Adam Equipment GK Indicator GKREVL1 User Manual

 © Adam E\buipm\fnt Company 2013
Adam Eq\bipme\ft 
GK INDICATOR 
(P.N. 305669264, Revision L1, August  2013) 
V1.21  GK-H  scales for E\brope 
V2.29 EC Approved scale 
V3.41  GK scale for E\brope  V4.12  GK-H scale for USA V5.41  GK  scales for USA   

 © Adam Equipment Company 2013 
     
    Easy Reference:  
    
Model name of the indicator: 
 
 
Serial number of the unit: 
 
 
Software revision number  
(Displayed when power is first turned on): 
 
Date of Purchase: 
 
 
Name of the supplier and place: 
 
 
          

 © Adam Equipment Company 2013 1 
CONTENTS 
 
1. INTRODUCTION ....................................... .............................................. 3 
2. SPECIFICATIONS ..................................... ............................................. 5 
3. INSTALLATION ...................................................................................... 7 
3.1. UNPACKING ..................................................................................... 7 
4....

 © Adam Equipment Company 2013 2 
16.2. USING “2006” TO ENTER THE SERVICE PARAMETERS ....... . 53 
16.2.1 F1 -CALIBRATION ................................................................. 55 
16.2.2 F2–DECIMAL POINT POSITION.......................... .................. 56 
16.2.3 F3 – CAPACITY ..................................................................... 56 
16.2.4 F4 –INITIAL ZERO RANGE............................. ....................... 57 
16.2.5 F5 -RE-ZERO RANGE...

 © Adam Equipment Company 2013 3 
INTRODUCTION 
 
·  The  GK  indicator  provides  an  accurate,  fast  and  versatile   general 
purpose  indicator  with  parts  counting,  percent  weig hing  and  check-
weighing functions.  
 
·  The   GK   has  LEDs  to  indicate  when  a  weight  is  below  the  lo w  limit, 
between  the  limits  or  above  the  high  limit  next  to  the  display.    These 
can  work  in  conjunction  with  an  audible  alarm  for  c heck  weighing  as 
well as LCD showing LO, OK...

 © Adam Equipment Company 2013 4 
  

 © Adam Equipment Company 2013 5 
SPECIFICATIONS 
INPUT SECTION 
Load Cells  Up to 4 , 350 ohm load cells 
Minimum 87 ohms, maximum 1120 ohms 
Connection  6 wires 2 excitation, 2 sense, 2 signal 
Excitation  5Vdc 
Sensitivity  0.15uv/d    (GK-M, 1.5uv/e) 
Linearity  0.01% FS 
Zero Range   0- 10mv 
Signal range  0-40mv 
ADC Sensitivity  Approximately  0.02 µv/ADC count 
DIGITAL SECTION 
Maximum Range  Typically 1kg – 30000kg 
Divisions  Up to 30,000, (GK –M, 3000 or less) 
Weigh units  kg / g / lb for...

 © Adam Equipment Company 2013 6  

 © Adam Equipment Company 2013 7 
INSTALLATION 
1.1.  UNPACKING  
This indicator must be connected to a load cell pla tform and calibrated as necessary 
to  match  the  platform  and  user  requirements.    See  S ection  15  for  set-up 
information.  
The users application and the technical specificati ons of the platform or load cell will 
determine the necessary configuration.   
LOCATING  
 
   
 
   
 
 
 
 
 
·  The  scales  should  not  be  placed  in  a  location  that  will 
reduce the...

 
8                              © Adam Equipment Company 2013 
CONNECTION  
This indicator must be connected to a load cell pla tform and calibrated as necessary 
to match the platform and user requirements.    
The  GK  has  a  connector  configured  for  a  6  wire  load   cell.        Connect  the  load 
cells/platform to the indicator as shown below.  Th e cable length should be as short 
as possible, using a large size wire to minimise er rors due to resistance in the leads.   
 
GK-M model must...