Whirlpool Awe 8629 Programme Chart Manual

							
GB
5019 312 10768
ProgrammeTempe-ratureCareLabels
Max.Load
kg Type of wash / Notes- Respect the manufacturer's recommendations on the care label
Detergents and AdditivesSpecial optionsMax.Spin Speed
rpm
Pre- washMain 
WashSoftenerEcoClean+ Pre-washStartdelayIntensiverinseRinseHoldVariablespin
White Cotton /Antibacterial70 - 95°C6.0Normally to heavily soiled bed linen, table linen and underwear, towels, shirts etc. made of cotton and linen. 
At a temperature of 80ºC or more, this programme eliminates bacteria, ensuring sanitization of 
your laundry. The bacteria removal efficiency has been tested following a similar methodology to 
the NF EN 13697 standard of Nov. 2001.
Yes 2)max.Cotton20 - 60°C6.0
Synthetics20 - 60°C3.0Normally soiled blouses, shirts, overalls etc. made of polyester (Diolen, T
revira), polyamide 
(Perlon, Nylon) or blends with cotton. Yes1000 1)
Daily load20 - 60°C3.0Slightly to normally soiled textiles made of cotton and/or synthetics.–
Yes–––max.
Speed 15’20 - 30°C3.0Refreshes briefly worn outer clothing made of cotton, artificial fibers and blends with cotton. Use lovest recommended detergent amount.–Yes––––max.
AquaEco20 - 40°C2.5Lightly soiled laundry made of synthetic fibres, or synthetics mixed with cotton garments.Saving programme with very low water consumption. Use liquid detergent and the
lowest recommended amount for 3 kg laundry. Do not use softener.–Yes–––––max.
Jeans20 - 60°C5.0Normally soiled cotton jeanswear and garments made of jeanslike material such as trousers and jackets. Yes––max.
SuperEco20 - 60°C6.0
Normally to hevily soiled and robust bed linen, table linen and underwear
, towels, shirts etc. made of cotton and/or linen.Offers highest economy in energy consumption by prolonged wash duration. Ideal to be run 
overnight to additionally profit from the more favourable energy rates. To avoid noise of spinning 
at night, set spin speed to “0” and start spin programme in the morning, or define programme 
start with “Start Delay ” accordingly. Use with maximum load.
–Yes–––max.
Delicates20 - 40°C1.5Curtains and delicate clothing, dresses, skirts, shirts and blouses. Yes–––1000 1)
Wool20 - 40°C1.0Only woollens with a felt-free finish, labelled with the woolmark and identified as machine washable.  This programme (40ºC) is tested and approved by The Woolmark Company for machine washable wool.–
Yes––––1000 1)
Handwash20 - 40°C1.0Textiles made of silk, linen, wool and viscose marked as “handwashable”. This programme 
(40ºC) is tested and approved by The Woolmark Company for handwashable wool.– Yes––––400 1)
Rinse & Spin––6.0Same as the last rinse and the final spin in the “Cotton” programme.–––––max.
Spin––6.0In this programme spinning is intensive. Same as the spin cycle in the “Cotton ” programme.––––––––max.
Drain–––Drain only - no spinning. Alternative method of terminating programme after “Rinse Hold”.––––––––––
A.  Programme selector
B.  “Temperature” button
C.  Temperature display
D.  “ Variable spin” button
E.  “Start delay ” button
F.  Time display
G.  “Start(Pause)” button
Whirlpool is a registered trademark of Whirlpool USA.
H.  Programme sequence indicator
I.  “Door open” indication
J.  “Reset” button
This washing machine is equipped with automatic safety functions which detect and diagnose faults at an early stage and react appropriately:
K.  “Service” indication
L.  “Water tap closed” indication
M.  “Clean filter ” indication
PROGRAMME CHART
:  optional / Yes : dosing required1)  For improved garment care, spin speed is restricted in these programmes.2) Only selectable up to a temperature 60°C.
