Acco Nobo Projector S11E DLP User Manual

11 INSTALLATION
POWERING ON THE PROJECTOR
Remove the lens cap.
Ensure that the power cord and signal cables are securely
connected.
Turn on the lamp by pressing “Power/Standby” button on the
control panel. The startup screen will be displayed for 20 seconds
and the Power/Standby indicator will light solid green.
Turn on the source (computer, notebook, or video player, etc.) The
projector will detect your source automatically.
•If the projector displays “No Signal,” please make sure the      
signal...

12 INSTALLATION
POWERING OFF THE PROJECTOR
Press the “Power/Standby” button to turn off the projector lamp. The projector will
display the message “Power off the lamp?”
Press the “Power/Standby” button again to confirm. Otherwise the message will
disappear after 5 seconds.
“Power/Standby” indicator will turn green for approximatly 90 seconds. When the
green light begins flashing, the projector has entered standby mode.
If you wish to turn the projector back on, you must wait until the projector has...

The projector is equipped with an elevator foot for adjusting the projector
height.
To raise the projector
To lower the projector
13 INSTALLATION
ADJUSTING THE PROJECTOR HEIGHT
Press the Elevator Button.
Raise the projector to the desired display angle, then release the button 
to lock the elevator foot into position.
Use the Height Adjuster Button to fine-tune height adjustment.1
Press the Elevator Button.
Lower the projector, then release the button to lock the elevator foot into
position.
Use the...

14 INSTALLATION
To adjust the focus, simply rotate the focus ring until the image is clear. The
projector will focus at distances from 4.0 feet to 39.4 feet (1.2m to 12m)
ADJUSTING THE PROJECTOR FOCUS
ADJUSTING THE PROJECTOR IMAGE SIZE
Focus Ring
This graph is for 
User’s reference only
289.7”
237.5”
185.3”
133.8”
81.6”
29.4”
(4)
(11.1)
(18.2)
(25.2)
(32.3)
(39.4)
Screen
(Diagonal)29.4”81.6”133.8”185.3”237.5”289.7”
Screen 
Size (WxH)23.5 x 17.7”65.3 x 48.9”107.1 x 80.3”148.2 x 111.2”190.0 x 142.5”231.8 x...

15 USER CONTROLS
There are two ways for you to control the functions: Remote
Control or Panel Control.
PANEL CONTROL & REMOTE CONTROL
Remote Control
Panel Control
Power / Standby
■Refer to the Power On / Off the Projectorsection on page 11. 
Optimum Setting
■PressOptimumto select Conference Mode or Cinema Mode.
Source
■PressSourceto cycle between VGA, S-Video, Composite, 
and Component sources
1. Power Indicator Light
2. Power / Standby
3. Re-sync
4. Menu/On/Off/Enter5. Four Directional Select Keys
6....

16 USER CONTROLS
Multi-Directional Selector
■These keys are used to control the direction  operation on the OSD display.
Page Up (Computer Mode only)
■Use this button to page up. This function is only available when the projector is connected 
to a computer via a USB cable.
Page Down (Computer mode only) 
■Use this button to page down. This function is only available when the projector is 
connected to a computer via a USB cable.
Menu
■Press “Menu” to open the OSD menu and press   key to select menu...

17 USER CONTROLS
ON-SCREEN DISPLAY MENUS
How to Operate
■The projector has multilingual OSD menus that allow you to make image
adjustments and change a variety of settings. With a computer source, the OSD
displayed is the “Computer OSD”. With a video source, the OSD display is the
“Video OSD” The projector will automatically detect the source.
■To open the OSD menu, press the “Menu” button on the remote control or 
panel control.
■When the OSD is displayed, press   key to select main items.
E.g.: Image-I...

18 USER CONTROLS
Computer Mode
IMAGE-I
(COMPUTER MODE)
Brightness
Adjusting the brightness of the image. 
■Press the       key to darken the image.
■Press the       key to lighten the image.
Contrast
The contrast controls the degree of difference between the lightest and
darkest parts of the picture. Adjusting the contrast changes the amount of
black and white in the image.
■Press the       key to decrease the contrast.
■Press the       key to increase the contrast.
Colour Temperature
Adjust the colour...

19 USER CONTROLS
Video Mode
IMAGE-I
(VIDEO MODE)
Brightness
Adjusting the brightness of the image. 
■Press the key to darken the image.
■Press the key to lighten the image.
Contrast
The contrast controls the degree of difference between the lightest and
darkest parts of the picture. Adjusting the contrast changes the amount of
black and white in the image.
■Press the key to decrease the contrast.
■Press the key to  increase the contrast.
Colour
The colour setting adjusts a video image from black and...

20 USER CONTROLS
Computer Mode
IMAGE-II
(COMPUTER MODE)
Frequency
“Frequency” is for changing the display data frequency to match the
frequency of your computer’s graphic card. When you experience a vertical
flickering bar, use this function to make an adjustment.
Tracking
Choose “Tracking” item to synchronise the signal timing of the display with
that of the graphic card. When you experience an unstable or flickering
image, use this function to correct it.
Aspect Ratio
You can use this function to fit...