Zanussi Zbm 762 X Manual

							59
CLEANING AND MAINTENANCE
Replacing the Oven Light
¥ Ensure the electricity supply is switched off before
carrying out this operation.
The oven bulb has to comply to these features:
a) resistant to temperatures of 300 °C;
b) electric rate: 230 V - 50 Hz;
c) electric power rate: 25 W.;
d) connection type: E 14.
To replace the bulb, proceed as follows (Fig. 7):
a)push in and turn the glass lid anticlockwise;
b)remove tha faulty bulb;
c)replace it with a new one;
d)refit the glass lid;
e)switch on the electricity supply.
General Cleaning
¥ Before cleaning, always allow the oven to cool
down.
¥ When using spray cleaning products, be careful not
to spread them on the heating elements or on the
thermostat sensor.
¥ Never use harsh abrasives, steel wool or cleaners
with bleach, as they could damage the enamel and
the oven door glass.
The Oven Cavity
The enamelled oven cavity is best cleaned whilst the
oven is still warm. It is advisable to wipe the oven over
with a soft cloth soaked in warm soapy water after each
use. However, from time to time, it will be necessary to
do a more complete cleaning, using a proper oven
cleaner.
In case of particularly tough stains, you can use stainless
steel cleaning products or some warm vinegar.
¥If cooking fruits, some over-heated natual acids
can squeeze and settle on the oven enamel, causing
stains quite difficult to remove. This could affect the
enamel brightness, but it will have no consequence on
the oven performances. To avoid these stains to be
burnt out during the next cooking, carefully clean the
oven cavity after all fruits cookings.
The Oven Door and its gasket
Before cleaning the oven door, we recommend you to
remove it from the oven.
Proceed as follows:
a)open the oven door completely;
b)find the hinges linking the door to the oven (fig 5);
c)unlock and turn the small levers located on the two
hinges (fig. 5);
d)handle the door by its left- and right-hand sides, then
slowly turn it towards the oven until it is half-closed;
e)gently pull the oven door off its site (fig. 5);
f)place it on a steady plan;
g)unscrew the two screws marked with lett. A fig.6;
h)pull up the oven door glass and take it away from the
oven door.
Clean the oven door glass with warm water and a softh
cloth only.
Once the cleaning is carried out, refit the oven door,
following the procedure in reverse.
The correct operation of the oven is ensured by a gasket
placed round the edge of the oven cavity.
¥ Periodically check the condition of this gasket. If
necessary, clean it without using abrasive cleaning
products.
¥
If the gasket shows to be damaged, call you local
Zanussi Service Centre. Do not use the oven until it
has been repaired.
Fig. 7FO 0287
Fig. 5
Fig. 6FO 0288
FO 0027 
						

							60
FO 0781FO 0778
Allow the oven to cool down,
remove the drop collecting basin,
and unscrew the ring nuts of the
shelf supports.Remove the side panels.
If necessary, unscrew the fixing
screw of the back panel and remove
it. Once the cleaning is carried out,
refit the parts following these
instructions backwards.
FO 0145
FO 0085 FO 0028
Fig. 8Fig. 9
REMOVING THE  SELF-CLEANING
PANELS
If the self-cleaning panels have been installed into the
oven, they should be removed from time to time to
allow a thorough cleaning.
THE HINGED GRILL
This model has been fitted with a hinged grill element,
to enable you to clean the roof of the oven easily.
Before proceeding, ensure the oven is isolated from
the electricity supply. Then undo the screw which holds
the grill in place. (see Fig. 8)
Gently pull the grill downward to allow access to the
oven roof. (see Fig. 9).
Clean the oven roof with a suitable cleaner and wipe
dry before replacing the hinged grill element.
Gently push up the grill element into place and firmly
screw into place the holding nut.
NOTE: Ensure the grill holding nut is firmly in place
to avoid the grill falling down during operation. 
						

