Xerox 6279 User Manual

2.Move the printer Power switch to the On position (up).
3.Press the Power button on the front of the Controller to turn it on.
The Power button indicator will illuminate. The Control Panel will display the message
“Printer Warming Up”. The machine will be print-ready in about 3 minutes.
System Power Off Procedure
CAUTION
Powering down the system incorrectly may result in data corruption and a service
call.
The system shutdown selection allows the Controller to power down correctly. System
Shutdown is...

Shutdown from the User Interface
NOTE
Many of the features within the Administration tab require a password for access.
See your System Administrator for the password prior to getting started unless
the Administrator mode is already active.
NOTE
System Shutdown and Restart is used to reboot the system. This option will
not completely shut down the controller
1.Select Machine Info from either the Services menu, or by pressing the Machine Info
button located on the Control Panel.
2.Select the...

2.Select Utilities > Shutdown > Shutdown.
NOTE
Do not select Restart Controller. It is used to reboot the system when jobs in
the print queue fail to process correctly. Rather, wait for the system to shut down.
3.Move the printer Power Switch to the Off (down) position.
1-17Xerox® 6279® Wide Format Solution
Printer User Guide
Product Overview
Downloaded From ManualsPrinter.com Manuals 

4.Move the printer Circuit Breaker switch to the Off (down) position.
Checking the Circuit Breaker
The Circuit Breaker opens automatically and removes input power from the machine if
a short circuit or current condition occurs.
When the Circuit Breaker Switch is in the up position, input power is supplied to the
machine. If the machine will not be used for an extended amount of time, the printer
and controller may be powered down.
Check the Circuit Breaker once a month for correct operation. If you...

About Media and Originals
This section describes the kinds of media which are available for this machine, as well
as the appropriate media handling, loading and storage procedures.
The use of inappropriate media may result in media jams, reduced print quality,
malfunctions and other problems. To make the most effective use of the machine, we
suggest that you use only the media recommended by Xerox.
There are several configurations of the 6279 Wide Format Printer for media input. The
standard is a one...

Media Types and Weights
Table 11: Media Types and Weights
NACO WeightEO WeightTypeMedia Source
18-20 lb
90-112 gsm
4 mil
18 lb
60-110 gsm
90-112 gsm
75- 100 µm
Bond
Tracing Paper
Film
T-Bond
Roll
18-20 lb60-110 gsmBondTray
18-20 lb
90-112 gsm
4 mil
18 lb
60-110 gsm
90-112 gsm
75-100 µm
Bond
Tracing Paper
Film
T-Bond
Manual
Feed-in Shelf
NOTE
G.S.M. (g/m2) is a measure of a substance/weight of a paper expressed in grams
per square meter, which does not depend on the number of sheets in the ream.
Roll...

Tray Media Sizes
Table 13: Tray Media Sizes
Media Tray SizesSize Series
Landscape/Portrait (8.5”x11”)
Landscape/Portrait (11”x17”)
Landscape (17”x22”)
ANSI
Landscape/Portrait (9”x12”)
Landscape/Portrait (12”x18”)
Landscape (18”x24”)
ARCH
A4/Landscape/Portrait (210X297mm)
A3/Landscape/Portrait (297x420mm)
A2/Landscape (420x594mm)
ISO A (JIS)
B3/Landscape/Portrait
B4/Landscape/Portrait
ISO B
B3/Landscape/Portrait
B4/Landscape/Portrait
JIS B
Manual Feed-in Shelf (Bypass) Sizes
Table 14: Manual Feed-In Shelf...

Storing Media
The optimum environment in which to store paper media is a humidity of 40 to 45%.
Keep the following in mind when storing paper media:
•Moisture is not good for media. For storage, wrap the media in wrapping paper and
store it in a comparatively dry place. Tracing paper, especially, should be put in a
plastic or moisture-proof bag that contains desiccant.
•When the machine is not used for a long period of time, remove the media and store
it appropriately.
•The printer has a paper heater....

2.Lift and remove the Media Roll that needs to be replaced.
3.Pinch the Green Lever at the end of the Media Shaft in the direction of the Media
Size Label to release the roll from the shaft.
NOTE
Pinching the Green Lever releases the spring tension lock, making it possible for
you to remove the shaft from the core.
4.Slowly pull the Media Shaft from the core of the Media Roll.
1-23Xerox® 6279® Wide Format Solution
Printer User Guide
Product Overview
Downloaded From ManualsPrinter.com Manuals 

5.Pinch the Green Lever again to insert the new Media Shaft into a new media roll. Be
sure the roll ends are aligned according to the Media Size Label.
6.Remove the manufacturer’s piece of tape holding the edge of the roll from unraveling.
NOTE
If you see any remaining glue when removing the tape from a new roll, wipe it
clean. This can cause misfeeds.
If the Media Roll is damaged, trim the damaged edge with scissors before proceeding
to the next step.
WARNING
Be careful not to pinch your fingers when...