical, etc).
2 .  Turn the TV and your audio device off.
3 .  Connect the appropriate cable (not included) to the TV and 
the device.
4 .  Turn the TV and your device on.
3.5mm Cable
note: The image shown here is for illustrative purposes only 
and may be subject to change. The actual number of ports 
and their locations may vary, depending on the model.   
						

							3
18
 AU D IO A
U DIO
O U T
     
( A RC)
     1 CABLE/ANTENNA
RGB PC
USB
Y /V
Pb /CbPr/Cr L
R
C O M PO SIT E ( GO OD )
H DM I( B ES T) RGB (PC) DTV/TV
AU DIO O UT
U SB
COMPONENT (BETTER)
Connecting a PC
ConneCting A PC
RGB Cable (For Video)
3.5mm Cable (For Audio)
Your TV can be used to display output from a personal computer.
To use your TV as a PC display:
1 . 
Connect an RGB cable (not included) to your PC and the 
RGB port on the back of the TV. This cable transmits video. 
2 .  Connect a 3.5mm cable (not included) to your PC and the 
PC Audio In port on the back of the TV. This cable transmits 
audio. 
3 .  Set your PC’s resolution to match the resolution of your TV. 
See 
Appendix B - Specifications.Personal Computer
note:  The image shown here is for illustrative purposes only and may be 
subject to change. The actual number of ports and their locations may 
vary, depending on the model.