Vizio E370-A0 HDTV User Manual

							1
5
Installing the TV on a Wall
To mount your TV on a wall, you will need a wall mount. Consult 
the information below to find the appropriate mount for your TV 
model:Installing a TV on a wall requires lifting. To prevent 
injury or damage to the TV, ask someone to help you.
E370-A0
Screw Size: M4
Screw Length: 20mm
Screw Pitch: 0.7mm
Hole Pattern: 100mm (V) x 100mm (H)
Be sure the mount you choose is capable of supporting the 
weight of the TV. After you have determined that you have the 
correct mount for your TV, you can begin the installation.
To install your TV on a wall:
1 .  Disconnect any cables connected to your TV.
2 .  Place the TV face-down on a clean, flat, stable surface. 
Be sure the surface is clear of debris that can scratch or 
damage  the TV.
3 .  Remove the base by loosening and removing the screws.
4 .  Attach your TV and wall mount to the wall, carefully following 
the instructions that came with your mount.  
 
Use only with a UL-listed wall mount bracket rated for the 
weight/load of this TV. See 
Appendix A - Specifications for 
the weight of this TV.  
						

							2
6
Controls and Connections
ReaR Panel
Rear Panel
Coaxial - Connect coaxial cable from cable, 
satellite, or antenna. Optical Audio Out - Connect optical/SPDIF audio 
device, such as home audio receiver. Stereo Audio Out - Connect  RCA audio cable to 
audio device. HDMI - Connect HDMI device.
Component/Composite - Connect component 
and composite devices.
USB - Connect USB thumb drive to view photo 
slideshow.
HDMI - Connect HDMI device.  
						

							2
7
FR ont Panel
Front Panel
REMOTE SENSOR   
When using the remote, aim it directly at this sensor.  
						

							2
8
Remote ContRol
Remote Control
InPut 
Change the currently-displayed input.
aRRow  
Navigate the on-screen menu.
exIt 
Close the on-screen menu. Closed CaPtIons
 
Open the closed caption menu.
a/V ContR
ols 
Control USB photo viewer.
wIde 
Switch the display mode.
mute 
Turn the audio off or on.
BaCk 
Go to the previous on-screen menu. PoweR
 
Turn TV on or off.
menu
 
Display the on-screen menu.
InF
o  
Display the info window.
dash
 
Use with number pad to manually enter 
a digital sub-channel. (For example, 
18-4 or 18-5.) Channel uP/down
 
Change the channel. GuIde
 
Display the info window.
last 
Return to the channel last viewed.
numBeR  Pad 
Manually enter a channel.
Volume uP/down 
Increase or decrease loudness of the audio. ok
 
Select the highlighted menu option.
V Button 
Open the USB photo viewer.              
						

							2
9
Replacing the Batteries
Replacing Batteries
1 .  Remove the battery cover.
2 .  Insert two batteries into the remote control. Make sure that 
the (+) and (-) symbols on the batteries match the (+) and 
(-) symbols inside the battery compartment.
3 .  Replace the battery cover.
• Use only good quality batteries.
•  Inserting the batteries incorrectly may result in 
cracking or leakage that may cause a fire or 
result in injury.
•  Dispose of old or dead batteries in accordance 
with local hazardous waste regulations.
•  Keep batteries away from children and pets.  
						

							3
10
Connecting Your Devices
ConneCting A DeviCe
CONNECTING A DEVICE
BeSt
HDMi CABLe• DigitAL 
• HD viDeo (1080p)* 
• HD AUDio
gooD
Av CABLe
• AnALog 
• viDeo (480i)* 
• SteReo AUDio
BetteR
CoMPonent CABLe
• AnALog 
• HD viDeo (1080i)* 
• SteReo AUDio
* Maximum Resolution
Game Console
Cable/Satellite Box
DVD/Blu-ray Player
Your TV can be used to display output from most devices. 
1 . 
Verify that your device has a video port that matches an 
available port on the TV (HDMI, Component, etc).
2 .  Turn the TV and your device off.
3 .  Connect the appropriate cable (not included) to the TV and 
the device.
4 .  Turn the TV and your device on. Set the TV’s input to match 
the connection you used (HDMI-1, HDM1-2, etc).    
						

