Accel FX8 Command Center Switcher Looper User Manual

							11 
 
 
 
  
 
  
						

							12 
 
Glossary 
Active Bank Set Up Mode (ABS): Defines a chosen range of banks. The full range is  1 -10, the number “0” 
being 10. You can narrow this range through the utilizing the ABS function. (See page 5)  
Active Bank Pool Setup (BPS): Defines “Bank Pool” to be used (red or green). Red bank pool consists of 10 
banks and Green bank pool consists of 10 banks.  (See page 5) “Active Bank Pool Setup (BPS)”.     
Bank: A bank holds 4 preprogrammed “preset A/B/C/D switches” in each bank. You have a total of 10 banks 
accessible when in recall mode. Your choice of either 10 red or 10 Red with a dot. (Red without a dot is the 
factory default set of banks).  
(BANK DN) (BANK UP): Cycles up or down through banks.   
BANK POOL: A defined set of red (with and without a dot). (Red bank pool without a dot, is the factory set 
default).  (See page 5) “Active Bank Pool Setup (BPS)”. 
 Loops: In reference to a pedal being inserted (looped) into the signal path. Via the Send (S*) and Return (R*) 
jacks on the back side of the unit. After programming the loops in, they are recalled by using the 4 
preprogrammed “preset A/B/C/D switches” that are relative to the bank being used. 
Bypass: The signal bypasses the switcher. After any preset switch A,B,C or D has been activated (signaled by 
a lit solid red LED above the switch) Press the same switch again. You will see a solid blue LED above the 
“BANK UP” (Bypass) switch. You will then be in bypass mode.   
_______________________________________________________________________________                
Modes: 
Program Mode:   
Primary Programming Functions; These text are shown with Black text in a white background.   
They are relative to the programming of Loops , Banks, Foot Switches. Also Programs Active Bank Setup Mode 
“ABS” to define only the number of banks you wish to use. (See Page 5) 
Less Used Programming Functions: These text are shown in parenthesis (   ).  
These are relative to the programming of Active Bank Pool Setup (BPS), if you wish to define Bank Pools (Red 
with or witout a dot) for use. You can only use one at a time (page 5). Also Factory Reset (Reset). (page 6) 
Recall Mode: (W hite text on unit refers to Recall Mode functions) 
Recall Mode: Recalls Loops , Banks, Foot Switches,  that have been programmed in. 
Recall Mode Functions: 
_______________________________________________________________________________________ 
 
Programmable Switches:     
(SW1 PGM) “Switch1 Program Mode” 
(SW2 PGM) “Switch2 Program Mode” 
 
Presets :  In reference your  switches A, B, C, or D that have been preset through process of  programming 
your loops. Often referred to preset switches.  
 
 
 
Warranty 
Limited 1 Year Warranty 
This warranty covers any defects or malfunctions in your new Accel Power Source 8 Power Supply. This a 1 year 
warranty for the original registered purchaser.  Accel will fix or replace any defective units with the first 1 years from the 
purchase date. Fixing or replacing the unit will be at Accels discretion. Any problem that is caused by abuse, misuse, or 
an act of God (such as a flood) are not covered. In order to be eligible for service under this warranty you must return the 
warranty registration card attached below within 30 days of purchasing the aid.  
If something goes wrong with your Accel Power Source 8 Power Supply, send it postage paid with a brief written 
description of the problem to:  
Accel Technologies LLC;. 
5505 East Santa Ana Canyon Rd. 
#17057 
Anaheim, CA 92817 
This warranty gives you specific legal rights, and you may also have other rights which vary from state to state.  
 
Accel Technologies, LLC. 
P.O. BOX 17057 Anaheim, CA 92817 U.S.A. 
Email: [email protected]