Xerox Phaser 6120 User Manual

About the Control Panel 34
QUALITY MENU
With this menu, settings for the print quality can be specified.
All factory default values are shown in bold.
TONER 
REMOVALBLACKSettingsYES/NO
When YES is selected, the carousel rotates to the 
black toner cartridge, so that it can be replaced.
For details on replacing the toner cartridge, refer to 
“Replacing a Toner Cartridge” on page 79.
CYANSettingsYES/NO
When YES is selected, the carousel rotates to the 
cyan toner cartridge, so that it can be replaced.
For...

About the Control Panel 35
DENSITY 
CALREQUEST 
CALSettingsNO/YES
If YES is selected, image adjustments are performed.
MODESettingsON/OFF
If ON is selected, the image adjustments are applied.
If OFF is selected, image adjustments are not applied.
DENSITY 
CONTROLBLACKSettings1/2/3/4/5
Adjust the density of the black toner to one of five 
levels.
If 1 is selected, the density is at its lightest level. If 5 
is selected, the density is at its darkest level.
CYANSettings1/2/3/4/5
Adjust the density of the...

About the Control Panel 36
CONNECTION SETUP MENU
With this menu, interface settings can be specified.
Restart the printer after changing settings in the 
NETWORK SETUP menu.
All factory default values are shown in bold.
NETWORK 
SETUPTCP/IPENABLESettingsYES/NO
If YES is selected, TCP/IP is enabled.
If NO is selected, TCP/IP is disabled.
DHCP/
BOOTPSettingsON/OFF
Select whether or not the IP address is 
automatically acquired.
If YES is selected, the IP address is 
automatically acquired.
If NO is...

About the Control Panel 37
SUBNET 
MASKSettings0.0.0.0
Specify the subnet mask for the 
network. Use the Up, Down, Left, and 
Right keys to specify the value.
ENABLE 
HTTPSettingsYES/NO
Specify whether or not HTTP is used.
If YES is selected, the Web page 
provided to the printer by the built-in 
HTTP server is enabled.
If NO is selected, the Web page cannot 
be used.
ENABLE 
AUTO IPSettingsYES/NO
Select whether or not the IP address is 
automatically acquired when DHCP/
BOOTP and PING, ARP are not...

About the Control Panel 38
NETZONESettingsAutomatically 
entered
Specify the Macintosh EtherTalk zone.
The zone name can contain a 
maximum of 16 characters.
NETZONE2SettingsAutomatically 
entered
Specify the Macintosh EtherTalk zone.
The zone name can contain a 
maximum of 16 characters.
ETHERNET 
SPEEDSettingsAUTO/100 FULL DUPLEX/100 
HALF DUPLEX/10 FULL 
DUPLEX/10 HALF DUPLEX
Specify the transmission speed for the network and 
the transmission method for bi-directional 
transmission.
PS...

About the Control Panel 39
SYSTEM DEFAULT MENU
With this menu, settings can be specified to adjust the operation of the printer, 
such as the time until the machine enters Energy Saver mode.
* These menu items appear only if an optional hard disk is installed. 
** This menu item appears only on 110 V units.
All factory default values are shown in bold.
PRINT 
QUALITYSettingsENHANCED/STANDARD
Select the image quality for prints.
COLOR 
MODESettingsCOLOR/GRAYSCALE
Specify whether printing is in full...

About the Control Panel 40
PCLLINE 
TERMINA
TIONSettingsCR=CR LF=CRLF/ 
CR=CR LF=LF/ 
CR=CRLF LF=LF/ 
CR=CRLF LF=CRLF
Select the definitions of the CR/LF codes 
in the PCL language.
FONTPITCH 
SIZESettings44-1000-9999
Specify the bitmap font size in 
the PCL language.
FONT 
NUMBERSettings0-32767
Specify the font used with the 
PCL language.
The font numbers that appear 
correspond to the PCL font 
list. For details on printing the 
font list, refer to 
“PRINTABLE 
PAGES MENU” on page 30.
POINT...

About the Control Panel 41
DATE & 
TIMESettingsyyyymmdd:hhmmss
Set the date and time on the hard disk’s time-of-day clock.
The settings appear in the following order: year, month, day:hour, 
minutes, seconds.
ENERGY 
SAVERSettings15 MINUTES/30 MINUTES/1 HOUR/2 HOURS
Specify the length of time until the machine enters Energy Saver 
mode.
This menu item appears only when ENERGY SAVER is set to ON.
2 Hours is displayed only on 110 volt units.
SECURITYCONFIGUREENABLESettingsOFF/ON
Select whether or not the...

About the Control Panel 42
SERVICE MENU
With this menu, the service representative can adjust the printer and perform 
maintenance operations. This menu cannot be used by the user.
FORMATFORMAT 
FLASHSettingsNO/YES
Select whether or not to initialize the flash RAM.
If YES is selected, the flash RAM is initialized.
FORMAT 
DISKSettingsNO/YES
Select whether or not to initialize the hard disk.
If YES is selected, the hard disk is initialized.
RESTORE /
SAVERESTORE 
FACTORYSettingsNO/YES
Select whether or...

About the Control Panel 43
LANGUAGE MENU
The display language of the message window can be changed to the required 
language. The available languages are:
„English
„Spa nish
„French
„German
„Italian
„Portuguese
„Dutch
„Swedish
The default setting is English.
Downloaded From ManualsPrinter.com Manuals