Whirlpool Awm 6080 Programme Chart Manual

							5019 301 10137
Whirlpool is a registered trademark of Whirlpool USA
Programme
Care
Labels
Type of wash/Notes
Max 
Load
Kg
Detergents and additives
Special options
Max
Spin
Speed
rpm
Temperature
Selector
°C
Programme
Selector
Bleach
Softener
Main 
Was h
Pre-
wash
Easy
Ironing
Prewash
Intensive
Rinse
Rinse
Hold
Spin Speed
Reduction
Cotton/
Coloured cotton
  
 
Normally to heavily soiled bed linen, table linen and underwear, towels, shirts 
etc. made of cotton and linen.
With heavily soiled laundry the additional “Prewash” option can be selected as well.
5.0
❉❉
Ye s
❉❉ ❉ ❉ ❉ ❉
800
Max. 95°
Synthetics
  
Normally soiled blouses, shirts, overalls etc. made of polyester (Diolen, Trevira), 
polyamide (Perlon, Nylon) or blends with cotton.
2.5
—
❉
Ye s
❉❉ ❉ ❉ ❉
❉
1)
600
1)
Max. 60°
Daily
 
Slightly to normally soiled textiles made of cotton and/or synthetics.
3.0
—
❉
Ye s —
❉
—
❉❉❉
800
Max. 60°
Rapid PlusShortly worn outer clothing made of cotton, polyester, polyamide and blends 
with cotton.
3.0
—
❉
Ye s —
❉
—
❉❉❉
800
Max. 30°
Delicates
 
Curtains and delicate clothing, dresses skirts, shirts and blouses.
1.5
—
❉
Ye s
❉
—
❉
—
❉
❉
1)
600
1)
Max. 40°
WoolOnly woollens with a felt-free finish, labelled with the woolmark and identified as 
machine washable.
If you select “Rinse Hold” do not leave items to soak for too long.
1.0
—
❉
Ye s —
—— —
❉
❉
1)
600
1)
Max. 40°
HandwashTextiles made of linen, silk, wool and viscose marked as “handwashable”.
If you select “Rinse Hold” do not leave items to soak for too long. A very gentle spin is 
used in this programme.
1.0
—
❉
Ye s —
—— —
❉
❉
2)
400
2)
Max. 30°
Rinse + spin —Same as the last rinse and the final spin in the “Coloured Cotton” programme.
5.0
—
❉
——
❉
—
❉❉❉
800 —
Spin —In this programme spinning is intensive. Same as the spin cycle in the “Coloured 
Cotton” programme.
5.0
—
———— — — —
❉
800 —
Gentle spin —In this programme spinning is gentle. Same as the spin cycle in the “Wool” 
programme.
1.5
—
———— — — —
❉1)
600
1)
—
Drain —Drain only - no spinning. Alternative method of terminating programme after “Rinse 
Hold”.
——
———— — — — —
—
—
A. Programme Sequence Indicator
B. “Start/Pause” Button
C. “Door Open” Indication
D. Temperature Adjusting Buttons
E. “Spin Speed Reduction” ButtonSelecting any option the indication lights up.
When the combination of programme, 
additional options and temperature is not 
possible, the indication lights switch off 
automatically. Unsuitable combinations of 
options are deselected automatically.
❉ : optional / Yes: dosing required1For improved garment care spin speed is restricted to 
600 rpm in this programme.2In this programme default spin speed can be increased 
till 400 rpm. 
B
AC
E
D
AWM 6080
GBPROGRAMME CHART
 
						

