Zanussi Zdf 2020 User Manual

							• The end indicator light comes on.
For better drying results, keep the door ajar for some mi-
nutes before you remove the dishes.
Let the dishes cool down before you remove them from
the appliance. Hot dishes are easily damaged.
Removing the load
• First remove items from the lower basket, then from
the upper basket.
• There can be water on the sides and door of the appli-
ance. Stainless steel becomes cool more quickly than
the dishes.
Care and cleaning
Warning!  Switch the appliance off before you clean
the filters.
Cleaning the filters
Important!  Do not use the appliance without the filters.
Make sure that the installation of the filters is correct.
Incorrect installation will cause unsatisfactory washing
results and damage to the appliance.
12
Fully clean the filters A, B
and C below running wa-
ter.
3
To remove filters B and C,
turn the handle approxi-
mately 1/4 anticlockwise.
4
Remove the flat filter A
from the bottom of the ap-
pliance.
5
Put the flat filter A in the
bottom of the appliance.
Install the flat filter cor-
rectly under the two
guides D.
6
Put the filter system in po-
sition. To lock the filter
system, turn the handle
clockwise until it locks in
position.
Important!  Do not remove the spray arms.
If the holes in the spray arms become clogged, remove
remaining parts of soil with a cocktail stick.
External cleaning
Clean the external surfaces of the appliance and control
panel with a damp soft cloth. Only use neutral detergents.
Do not use abrasive products, scouring pads or solvents
(acetone, trichloroethylene etc...).
Frost precautions
Caution!  Do not install the appliance where the
temperature is below 0 °C. The manufacturer is not
responsible for damage because of frost.
If not possible, empty the appliance and close the door.
Disconnect the water inlet hose and remove water from
the water inlet hose.
 11
 
						

							What to do if…
The appliance does not start or stops during operation.
If there is a fault, first try to find a solution to the problem
yourself. If you cannot find a solution to the problem
yourself, contact the Service Force Centre.Caution!  Switch off the appliance before you do the
below suggested corrective actions.
Fault code and malfunctionPossible cause and solution
• continuous flash of the start/cancel in-
dicator light
• 1 flash of the end indicator light
The dishwasher does not fill with water• The water tap is blocked or furred with limescale.
Clean the water tap.
• The water tap is closed.
Open the water tap.
• The filter in the water inlet hose is blocked.
Clean the filter.
• The connection of the water inlet hose is not correct. The hose can
be kinked or squashed.
Make sure that the connection is correct.
• continuous flash of the start/cancel in-
dicator light
• 2 flashes of the end indicator light
The dishwasher will not drain• There is a blockage in the sink spigot.
Clean the sink spigot.
• The connection of the water drain hose is not correct. The hose can
be kinked or squashed.
Make sure that the connection is correct.
• continuous flash of the start/cancel in-
dicator light
• 3 flashes of the end indicator light
The anti-flood device operates• Close the water tap and contact your local Service Force Centre.
The programme does not start• The appliance door is not closed.
Close the door.
• Mains plug is not connected in.
Put in the mains.
• The fuse has blown out in the household fuse box.
Replace the fuse.
• Delay start is set.
Cancel the delay start to start the programme immediately.
After the check, switch on the appliance. The programme
continues from the point of interruption. If the malfunction
shows again, contact your Service Force Centre.
These data are necessary to help you quickly and cor-
rectly:
• Model (Mod.)
• Product number (PNC)• Serial number (S.N.)
For these data, refer to the rating plate.
Write the necessary data here:
Model description : ..........
Product number : ..........
Serial number : ..........
12
 
 
						