The wool and handwash cycles of this machine have been tested and approved by The Woolmark Company for the washing of Woolmark garments labelled as “machine wash” or “hand wash”provided that the garments are washed according to the instructions on the garment label and those issued in this programme chart.M0703
A
B
HF
EG
C
D
J
I
K
L
M
 
						

							
5019 312 10768
ProgrammeTemperature(°C)
Load
(kg)Water(l)
Energy
(kWh)Approx. ProgrammeDuration*(hours : minutes)
White Cotton / Antibacterial956.059**1.902:00     Cotton606.0551.142:30     Cotton with Eco***606.0550.903:30Cotton406.0550.702:30Synthetics603.054**0.901:40Synthetics403.0480.551:25Daily load403.0400.451:00Speed 15’303.0300.150:15AquaEco402.5190.451:00Jeans405.0700.702:35SuperEco606.0550.784:00Delicates401.5500.550:45
Wool401.0550.550:45Handwash401.0400.550:35
CONSUMPTION DATA
Whirlpool is a registered trademark of Whirlpool USA.
Add detergent as indicated an the front page and as described in the chapter “Detergent and Additives” in your Instructions for Use.1.  Turn the programme selector to the desired
  programme. The display shows the programme
  duration in hours and minutes as well as the
  predefined temperature. The  “Start/Pause”
 button
  flashes.
2.  The 
temperature can be altered by pressing the
  “Temperature” button.
3.  The indication lamp of the predefined 
spin speed
  lights up; in case you want to set another spin speed,
  press the “Variable spin” button.
Consumption values were measured in normalized conditions in compliance with standard IEC/EN 60 456. Consumption data in the home may vary with respect to the values in the table in relation to the water supply pressure and temperature, the load and the type of wash.*  The remaining time indicator can deviate from the values in the table, because it takes into account the household conditions applicable 
  at that time.
**  To reduce the water temperature, some cold water is added at the end of the main wash cycle, before the pump drains the water out.
***  Reference Programme for Energy Label.
ADD DETERGENTS, CLOSE THE LID AND SELECT THE PROGRAMME
“DOOR OPEN” INDICATION
Before starting and after end of a programme, the lamp lights to show the the lid can be opened. As long as a wash programme is running, the lid remains locked and must on no account be forced open. In case you have an urgent need to open it during a running programme, refer to “Cancel a running programme before the end”.
RED INDICATIONS
“Service”Lighting up of the “Service” indication can be caused 
by a fault in an electrical component. Refer to the 
“Troubleshooting Guide” in your “Instructions for Use”; 
if the fault persists, contact our After Sales Service.
“Water tap closed”
The appliance has no or insufficient water supply. Open 
the water tap: if the indications still lights up, refer to the 
“Troubleshooting Guide” in the Instructions for Use.
“Clean pump”
Waste water is not pumped out. Check whether the 
drain hose is kinked or the filter must be cleaned: in the 
latter case refer to the Instructions for Use (“Removing 
the Filter”).
•  Selectable for programmes “Cotton” and
  “Synthetics”; choose temperature of 30 or 40°C and
  use with maximum load.
•  Add an appropriate amount of in-wash additive for
  stain removal (powder) to the main wash chamber,
  together with your detergent (only use powder
  detergent with this option). Respect the
  manufacturer’s dosing instructions.
•  Prolongs the programme by approx. 5 to 15 minutes.
•  Appropriate for use of stain removers and bleaches
  on oxygen basis. 
Chlorine or perborate bleaches
  must not be used!
“Prewash” button
•  Only for heavily soiled loads (for example sand,
  granular dirt) sensible. Increases the cycle time by
  approximately 15 min.
•  Do not use liquid detergent for the main wash when
  activating the Prewash option.
“Intensive Rinse” button•  More water is added and rinse cycle is prolonged.•  This option is particularly suitable for areas with very
  soft water, washing baby linen and helping people
  with allergies.
“Rinse Hold” button
•  The laundry remains in the last rinse water without
  progressing to the final spin cycle to avoid creasing
  and prevent colours from changing.
•  This option is particularly recommended for the
  programmes “Synthetics”, “Daily load” and 
  “Delicates”.
