Zanussi Fcs 1020 C User Manual

Washing programmes
Programme/ TemperatureType of laundryOptionsDescription of the pro-
gramme
COTTON
90°White cotton (heavily
soiled cotton items)
SPIN REDUCTION/NO
SPIN/RINSE HOLD
EXTRA QUICK/QUICK 
1)
PREWASH
ECONOMY
SUPER RINSE
Main wash
Rinses
Long spin max. 1000 rpm
Max load 3 kg
COTTON
60° - COLDColoured cotton (normally
soiled cotton items)
SPIN REDUCTION/NO
SPIN/RINSE HOLD
EXTRA QUICK/QUICK 
1)
PREWASH
ECONOMY
SUPER RINSE
Main wash
Rinses
Long spin max. 1000 rpm
Max load 3 kg
SYNTHETIC
60°-30°...

Programme/ TemperatureType of laundryOptionsDescription of the pro-
gramme
SPIN 
Separate spin for hand
washed garments and after
programmes with the Rinse
Hold option selected. You
can choose the spin speed
by turning the spin speed
selector to adapt it to the
fabrics to be spun.
SPIN REDUCTION
Drain and long spin
Max. spin speed 1000 rpm
Max Load 3 kg
 / OFF
For resetting the pro-
gramme or switching the
machine off
  
1) If you select this option, we recommend that you reduce the maximum load....

Cleaning the drawer recess
Having removed the draw-
er, use a small brush to
clean the recess, ensuring
that all washing powder
residue is removed from
the upper and lower part of
the recess.
Replace the drawer and run the rinse programme with-
out any clothes in the drum.
Cleaning the water inlet filter
If your water is very hard or contains traces of lime deposit,
the water inlet filter may become clogged. It is therefore
a good idea to clean it from time to time.
Turn off the water tap. Un-
screw the...

ProblemPossible cause/Solution
The machine does not start:
The door has not been closed.
• Close the door firmly.
The plug is not properly inserted in the power socket.
• Insert the plug into the power socket.
There is no power at the socket.
• Please check your domestic electrical installation.
The main fuse has blown.
• Replace the fuse.
The selector dial is not correctly positioned and the button Start has not been
pressed.
• Please turn the selector dial and press the button Start again.
The machine...

ProblemPossible cause/Solution
Unsatisfactory washing results:
Too little detergent or unsuitable detergent has been used.
• Increase the detergent quantity or use another one.
Stubborn stains have not been treated prior to washing.
• Use commercial products to treat the stubborn stains.
The correct temperature was not selected.
• Check if you have selected the correct temperature.
Excessive laundry load.
• Reduce the laundry load.
The door will not open:
The programme is still running.
• Wait the end of...

Mod. ... ... ...
Prod. No. ... ... ...
          Ser. No. ... ... ...
Technical data
DimensionsWidth
Height
Depth67 cm
49,5 cm
51,5 cm
Electrical connection
Voltage - Overall power - FuseInformation on the electrical connection is given on the rating plate, on the
inner edge of the appliance door.
Water supply pressureMinimum
Maximum0,05 MPa
0,8 MPa
Maximum LoadCotton3 kg
Spin SpeedMaximum1000 rpm
Consumption values
ProgrammeEnergy consumption
(KWh)Water consumption (litres)Programme duration (Mi-...

ProgrammeEnergy consumption
(KWh)Water consumption (litres)Programme duration (Mi-
nutes)
Spin--~ 5
1) «Cottons + Eco option» at 60°C with a load of 3 kg is the reference programme for the data entered in the energy label, in compliance
with EEC 92/75 standards.
The consumption data shown on this chart is to be considered purely indicative, as it may vary depending on
the quantity and type of laundry, on the inlet water temperature and on the ambient temperature.
Installation
Lifting the machine
Be...

With a suitable spanner unscrew and remove the three
screws and their spacers on machines rear.
The three holes must then
be plugged with the plastic
plug caps supplied in the
bag containing the in-
struction booklet, which
can be found inside the
drum.
Positioning
Install the machine on a flat hard floor. Make sure that air
circulation around the machine is not impeded by carpets,
rugs etc. Check that the machine does not touch the wall
or furniture. Level the washing machine by raising or
lowering the...

650-800 mm
The drain hose can be connected directly into the pipe
(e.g. beneath a washtub or sink), above the water trap. The
drain hose must be arranged so that some part of it’s
length is routed up to a level corresponding to the top
edge of the tub and fixed in place there.
Directly into a drain pipe at a height of not less than 65
cm and not more than 80 cm.
Their must be an air gap around and below the end of
drain hose. This means that the internal diameter of the
standpipe must be larger than the...

>PP