Accel FX22 Command Center Switcher Looper Pedal Board User Manual

          
              
             
                   
SWITCHER / LOOPER   PEDAL BOARD 
 
Features: 
- Easy Setup 
- Clean cable routing 
- Rugged Lightweight Aluminum Design 
- Accel Power Supply Mounting Holes 
- Universal Power Supply Mounting Bracket for other  
  manufacturer’s  Power Supplies (Sold Separately) 
- Universal Power Supply Mounting with 3M Dual Lock.  
- Links to other Modular XTA series Accel Pedal Boards. 
- Dimensions:  
  22.00” (56cm) L x 14.50” (37cm) W x 2.90” (7.37cm) H 
-...

2 
 
Contents 
Introduction, Pedal Board Setup (Power Supply Mounting, Hookand Loop & 3M Dual lock Mounting, Cable Routing) ..... 3-5 
Switcher Looper Set up: .......................................................................................................................................................... 5 
Switcher Looper Functionality Overview,   .............................................................................................................................. 5 
(1) BANK DN...

3 
 
 
Introduction  
 
The Accel FX22 Command Center Switcher combines two great products together for a clean and easy to setup pedal 
board. This pedal board is primarily designed to switch multiple guitar effects pedals at the same time along with some 
amp switching functions using a single footswitch. Different combinations of effects pedals and different switchable amp 
settings can be stored on different patches allowing the player to easily change between multiple effects loops and 
switchable...

4 
 
 
Universal Power Supply mounting method “B”.  
(Universal mounting bracket and 6-32 hardware sold separately)   
 
  
 
Step 2: Attach adhesive backed Hook and Loop and 3M Dual Lock Strips: 
(If you mounted your power supply using hardware, be sure you leave open area around the screw heads in case you 
need to remove your power supply in the future!)  
 
We recommend alternating your strips of hook and loop and 3M Dual lock strips as shown in fig. 1 below.  
 
If you are thinking about using two...

5 
 
 
 
 
 
Step 3: Cable Path feed through examples directly down to Switcher Looper. 
 
 
  
 
 
Switcher Looper Set up: 
1) Connect the effects pedals to the Accel programmable switch as shown under one of the “Typical 
Configuration Drawings” in this user’s manual, (pages 12 and 13). Make sure to use a 9V input at least 350mA.    
2) Reference the “Over View section (pages 5 – 7) for component and feature identification. 
3) Power up switcher.  
     
For this unit to function properly use only a 9V...

6 
 
 
                  
(1)  BANK DN      
BANK DOWN switch 1(SW1);  
In “Recall Mode”, press this switch to decrease the bank number.  
In “Program Mode”, hit this switch to shift the programming between loop1~4 (“L” in LCD Display ) and loop5~8 (“H” 
in LCD Display). 
To toggle between “ Recall Mode” and “Program Mode” hold this switch down for a couple seconds. Check for more 
details in the “Programming Loops and Foot switches” section (page 4). 
 
(2) BANK UP 
BANK UP switch (SW2); 
In “Recall...

7 
 
(10) TUNER 
Connects to tuner. 
 
(11) SEND & RETURN 1-7 
Loop pairs, connects SEND (S*) to guitar pedal input, RETURN(R*) to guitar pedal output. 
 
(12) OUTPUT 
OUTPUT jack of the switcher, the input signal reaches this jack via loop1~7. 
 
(13) DC Jack 
5.5 x 2.1 mm type, use negative center DC 9V / 350 - 500mA power supply (this unit will not function properly under 
350mA’s).  
 
(14) LOOP8 
Loop8 is a separate loop, FX LOOP IN8 is the input of this loop, SEND8 sends the signal and RTN8 returns...

8 
 
Primary Functions: 
 
 
  
   

9 
 
Secondary Functions: 
  

10 
 
Restoring Factory Presets: 
 
 
 
 
Specifications 
Dimensions ......................................................................................... 480(L) x60(W)X52(H) mm 
Weight ............................................................................................................................... 1000g 
Power Supply ....................................................................................... DC9V (Negative Center) 
Current Drain...