Whirlpool Awg 910 E Programme Chart Manual

							AWG 908 E / AWG 910 E  PROGRAMME CHART
5019 301 20130
Whirlpool is a registered trademark of Whirlpool USA

: optional / Yes : dosing required1)
For improved garment care, spin speed is restricted in these programmes.
The “wool” programme of this washing machine has been approved by The Woolmark Company for the washing of 
garments labelled as “machine washable”. Follow the instructions given on the label sewn on the garment and the 
instructions supplied by the washing-machine manufacturer. (Cert. no. M0402-M0403-M0404-M0405).
Programme
Te m p e -
rature
Care 
Labels
Max.
Load
kg
Type of wash/Notes
- For temperature selection, respect the manufacturer’s 
recommendations on the care label
Detergents and additives
Special functions
Max.
spin
speed
rpm
Pre
wash
Main
wash
Softener
Pre
wash
Start 
delay
Easy 
Ironing
Intensive
rinse
Rinse
hold
Va r i a bl e
spin
White Cotton
Antibacterial
75 - 90 °C
5.0Normally to heavily soiled bed linen, table linen and 
underwear, towels, shirts etc. made of cotton and 
linen.
At a temperature of 80°C or more, this programme 
eliminates bacteria, ensuring sanitization of your 
laundry. The bacteria removal efficiency has been 
tested following a similar methodology to the NF EN 
13697 standard of Nov. 2001.


Ye s



 
 
—


Max.
Cotton
60 °C
5.0
30 - 40 °C
 
5.0
Synthetics
30 - 60 °C
 
2.5Normally soiled blouses, shirts, overalls etc. made of 
polyester (Diolen, Trevira), polyamide (Perlon, Nylon) 
or blends with cotton.


Ye s



 
 
 
 

800
1)
Delicates
30 - 40 °C
 
2.5Curtains and delicate clothing, skirts, shirts and 
blouses.
—
Ye s

—

——



500
1)
Wool
30 - 40 °C
1.0Only woollens labelled with the Woolmark and 
identified as machine washable. 
This programme (40°C) is tested and approved by The 
Woolmark Company for handwashable wool.
—
Ye s

—

——



800
1)
Lingerie
——
2.5Curtains and delicate clothing in wool or silk only 
washable in cold water.
—
Ye s

—

——



500
1)
Handwash
30 °C
2.0Garments made of linen, silk, wool and viscose marked 
as “handwashable”.
—
Ye s

—

——



800
1)
Quick wash
35 °C
2.5Outer clothing worn for short periods and made of 
cotton, polyester, polyamide and cotton blends.
—
Ye s

—

———


Max.
Daily load
40 °C
 
3.5Slightly to normally soiled garments made of cotton 
and/or synthetics.


Ye s



 
 
—


Max.
Cold wash
——
5.0Slightly soiled garments in cotton and/or synthetics 
washable only in cold water.
—
Ye s

——


—


Max.
Rinse
——
5.0Same as the last rinse and the final spin in the “Cotton” 
programme.
——

—

—

—


Max.
Drain
Spin
——
5.0In this programme spinning is intensive. Same as the spin 
cycle in the “Cotton” programme.
————

———


Max.









	


This washing machine is equipped with 
automatic safety functions which 
detect faults at an early stage and react 
appropriately, e.g.:
A. “Service” indicator
B. “Clean Pump” indicator
C. “Water Tap Closed” indicator
D. “Door lock” indicator
E. Programme selector
F. “Start” button
G. “Variable spin” button
H. The programme sequence indicator 
/ Start delay time indicator
O. Optional function buttons
J. “Start delay” button
30120130GB.fm  Page 1  Wednesday, August 8, 2007  10:16 AM
Black process 45.0° 150.0 LPI 
 
						

							5019 301 20130
Whirlpool is a registered trademark of Whirlpool USA
Add detergent as indicated on the front page and as 
described in the chapter “Detergent and Additives” 
in the Instructions for Use.
1. Turn the 
programme selector to the desired 
programme.
2. The indicator of the predefined 
spin speed 
lights up; in case you want to set another spin 
speed, press the “Variable spin” button .
Press the button(s) of any required option(s) - the 
respective indicator lights up.
When the combination of programme and 
additional option(s) is not possible,
the indicators switch off automatically. Unsuitable 
combinations of options are deselected automatically.
“Prewash” button 
 Only for heavily soiled loads (e.g. sand, granular dirt). 
Increases the cycle time by approx. 15 minutes.
 Do not use liquid detergent for the main wash 
when activating the prewash option.
“Easy Ironing” button 
 Can be used together with “Cotton”, 
“Synthetic” and “Daily load” programmes to 
make ironing easier.
 Increases the water quantity and the clothes are 
spun very gently.“Intensive rinse” button
 More water is added and the rinse cycle is 
prolonged.
 This option is particularly suitable for areas with 
very soft water, washing baby linen, and helps 
people with allergies.
“Rinse hold” button
 The laundry remains in the last rinse water 
without the final spin cycle, to avoid creasing and 
prevent colours from changing.
 This option is particularly recommended for the 
“Synthetics”, “Daily load” or “Delicates” programmes.
 It is particularly useful if you want to postpone 
spinning to a later time, or if you want to drain only.
 If you select “Rinse hold”, do not leave the 
laundry to soak for too long.
Note: The programme stops to “Rinse hold” at 
the time the “Rinse Hold” light in the programme 
sequence indicator is on. The indicator next to 
the 
“Start”
  