							3
11
ConneCting An AUDio DeviCe
Home Audio Receiver
VIZIO Sound Bar
CONNECTING AUDIO DEVICE
Your TV can output sound to an audio device, such as a receiver 
or sound bar. 
1 . 
Verify that your device has a audio port that matches an 
available port on the TV (Optical, etc).
2 .  Turn the TV and your audio device off.
3 .  Connect the appropriate cable (not included) to the TV and 
the device.
4 .  Turn the TV and your device on.
RCA Cable
Optical/SPDIF Cable
gooD
BetteR    
						

							4
12
Completing the First-Time Setup
The first time you turn on the TV, the Setup App will guide you 
through each of the steps necessary to get your TV ready for use.
Before you begin the first-time setup:• Your TV should be installed and the power cord should 
be connected to an electrical outlet.
•  Your devices should be connected.
To complete the first-time setup:
1 .  Press the Power/Standby  
button on the remote. The TV 
powers on and the Setup App 
starts.  
 
 
2 .  Use the Up/Down Arrow  
buttons on the remote to 
highlight your preferred 
language and press OK.  
 
 
3 .  Use the OK and Arrow Up/
Down buttons on the remote 
to highlight Home Mode and 
press  OK. 
 4 .  Use the OK and Arrow Up/
Down buttons on the remote to 
highlight your time zone and 
press  OK. 
 
 
5 .  Use the OK and Arrow Up/
Down Buttons on the remote to 
turn daylight saving time On or 
Off. 
 
 
6 .  Answer the on-screen questions 
about your TV connection 
using the Arrow and OK  
buttons on the remote.  
 
 
7 .  Use the Arrow buttons to 
highlight Start the Channel 
Scan and press OK.  
 
 
 
8 .  When you have finished the 
channel scan, highlight Exit to 
Live TV and press OK.  
The First-Time Setup is complete.  
						

							5
13
Using the On-Screen Menu
Your TV features an easy-to-use on-screen menu. 
To open the on-screen menu, press the MENU button on the 
remote. 
From this menu, you can:• Change the input source
•  Change the screen aspect   
ratio
•  Set up closed captioning
•  Activate the sleep timer 
•  Adjust the picture settings
•  Adjust the audio settings
•  Change TV  settings
•  Access USB photo slideshow
•  Access the help menu
 
 
 NavigatiNg the ON-ScreeN MeNU
To open the on-screen menu, press  the  MENU button on the remote. 
Use the Arrow buttons to highlight 
a menu option, and press the OK  
button to select that option.  
 
While navigating the on-screen menu, you can press 
the BAC K  button at any time to return to the previous 
menu  screen. The  EXIT button will close the on-screen 
menu.
INPUTINPUT
INFOCC
MENU
GUIDE
1
4
7 2
5
8
0
WIDE
3
CH
CHVOL
VOL
69
BACK
EXIT
OK
INFOCC
MENU
GUIDE
1
4
7 2
5
8
0
WIDE
3
CH
CHVOL
VOL
69
BACK
EXIT
OK  
						

							5
14
chaNgiNg the iNpUt SOUrce
External devices such as DVD players, Blu-Ray Players, and video 
game consoles can be connected to your TV. To use one of these 
devices with your TV, you must first change the input source in the 
on-screen menu.
To change the input device: 1 .  Press the MENU button on the 
remote. The on-screen menu is 
displayed.
2 .  Use the Arrow buttons on the 
remote to highlight the Settings  
icon and press OK. The TV 
Settings menu is displayed.
3 .  Use the Up/Down Arrow  
buttons on the remote to 
highlight the input source and 
press  OK. The Input Source 
Selection menu is displayed.
4 .  Use the Up/Down Arrow  
buttons on the remote to 
highlight the input source you 
wish to display. Press OK, then 
press  EXIT. 
 
 
 
chaNgiNg the ScreeN aSpect ratiO
The TV can display images in four different modes: Wide, Zoom, 
Normal, and Stretch. Each mode displays the picture differently.
To change the screen aspect ratio:
1 .  Press the MENU button on the 
remote.
2 .  Use the Arrow buttons to 
highlight the Wide icon. Press 
OK.
3 .  Use the Arrow buttons to highlight your desired screen mode 
and press OK:
• Normal  preserves the content’s original aspect ratio. 
Since the 4:3 aspect ratio is not large enough to fill the 
TV’s screen, black bars are added to the left and right of 
the display image.
•  Wide  stretches a 4:3 aspect ratio picture to the edges 
of the screen. Since the picture is being stretched, the 
display image may appear distorted. If the program 
is already formatted for widescreen viewing (1.85:1 or 
2.35:1), then black bars will appear on the top and 
bottom of the display image.
•  Zoom  expands images with black bars to fit the screen.
•  Panoramic  expands the display image to fill the screen. 
Images may appear wider than intended. If you are 
watching widescreen (1.85:1 or 2.35:1) content, black 
bars will still appear on the top and bottom of the display 
image.  This option is only available when the TV is 
displaying a 480i/480p source.