							61
   SOLUTION
uCheck the oven is in manual operation and that both a
cooking function and a temperature have been selected
   or
uCheck the appliance is wired in properly, and the socket
switch or the switch from the mains supply to the oven are
ON.
uTurn the thermostat knob on a temperature
   or
uTurn the oven function control knob on a function.
uTurn the oven function control knob on a function
   or
uBuy a new oven light bulb, asking for it to your local Zanussi
Service Centre and replace it by following the instruction
provided in this booklet.
uRefer to the contents of this booklet, especially to the
chapter Using the Oven.
uLeave dishes inside the oven no longer than 15-20 minutes
after the cooking is completed.
    SYMPTOM
nThe oven does not come on
nThe oven temperature light does not come on
nThe oven light does not come on
nIt takes too much time to finish the dishes, or they are
cooked too fast.
nSteam and condensation settle on the food and the
oven cavity.
If the appliance is not working correctly, please carry out the following checks, before contacting your local
Zanussi Service Centre.
WHAT HAPPENS IF SOMETHING GOES WRONG
If after the checks listed in the
previous chapter, the appliance
still does not work correctly,
contact your locals Zanussi
Service Centre, specifying the
type of malfunctioning, the
appliance model (Mod.), the
product number (Prod. No.) and
the serial number (Ser. No.)
marked on the identification plate.
This plate is placed on the front
external edge of the oven cavity.Original spareparts,
certified by the product
manufacturer and
carrying this symbol are
only available at our
Service Centre and
authorized spareparts
shops.
TECHNICAL ASSISTANCE AND SPARE PARTS
SER. NO.Mod.
PROD. NO.
SER. NO. MOD.
PROD. NO.TYPE 
						

							62
When calling for repairs during the period of guarantee ofthe
appliance, the original invoice or receipt must be shown or
sent together with the appliance to be repaired.
General conditions of guarantee
1The manufacturer guarantees the appliance indicated on
the relative invoice for a period of one year from the date
of purchase. In case of a fault during this period if caused
bya defect in materials and/or construction, the client is
entitled to repair free of charge.
1a Concerning vacuum cleaners for domestic use, the total
periodof guarantee is two years. Accessories are subject
to a direct usage, consequently these articles are excluded
from the guarantee.
2The manufacturer guarantees technical assistance and
repairsfor one year. Spare parts fitted during repair are
also covered by a one year guarantee from the date of
repair. In case of fault during this period, as a direct result
of the repair work carried out or caused by the new parts
fitted on such occasion, the client is entitled to repair free
of charge. The execution of repairs does not prolong the
total period of guarantee covering the appliance.
3Technical Assistance at domicile will be provided only for
large apparatus which are difficult to transport such as:
washing machines, spin-driers, dishwashers,refrigerators,
freezers (vertical or horizontal), ovens, cookers and built-in
appliances.
3aThe above-mentioned conditions are also valid for
refrigerators for caravens on condition that they are situated
within the national boundaries and are accessible by roads
open to traffic. Furthermore, at the time of the intervention
the appliance and its owner, or the person so authorized,
must be present at the place agreed upon for the
intervention.
4If, in the opinion of the manufacturer, the appliance as
described in point 3 must be transported to a Technical
Assistance laboratory, the transportation will be carried
out as established by the manufacturer, at his expense
and under his responsibility.
5All appliances not mentioned under points 3 and 3a,
includingappliances having the same functional
characteristics but whose transport is easy, must be sent
to the Technical Assistance or taken to them. Throughout
the period of guarantee the cost of return transportation
will be taken care by the manufacturer.
6If during the period of guarantee a disfunction occurs due
to a defect which cannot be repaired, the appliance will be
replaced free of charge.Extension of the guarantee
7For motorcompressors of refrigerators/ freezers (excluding
the starting device and thermal interrupter) a decreasing
guarantee of 20% per year for a period of five years from
the date of purchase of the appliance indicated on the
relative invoice with repairs free of charge throughout the
entire period under guarantee. On completion of the total
period of guarantee the cost of travel, workmanship and
eventual spare parts will be at the expense of the client.
Exclusion from guarantee
8The free execution of work for the repair and/ or substitution
as set out above will not apply if:
- The purchase invoice or receipt indicating the date of
purchase and the identification of the appliance cannot be
presented or was not sent with the appliance to be repaired;
- The appliance is used for purposes other than those of the
domestic nature for which it was made;
- The appliance was not installed, handled or used in
conformity with the indications in the instruction manual or
in the modalities for use;
- The appliance has been repaired or modified incorrectly
by unqualified personnel.
8aIf the appliance has been built-in, underinserted,
suspendedor installed in such a way that the time required
to move it and put it back in position exceeds thirty minutes
in total, the extra expenditures occurred will be billed to the
owner of the appliance.
8bln case of deterioration due to an irregular installation
carried out in agreement with the owner of the appliance,
the manufacturer and the technical assistance decline all
responsibility.
8c Damage such as scratches, knocks or breakage of movable
or dismountable units which were not notified to the
manufacturer at the time of delivery are not covered by the
guarantee.
Important notice
This appliance has been made to be safe. Inadequate repairs
can nonetheless compromise this safety. To avoid such
problems and to prevent any eventual damage we advise you
to have repairs carried out exclusively by qualified
personnel.We advise you to have repairs or maintenance
carried out by the retailer or the Elgroep Service and to request
only original spare parts.
GUARANTEE - SPARE PARTS (only for BENELUX)
Belgium
Electric Household Appliances
Bergensesteenweg 719
B - 1520  Halle (Lembeek)
Repairing to customers house:
Tel.:   02-3630444
Fax.:  02-3630400
Spare parts:
Tel.:   02-3630555
Fax.:  02-3630500
Telex:  22915 eluxbe 
						

