Whirlpool Awod 050 Programme Chart Manual

							
GB 
5019 301 01107
ProgrammeCareLabelsMax.Load
kgType of wash / Notes- respect the manufacturer's recommendations on the care label
Detergents and AdditivesSpecial optionsMax. Spin Speed
rpm
Pre- 
washMain 
WashSoftenerCold washRinsehold
Cotton with prewash95 °C6.0Heavily soiled, long wearing and temperature stable textiles in cotton and linen (bed linen, table 
linen, underwear, shirts etc.). Yes
Yes 1)–Max.
Cotton60 - 95 °C6.0
Normally to heavily soiled bed linen, table linen and underwear, towels, shirts etc. made of cotton 
and linen.–YesMax.Cotton40 °C5.0
Synthetics with prewash60 °C2.5 Heavily soiled blouses, shirts, overalls etc. made of polyester (Diolen, T
revira), polyamide (Perlon, Nylon) or blends with cotton. Yes
Yes 1)–1000 2)
Synthetics30 - 40 - 60 °C2.5 Normally soiled blouses, shirts, overalls etc. made of polyester (Diolen, T
revira), polyamide 
(Perlon, Nylon) or blends with cotton.–Yes1000 2)
Delicates30 °C1.5Curtains and delicate clothing, dresses, skirts, shirts and blouses.–Yes1000 2)
Quick wash30 °C3.0 Shortly worn outer clothing made of cotton, polyester, polyamide and blends with cotton.–YesMax.
WoolCold - 40 °C1.0Only woollens with a felt-free finish, labelled with the woolmark and identified as machine washable.–Yes1000 2)
Handwash30 - 40 °C1.0Textiles made of linen, silk, wool and viscose marked as “handwashable”. A very gentle spin is used in this programme.–Yes400 2)
Rinse & Spin–6.0
Same as the last rinse and the final spin in the “Cotton” programme.–––Max.
Spin–6.0In this programme spinning is intensive. Same as the spin cycle in the “Cotton ” programme.–––––Max.
Gentle Spin–1.0In this programme spinning is gentle. Same as the spin cycle in the “ Wool” programme.–––––1000 2)
Drain––Water is drained only without any spinning. Alternative method of terminating programme after “Rinse Hold”.––––––
A. “Door open” indication
This washing machine is equipped with 
automatic safety functions which detect 
and diagnose faults at an early stage 
and react appropriately, e.g.:
B. “Service” indication
C. “Water tap closed” indication
D. “Clean pump” indication
Whirlpool is a registered trademark of Whirlpool USA.
E. Programme selector
F. “Start/Pause” button
G. Programme sequence indicator
H. “Reset” button
AB
 :   option / Yes : dosing required1)    Do not use liquid detergents.2)    For improved garment care spin speed is restricted in these programmes.
PROGRAMME CHART
H
FE
G
CD
 
						

							
5019 301 01107
ProgrammeTemperatureSelector
(°C)
Load
(kg)Water(l)
Energy
(kWh)Approx. Programme
Duration
(hours : minutes)
Cotton956.059 *1.902:00
   Cotton **606.0491.022:20
Cotton405.0560.702:00
Synthetics602.550 *0.801:35
Synthetics402.5460.501:20
Delicates301.5600.500:41
Quick wash303.0410.400:30
Wool
401.0600.500:46
Handwash401.0450.500:41
Add detergents as indicated on the front page and as described in your Instructions for Use. 
Close the door and turn the  programme selector to the desired programme and temperature. The indication lamp next to the  “Start/Pause” button flashes.
CONSUMPTION DATA
Consumption values were measured in normalized conditions in compliance with standard IEC/EN 60 456. Consumption data in the home may vary with respect to the values in the table in relation to the water supply pressure and temperature, the load and the type of wash.* To reduce the water temperature, some cold water is added at the end of the main wash cycle, before the pump drains the water out.
**  Reference Programme for Energy Label.
ADD DETERGENTS, CLOSE THE DOOR AND SELECT THE PROGRAMME
“DOOR OPEN” INDICATION
Before starting and after end of a programme, the lamp lights to show the the door can be opened. As long as a wash programme is running, the door 
remains locked and must on no account  be forced  
open. In case you have an urgent need to open it during a running programme, refer to “Cancel 
(Reset) a running programme before the end”.
RED INDICATIONS
“Service”Lighting up of the “Service” indication can be caused by a fault in an electrical component. 
Refer to the “Troubleshooting Guide” in your 
“Instructions for Use”; if the fault persists, contact our After Sales Service.
“Water tap closed”
The appliance has no or insufficient water supply. Open the water tap: if the indications still lights 
up, refer to the “Troubleshooting Guide” in the 
Instructions for Use.
“Clean pump”
Waste water is not pumped out. Check whether the drain hose is kinked or the filter must be cleaned: in the latter case refer to the Instructions 
for Use (“Removing the Filter”).
“Rinse hold” button•  The laundry remains in the last rinse water       
  without progressing to the final spin cycle to 
  avoid creasing and prevent colours from changing.•  This option is particularly recommended for 
  the programmes “Synthetics” and “Delicates”.
•  It is particularly useful if you want to postpone
  spinning to a later time, or if you want to drain 
  only.
• If you select “Rinse hold” do not leave items to 
  soak for too long.
 Note: The programme stops to “Rinse hold” 
  at the time the “Rinse hold” light in the 
  programme sequence indication is on.  
  The indication lamp next to the  “Start/Pause”
 
  button flashes.
Terminate the “Rinse hold” option:
•  Press the  “Start/Pause”  button; the programme 
  will terminate automatically with the final spin 
  cycle for the present wash programme.
•  If you do not wish to spin the clothes, turn the
  programme selector knob to the “Drain”
  programme and press the  “Start/Pause”       
  button
.
Whirlpool is a registered trademark of Whirlpool USA.
PROGRAMME START
Open the tap and press the  “Start/Pause” button. The indication lamp next to the “Start/
Pause” 
button lights up. The programme sequence indicator shows the current programme 
phase, running from left to right through Wash, 
Rinse, Spin/Drain. When the programme phrase is finised, the corresponding indication goes out.
PROGRAMME END
•  All the lights of the programme sequence 
  indicator are off, and the “Door open” indication 
  lights up.
1. Turn the programme selector to the “Off/O”
  position.
2. Close the water tap.3. Open the door and unload the machine.4. Leave the door ajar to allow the drum to dry.
CHANGE PROGRAMME AND/OR OPTIONS 
AFTER PROGRAMME START
1. Press the  “Start/Pause” button to pause the
  programme. The light flashes.
2. Select the new programme (with temperature), 
  any options and another spin speed if you want.
3. Press the  “Start/Pause” button again. 
  The new programme continues at the same 
  position where the previous programme was 
  interrupted. Do not  add detergent for this 
  programme.
CANCEL (RESET) A RUNNING PROGRAMME BEFORE THE END
The  “Reset” button cancels a programme before the end.•  Press the  “Reset” button for at least 3 seconds.
  Any existing water is drained out before the 
  door can be opened.
SELECT ANY DESIRED OPTION
Push the button(s) of any option(s) desired - the respective indication lamp lights up.When the combination of programme and additional option(s) is not possible, the indication 
lights switch off automatically. Unsuitable 
combinations of options are deselected 
automatically.
“Cold wash” button•  With this option, water is heated only up to 20ºC.•  Suitable for delicate laundry items with wash
  temperature recomendation of max. 30ºC on the
  care label.
• Selectable only on the lowest temperature 
  step of each programme.