• It is particularly useful if you want to postpone
  spinning to a later time, or if you want to drain only.• If you select “Rinse Hold”, do not leave items to
  soak for too long.
PROGRAMME START
Open the tap and press the  “Start/Pause” button. The indication lamp next to the  “Start/Pause” button lights up. The programme sequence indicator shows the current programme phase, running from left to right 
through Wash, Rinse, Spin/Drain. 
The display shows the remaining programme time. Due 
to variations in load and temperature of inlet water, the 
remaining time is newly calculated in certain programme phases. If this is the case, an animation appears on the time display.
PROGRAMME END
•  All the lights of the programme sequence indicator
  are off, and the “Door open” indication lights up.
1.  Turn the programme selector to the “Off/O”
  position.
2.  Close the water tap.
3.  Open lid and drum and unload the machine.
4.  Leave the lid open for some time to allow the
  interior of the machine to dry.
CHANGE PROGRAMME AND/OR OPTIONS 
AFTER PROGRAMME START
1.  Press the “Start/Pause” button to pause the
  programme. The light flashes.
2.  Select the new programme, temperature, any
  options and another spin speed if you want.
3.  Press the  “Start/Pause” 
button again. The new
  programme continues at the same position where
  the previous programme was interrupted. Do not
  add detergent for this programme.
CANCEL A RUNNING PROGRAMME BEFORE THE END
The  “Reset” button cancels a programme before the end.• Press the  “Reset” button for at least 3 seconds;
  “rES” appears on the display. Any existing water is
  drained out before the lid can be opened.
SELECT ANY DESIRED OPTION
Push the button(s) of any option(s) desired - the respective indication lights up.When the combination of programme and additional option(s) is not possible, the indication lights switch off 
automatically. Unsuitable combinations of options are 
deselected automatically.
“Eco” button•  With modified temperature profile and a slightly
  prologned washing duration, the optimum
  combination of excellent washingresult and even
  lower energy consumption is achieved.
“Clean+” button
•  Choose this option if you use an in-wash additive for
  stain removal ( powder, for example “Vanish”) - it
  will optimize the additive’s efficiency to get better
  wash performance and stain removal.
START DELAY
The “Start delay ” button allows to run the machine at the consumer's convenience, for example at night when 
electricity is cheaper. Do not use liquid detergent when 
activating the “Start delay ”.
•  Select programme, temperature and options.
•  Press the “Start Delay ” button to select the delay
  time up to 23 hours;
•  Press the  “Start/Pause”
 button.
  The indication light over the “Start delay ” button
  flashes and the countdown of the delay time begins.
  The dot between hours and minutes of the delay
  time indicated flashes.
•  The time delay indication disappears when the
  programme starts and it is replaced by the remaining
  programme time.
•  Once having pressed the  “Start/Pause”
 button,
  the number of hours preselected can be reduced by
  pressing and holding the “Start delay ” button. From
  1 hour on, the delay time can also be reduced in
  steps of 10 minutes
.
To cancel the “Start delay ”
..before you press the “Start/Pause” button:
•  Turn the programme selector to another position
  or press the  “Reset” button.
..after having pressed the “Start/Pause” button:
•  Press the  “Reset” button for at least 3 second - the
  start delay time dissapears from the time display.
 Note: The programme stops to “Rinse hold” at the
  time the “Rinse hold” light in the programme
  sequence indicator is on. The indication lamp next to   the  “Start/Pause”
 button flashes.
Terminate the “Rinse Hold” option:
•  Press the  “Start/Pause” button; the programme
  will terminate automatically with the final spin cycle
  for the present wash programme.
•  If you do not wish to spin the clothes, turn the
  programme selector knob to the “Drain”
  programme and press the  “Start/Pause”
 button.
“ Variable spin” button
•  Every programme has a predefined spin speed.
•  Press the button to set another spin speed.
•  If spin speed “0” is selected, the final spinning is
  cancelled but intermediate spin peaks remain during
  the rinse. The water is drained out only.