Land Rover 90 110 Workshop Rover Manual
Here you can view all the pages of manual Land Rover 90 110 Workshop Rover Manual. The Land Rover manuals for Automobile are available online for free. You can easily download all the documents as PDF.
Page 2
TABLE OF CONTENTS SECTION Introduction mI ........................................................................\ .............................. ........................................................................\ ........... El General Specification Data .......................... Engine Tuning Data.. .I!. ............................................................. ........................................................................\ ............. Torque Wrench Settings.. mb...
Page 3
BOOK ONE CONTENTS 05 Page ENGINE TUNING DATA Section Number ri -Repairs and replacement parts - Poisonous substances -Fuel handling precautions -Fuel tank draining and repair J .. - - Service tools 5 - Location of vehicle identification numbers 6 06 TORQUE WRENCH SETINGS El GENERAL SPECIFICATION DATA - V8 engine data -2.25 litre petrol engine data -2.25 litre petrol engine data - 2.25 litre dicscl cnginc data -2.50 litre dicsel engine data - General data - all models...
Page 4
Book One Contents (cont’d) 07 Section GENERAL FITTING INSTRUCTIONS -Precautions against damage -Safety precautions -Preparation and dismantling -Inspection of components -Ball and roller bearings - Oil seals -Joints and joint faces - Flexible hydraulic pipes and hoses - Metric bolt identification - Metric nut identification - Hydraulic fittings - Keys and keyways -Tab washers, split pins, nuts and locking wire - Screw threads - Unified thread identification 1091...
Page 5
01 fi;y :i: INTRODUCTION ... ,:.; :.? , ... ..:I. .!I, I . ._ ...,., , . ... This Workshop Manual covers the Land Rover Ninety and One Ten range of vehicles. It is primarily designed to assist skilled technicians in the efficient repair and maintenance of Land Rover vehicles. Using the appropriate service tools and carrying out the procedures as detailed will enable the operations to be completed within the time stated in the Repair Operation Times. The Manual has been...
Page 6
lo1 I Always have a fire extinguisher containing FOAM CO? GAS, or POWDER close at hand when handling or draining 0 fuel, or when dismantling fuel systems and in areas whcre fuel containers are stored. Always disconnect the vehicle battery BEFORE carrying out dismantling or draining work on a fuel system. Whenever petroVgasoline is being handled, drained or stored, or when fuel systems are being dismantled all forms of ignition must be extinguished or removed, any...
Page 7
- Special Service Tools The use of approved special service tools is important. They are essential if service operations are to be carried out efficiently, and safely. The amount of time which they save can be considerable. Every special tool is designed with the close co -operation of Land Rover Ltd., and no tool is put into production which has not been tested and approved by us. New tools are only introduced where an operation cannot be satisfactorily carried out...
Page 8
LOCATION OF VEHICLE IDENTIFICATION AND UNIT NUMBERS VEHICLE IDENTIFICATION NUMBER (VIN) The Vehicle Identification Number and the recommended maximum vehicle weights are stamped on a plate riveted to the top of the brake pedal box in the engine compartment. The number is also stamped on the right -hand side of the chassis forward of the spring mounting turret. Always quote this number when writing to Land Rover Limited. Key to Vehicle Identification Number Plate...
Page 9
LOCATION OF VEHICLE IDENTIFICATION AND UNIT NUMBERS ST663M 01 FRONT AXLE Stamped on top of the left-hand axle tube. REAR AXLE Stamped on rear of left-hand axle tube. MAIN GEARBOX LT77 - 4 CYLINDER VEHICLES Stamped on a pad on the right-hand side of the gearbox immediately below the oil filler level plug. U ST665M TRANSFER GEARBOX LT230R - 4 CYLINDER VEHICLES Stamped on the casing on the left-hand side of the gearbox below the mainshaft rear bearing housing...
Page 10
GENERAL SPECIFICATION DATA ENGINE Type ................................................................. Number of cylinders ............................................. Bore ................................................................. Stroke ............................................................... Capacity ............................................................ Valve operation.. ................................................. Maximum power- B.H.P...