							The cleaning results are not satisfactory
The dishes are not clean• The selected washing programme is not applicable for the type of load and
soil.
• The baskets are loaded incorrectly so that water cannot reach all surfaces.
• Spray arms do not turn freely because of incorrect arrangement of the load.
• The filters are dirty or not correctly installed.
• The quantity of detergent is too little or missing.
Limescales particles on the dishes• The salt container is empty.
• The water softener is adjusted on a wrong level.
• The salt container cap is not closed correctly.
The dishes are wet and dull• No rinse aid has been used.
• The rinse aid dispenser is empty.
There are streaks, milky spots or
a bluish coating on glasses and
dishes• Decrease the rinse aid dosage.
Dry water drop signs on glasses
and dishes• Increase rinse aid dosage.
• The detergent can be the cause.
Technical data
DimensionsWidth cm60
 Height cm85
 Depth cm61
Electrical connection - Voltage -
Overall power - FuseInformation on the electrical connection is given on the rating plate on the
inner edge of the dishwasher door.
Water supply pressureMinimum0,5 bar (0,05 MPa)
 Maximum8 bar (0,8 MPa)
CapacityPlace settings12
Environment concerns
The symbol    on the product or on its packaging
indicates that this product may not be treated as
household waste. Instead it should be taken to the
appropriate collection point for the recycling of electrical
and electronic equipment. By ensuring this product is
disposed of correctly, you will help prevent potential
negative consequences for the environment and human
health, which could otherwise be caused by inappropriate
waste handling of this product. For more detailedinformation about recycling of this product, please
contact your local council, your household waste disposal
service or the shop where you purchased the product.
The packaging materials are environmentally friendly and
can be recycled. The plastic components are identified by
markings, e.g. >PEPS
						

							Warning!  To discard the appliance, follow the
procedure:
• Pull the mains plug out of the socket.
• Cut off the mains cable and mains plug and discard
them.• Discard the door catch. This prevents the children to
close themselves inside the appliance and endanger
their lives.
Installation
Warning!  Make sure that mains plug is
disconnected from the mains socket during
installation.
Fitting under a counter
Put the appliance adjacent to a water tap and a water drain.
Remove the appliance worktop to install it under a sink
unit or a kitchen worktop. Make sure that the dimensions
of the recess agree with the given dimensions.
12
34
Install the appliance worktop to the appliance if you want
to use the dishwasher as a freestanding appliance.
The plinth on freestanding appliance is not adjustable.
Adjusting the level of the appliance
Make sure that the appliance is level to close and seal the
door correctly. If the level of the appliance is correct, the
door does not catch on the sides of the cabinet. If the door
does not close correctly, loosen or tighten the adjustable
feet until the appliance is level.
Water connection
Water inlet hose
Connected the appliance to a cold water supply.
Connect the inlet hose to a water tap with an external
thread of 3/4”.
Caution!  Do not use connection hoses from an old
appliance.
The water pressure must be in the limits (refer to the
chapter Technical data). Make sure that the local water
authority gives you the average mains pressure in your
area.
Make sure that there are no kinks in the water inlet hose
and that the water inlet hose is not squashed or entangled.
Turn the inlet hose to the left or the right to suit the in-
stallation. Fit the locknut correctly to prevent water leaks.
Caution!  Do not connect the appliance to new pipes
or pipes that are not used for a long time. Let the
water run for some minutes, then connect the inlet hose.
Drain hose
1
Connect the water drain
hose to the sink spigot.
max 85 cm
min 40 cm
max 400 cm
2
14
 
 
						

							34
The internal diameter must not be smaller than the diam-
eter of the hose.
If you connect the water drain hose to a trap spigot under
the sink, remove the plastic membrane (A). If you do not
remove the membrane, remaining food can cause a block-
age in the drain hose spigot.
Caution!  Make sure that the water couplings are
tight to prevent water leakage.
Electrical connection
Warning!  The manufacturer is not responsible if
you do not follow these safety precautions.
Ground the appliance according to safety precautions.
Make sure that the rated voltage and type of power on the
rating plate agree with the voltage and the power of the
local power supply.
Always use a correctly installed shockproof socket.
Do not use multi-way plugs, connectors and extension
cables. There is a risk of fire.
Do not replace the mains cable yourself. Contact the
Service Force Centre.Make sure that the mains plug is accessible after
installation.
Do not pull the mains cable to disconnect the appliance.
Always pull the mains plug.
Warning!  The appliance is supplied with a 13 amp
plug attached. Use a 13 amp ASTA approved (BS
1362) fuse if it is necessary to change the fuse in the plug
supplied.
 15
 
						

							To buy accessories, consumables and spare parts at our online shop please visit:
www.zanussi.co.uk
www.zanussi.com
156985810-00-052009