3D Perception CompactView Sx25+e User Manual

3D perception             COMPACTVIEW SX25+ 
Revision 3                    User Manual   
 
  16 
 
 
12.  GCM - GEOMETRY CORRECTION MODULE 
The GCM (Geometry Correction Module) facilitates, v
ia CompactDesigner/CompactControl, the 
special features unique to the 3D perception projec tion solutions. These include: 
 
· Image warping 
·  Soft edge blending 
·  Colour balance and matching 
·  Masks 
  
For full details on achieving the effects of these  features please read the...

3D perception             COMPACTVIEW SX25+ 
Revision 3                    User Manual   
 
  17 
 
 
 
 
12.2  Connecting the CompactView SX25+E 
The CompactView SX25+E must be connected to a chann el in a CompactUTM. For full details 
please see the CompactUTM  basic/CompactUTM zer0 Us er Manual. 
        

3D perception             COMPACTVIEW SX25+ 
Revision 3                    User Manual   
 
  18 
 
 
13.  FOCUS AND ZOOM 
13.1  Focus 
Turn the Focus ring (A) on the projection lens  
to get a correctly focused image.  
 
 
13.2  Zoom 
Turn the Zoom ring (B) on the projection lens  
to zoom In and Out. (This is only available on  
the optional zoom lens.)    
 If the desired image size cannot be achieved  
by adjusting the zoom ring, relocate the 
projector nearer or farther away from the 
projection...

3D perception             COMPACTVIEW SX25+ 
Revision 3                    User Manual   
 
  19 
 
 
14.  MOUNTING THE PROJECTOR 
14.1  To a Ceiling Mount 
The projector can be ceiling mounted using any appr
oved UL tested/listed ceiling mount fixture 
with a minimum weight capacity of 12 kg (26 lbs).    
The ceiling mount obtainable through 3D perception  (as illustrated below) is only approved for 
C
OMPACTVIEW projectors. 
  
For the ceiling mount use M4 screws provided.    
For proper ventilation,...

3D perception             COMPACTVIEW SX25+ 
Revision 3                    User Manual   
 
  20 
 
 
14.2  To a Tabletop 
The projector may be mounted or sited directly onto
 a tabletop. 
  
To  adjust  the  projected  image  to  the  desired  height   on  the  screen,  eject  the  front  foot  (C)  by 
pressing the release button (D), and adjust the ang le to the right position. 
  
To get an image level with the screen, turn the rea r feet (E) to the right position. 
 
 
 
NOTE:  Although this method...

3D perception             COMPACTVIEW SX25+ 
Revision 3                    User Manual   
 
  21 
 
 
15.  USING THE PROJECTOR 
After set-up, switch on all equipment.    
To switch the projector on, firmly press the POWER 
button on the keypad or the remote control. 
The STATUS indicator will turn from yellow to green  when the projector is switched on. 
 
When only one source is connected, the projector wi ll auto-detect the source. If more sources 
are connected, the projector will display the sourc e...

3D perception             COMPACTVIEW SX25+ 
Revision 3                    User Manual   
 
  22 
 
 
16.  MENU SYSTEM 
The menu system gives access to a multitude of imag
e and system controls. 
  
The menu system is structured through a top menu wi th several sub menus. The sub menus will 
vary depending on the actual source selected.   
Top Menu   
picture:   
Basic picture controls    
dynamic: 
Allows additional control over the  
projected image. 
  
advanced:   
Advanced picture controls   
setup:...

3D perception             COMPACTVIEW SX25+ 
Revision 3                    User Manual   
 
  23 
 
 
16.1  Picture Sub-menu 
S-VIDEO/COMPOSITE VIDEO 
 
  
VGA 
 
DVI 
 
YPbPr (progressive) 
 
brightness  
Adjusts the image brightness. A higher setting will  
increase the brightness a lower setting will decrea se 
the brightness of the image.    
contrast  
Controls the contrast of the image. A higher settin g 
will yield a harder image with larger difference  
between shades, while a low setting will...

3D perception             COMPACTVIEW SX25+ 
Revision 3                    User Manual   
 
  24 
 
 
16.2  Dynamic Sub-menu 
FOR ALL 
 
 
white boost  
Increases the white level of the image for enhanced  
contrast   
gamma  
The source image is adapted to characteristics typi cal 
to certain applications. This enables an optimized 
display of images, depending on whether the source  
is video, computer etc.   
eco mode  
Reducing lamp power for maximum lamp life and 
reduced power consumption   
lamp...

3D perception             COMPACTVIEW SX25+ 
Revision 3                    User Manual   
 
  25 
 
 
16.3  Advanced Sub-menu 
S-VIDEO/COMPOSITE VIDEO 
 
  
VGA 
 
  
DVI 
 
YPbPr (progressive) 
 
 
h position  
Shifts the image sideways.    
v position  
Shifts the image up and down.    
phase 
Adjust for stable image. A jittery image may appear  
with certain VGA sources. You may also press the  
AUTO button on the keypad or remote control to  
optimize.   
frequency  
Adjust image width. An incorrect...