button flashes.
To terminate the “Rinse hold” option  :
Press the 
“Start” button; the programme 
will terminate automatically with the final spin 
cycle for the preset wash programme.
“ Variable spin” button
 Every programme has a predefined maximum 
spin speed.
 Press the button to set another spin speed.
 If spin speed “0” is selected, the final spin is 
cancelled but intermediate spin peaks remain 
during rinse. The water is drained out only.
CONSUMPTION DATA
Programme
Te m p e r a t u r e
(°C)
Load
(kg)
Wa t e r
(l)
Energy
(kWh)
Approx. programme duration
(hours : minutes)
*
White Cotton / Antibacterial 90 5.0 52
**1.70 2:10
Cotton 75 5.0 52 1.33 2:05
Cotton with “Eco”
***60 5.0 49 0.95 2:15
Cotton 40 5.0 62 0.51 2:00
Synthetics 60 2.5 46
**0.80 1:40
Synthetics 40 2.5 46 0.46 1:35
Daily load 40 3.5 52 0.30 1:25
Quick wash 35 2.5 30 0.40 0:40
Delicates 30 2.5 54 0.24 0:45
Wool 40 1.0 56 0.44 0:54
Handwash 30 2.0 65 0.24 0:57
Consumption values were measured in normalized conditions in compliance with standard IEC/EN 60 456. In domestic use, consumption data 
may vary with respect to the values in the table in relation to the water supply pressure and temperature, the load and the type of wash.
*The time indicated on the display (if present) can deviate from the values in the table, because it takes into account the household 
conditions applicable at that time.
**To reduce the water temperature, some cold water is added at the end of the main wash cycle, before the pump drains the water out.
***Reference programme for energy label.ADD DETERGENTS, CLOSE THE DOOR 
AND SELECT THE PROGRAMMESELECT ANY DESIRED OPTION
The “Start Delay”   option allows you to 
programme machine activation at a later stage, for 
example at night when electricity is cheaper. Do not 
use liquid detergent when activating the “Start delay”.
 Select the programme and options.
 Press the “Start Delay ” button to select 
programme start a delay time of 1 to 12 hours;
Press the 
“Start” button . 
The indicator next to the 
“Start Delay ” button 
lights up, whereas the selection indicator flashes 
to signal the countdown of the remaining time.
 At the end of the delay time the machine starts 
the set programme. The LED indicating the 
wash stage in progress lights up.
 After pressing the 
“Start” , the number of 
hours preselected can be reduced by pressing 
and holding the “Start Delay ” button.
To cancel the “Start Delay ”:
Press the 
“Start Delay ” button until all the indicator 
lights are off. The selected programme will then start.
Open the tap and press the 
“Start”. The 
indicator next to the 
“Start” button lights up. 
The programme sequence indicator shows the 
current programme stage, running from left to right 
through Prewash, Wash, Rinse, Spin/Drain, End.
At the end of a programme, the 
“End” indicator 
lights up signalling that the door can be opened. As 
long as a wash programme is running, the door 
remains locked and must not be forced open. In 
case you have an urgent need to open it during a 
running programme, refer to “Cancel (Reset) a 
running programme before the end”.
“Service” indicator
Lighting up of the “Service” indicator can be caused by 
a fault in an electrical component. Refer to the 
“Troubleshooting Guide” in the Instructions for Use; If 
the fault persists, contact our After-Sales Service.“Clean pump” indicator
The water is not pumped out. Check whether the 
drain hose is kinked or the filter must be cleaned; in 
the latter case refer to the Instructions for Use 
(“Removing the filter”).
“Water tap closed” indicator
Machine water supply insufficient or lacking. Open 
the water tap; Turn the programme selector to 
“Off/0” and reset the programme. If the indicator 
remains on, refer to the “Troubleshooting Guide” in 
the Instructions for Use.
“Door lock” indicator
Lighting up of the indicator could be caused by the 
door not being properly closed. Try closing it again. 
Turn the programme selector to “Off/0” and reset the 
programme. If the indicator remains on, refer to the 
“Troubleshooting Guide” in the Instructions for Use.
 Lighting up of the lamp on the wash sequence 
indicator means that the programme has ended 
and the door is unlocked.
1. Turn the programme selector to the “Off/O” 
position.
2. Close the water tap.
3. Open the door and unload the machine.
4. Leave the door ajar to allow the drum to dry.
1. Turn the programme selector to “Off/O”.
2. Select the new programme, any options and 
another spin speed if you want.
3. Press the
 “Start” button   again. The new 
programme resumes the wash programme from 
where the previous one was interrupted. Do not 
add detergent for this programme.
 Reset by turning the programme selector to 
“Off/0” and select the “Drain Spin” programme 
to remove the water remaining in the bowl 
before the door can be opened.START DELAYPROGRAMME START“DOOR OPEN” INDICATORRED INDICATORS
PROGRAMME ENDCHANGING PROGRAMME AND/OR 
OPTIONS AFTER PROGRAMME STARTCANCEL (RESET) A RUNNING 
PROGRAMME BEFORE THE END
30120130GB.fm  Page 2  Wednesday, August 8, 2007  10:16 AM
Black process 45.0° 150.0 LPI