							63
This appliance complies with the
following E.E.C. Directives:
- 73/23 - 90/683 (Low Voltage Directive);
- 89/336 
(Electromagnetical Compatibility
Directive);
- 93/68 (General Directives)
and subsequent modifications.
Height 59,4 cm
Width 56,0 cm
Depth 55,0 cm
Height 32,5 cm
Width 42,0 cm
Depth 39,0 cm
Volume  53     l
RECESS
DIMENSIONS
OVEN CAVITY
DIMENSIONS
TECHNICAL DATA
MANUFACTURER:
ELECTROLUX ZANUSSI
ELETTRODOMESTICI S.p.A.
Viale Bologna, 298
47100 FORLí (Italie)
Oven thermostat settings: from 50°C up to 250°C
Heating elements ratings
Bottom heating element 1000 W
Top heating element 800 W
Full Oven (Top+Bottom)(1000 + 800) 1800 W
Grill heating elements     simple 1750 W
         double 2550 W
Fan Oven heating element 2000 W
Oven lamp 25 W
Convection fan 30 W
Cooling fan 25 W
Maximum power rating (230V - 50Hz) 2600 W
Voltage tension (50 Hz) 230 V
FO 0414
TO THE ATTENTION OF THE INSTALLER
The following instructions are meant to a qualified
technician, in order to allow him carry out the
installation in compliance with the rules in force.
The building-in and the electrical connection fo the
appliance must be carried out by a qualified and
authorized technician only.
BUILDING IN
It is important that the dimensions and materials of the
surround or cabinet into which the oven will be built are
correct and will withstand a temperature increase.
A correct installation will have to ensure a proper
protection against contact with electric parts or merely
functionally isolated parts.
All the units meant to ensure protection have to be fitted
not to be taken away without using any tool.
We recommed not to install the appliance near
refrigerators or freezer, since the heat could affect the
performance of these appliances.
Oven dimensions (Fig. 10) 
						

							64 TERMINAL BLOCK
The oven has an easily accessible terminal block,
which is meant to work with an electric single-phase
rate of 230 V.
(Fig. 14)
The manufacturer disclaims any
responsability should all the safety
measures not be carried out.
ELECTRICAL CONNECTION
Before the appliance is connected:
1) check that the main fuse and the domestic installation
can support the load;
2) check that the power supply is properly earthed in
compliance with the current rules;
3) check the socket or the double pole switch used for
the electrical connection can be easily reached with
the appliance built in the forniture unit.
This appliance is supplied with a type H05 RR-F
connection cable, section 3 x 1,5 mm
2. A suitable
plug, able to carry the load specified on the rating
plate, must be fitted to the cable. This is a three-wired
cable, with the earth wire marked yellow-green.
The plug has to be fitted in a proper socket.
If connecting the appliance directly to the electric system,
a double pole switch must be installed between the
appliance and the electricity supply, with a minimum
gap of 3 mm. between the switch contacts and of a type
suitable for the required load in compliance with the
current rules. The earth wire must not be interrupted by
the double switch pole.
The connection cable has to be placed in order that, in
each part, it cannot reach a temperature 50 °C higher
than the room temperature.
After the connection is carried out, test the heating
elements for about 3 minutes.Undertop Recess Dimensions (Fig. 12)
FO 2159Fig. 14
FO 0039Fig. 13
SECURING THE OVEN TO THE CABINET
Fit the appliance into the cabinet recess.
Open teh oven door and secure the oven to the kitchen
cabinet with four wood screws, which fit the holes
provided in the oven frame (Fig.13).
When installing an electric plate hob over the oven, the
hobs electrical connection and the ovens one have to
be carried out separately, for security reasons and to let
the oven be taken off the unit easier, if necessary.
In-Column Recess Dimensions (Fig. 11)
FO 0290
FO 2154