							5019 301 10137
Whirlpool is a registered trademark of Whirlpool USA
Prewash might increase programme duration. Consumption values were measured in normalized conditions in compliance 
with Standard IEC 60 456. Consumption data in the home may vary with respect to the values in the table in relation to the 
water supply pressure and temperature, the load and the type of wash.
* The remaining time indicator can similarly deviate from the values in the table, because it takes into account the household 
conditions applicable at that time.
** To reduce the water temperature, some cold water is added at the end of the main wash cycle, before the pump drains the 
water out.Add the detergent as described in the programme 
table or in the chapter “Detergents and Additives” in 
the booklet.
1. Turn the programme selector to the desired 
programme.
2. The “Start/Pause”
 button is flashing.
3. Select the temperature by pressing “+” or “-” 
button below the temperature display.
4. Select the spin speed by pressing the spin speed 
button - the selected spin speed is indicated by 
the indication next to it.
5. Select any desired option by pressing the option 
button.Selecting any option the indication lights up.
When the combination of options, temperature 
and spin speed is not possible, the indication 
lights switch off automatically. Unsuitable 
combinations of options are deselected 
automatically.
“Easy Ironing” button
 Can be used together with with Cotton, 
Synthetics, Daily and Rapid Plus programmes to 
make ironing easier.
 Increases the water quantity and the clothes are 
spun very soft.
“Prewash” button
 Only for heavily soiled loads (for example sand, 
granular dirt) sensible. The cycle time increases 
approximately 15 min.
“Intensive Rinse” button
 More water and a longer time in rinse cycle is added.
 This option is particularly suitable for areas with 
very soft water, washing baby linen and helps 
people with allergies.CONSUMPTION DATA
Programme
Temperature 
Selector
(°C)
Load
(kg)
Wa t e r
(l)
Energy
(kWh)
Approx.
Programme
Duration
(hours : minutes)*
Cotton 95 4.5 49** 1.70 2:05
Cotton 60 5.0 46 0.95 2:20
Cotton 40 4.5 44 0.60 2:05
Synthetics 60 2.0 55 0.80 1:30
Synthetics 40 2.0 55 0.60 1:20
Daily 40 3.0 40 0.50 1:00
Rapid Plus 30 3.0 37 0.40 0:30
Delicates 30 1.5 60 0.50 0:45
Wool 30 1.0 60 0.30 0:40
Handwash 30 1.0 60 0.30 0:50
ADD DETERGENTS, CLOSE THE DOOR AND 
SELECT THE PROGRAMME
SELECT ANY DESIRED OPTION
“Rinse Hold” button
 The laundry remains in the last rinse water 
without progressing to the final spin cycle to 
avoid creasing and prevent colours from 
changing.
 This option is particularly recommended for the 
programme “Synthetics”, “Daily ” and 
“Delicates”.
 This function is particularly useful if you want to 
postpone spinning to a later time, or if you want 
to drain only.
Note:
 The programme stops to “Rinse Hold” at 
the time the “Rinse Hold” light in the programme 
sequence indication is on.
Terminate the “Rinse Hold” option:
 Press the “Rinse Hold” button again; the 
programme will terminate automatically with 
the final spin cycle for the present wash 
programme.
 If you do not wish to spin the clothes, turn the 
programme selector knob counter-clockwise to 
the Drain programme and press the 
“Start/Pause” 
button again when flashing. You 
have to press “Start”
 button within 15 seconds 
after reselecting the programme.
“Spin Speed Reduction” button
 Every programme has an automatic predefined 
maximum spin speed.
 Press the button to set another spin speed.
 If the spin speed “0
” is selected, the final 
spinning is cancelled but intermediate spin peaks 
remain during rinse. The water is drained out 
only.
Open the tap and press the “Start/Pause”
 button. 
The “Start/Pause”
 button lights up. The indicator 
lamps show the sequence reached in the 
programme. After starting the programme, the 
sequence indication runs from left to right through 
Wash, Rinse, Spin.
When the sequence of the programme is finished 
the corresponding lamp goes out.The door can be opened when the “Door Open” 
indication is on.
 All the lights of the programme sequence 
indication are off.
1. Turn the programme selector to the “0” - “Off” 
position.
2. Turn the water supply tap off.
3. Open the door and unload the machine.
4. Close the tap and leave the door ajar to allow 
the drum to dry out.
1. Press the “Start/Pause”
 button to pause the 
programme. The light flashes.
2. Select the new programme (with 
temperature), any options and another spin 
speed if you want.
3. Press the “Start/Pause”
 button again. 
The new programme continues at the same 
position where the previous programme was 
interrupted. Do not add detergent for this 
programme.
1. Press the “Start/Pause”
 button to pause the 
programme. The light flashes.
2. Set the programme selector to “Drain”. 
The spin speed indicators show “0
”.
3. Press the “Start/Pause”
 button to start the 
drain programme.PROGRAMME START
DOOR LOCKPROGRAMME ENDCHANGE THE PROGRAMME, OPTIONS 
AFTER PROGRAMME STARTCANCEL A PROGRAMME BEFORE THE END