Home
>
Addonics Technologies
>
HDD Duplicator
>
Addonics Technologies 11 Hard DriveSSD Duplicators HDUS325DX User Manual
Addonics Technologies 11 Hard DriveSSD Duplicators HDUS325DX User Manual
View the Addonics Technologies 11 Hard DriveSSD Duplicators HDUS325DX User Manual for free. All the Addonics Technologies manuals and user’s guides are available for free view without any registration. You can also download the manual as PDF to your computer.
![Page 2
www.addonics.comTechnical Support (M-F 8:30am - 6:00pm PST) Phone: 408-453-6212 Email: www.addonics.com/support/query/
Drive Installation
The top enclosure houses the SOURCE drive and the bottom enclosure
houses the TARGET drive.
To install drives, unlock the enclosure using the provided key and gently\
pull
the lever until the door swings open.
For 3.5” installation, insert the drive with the SATA connectors to the rear and
the label side up as shown. For 2.5” drives, follow the steps below t\
o...](http://img.usermanuals.tech/thumb/181/2449/w300_11-hard-drivessd-duplicators-hdus325dx-1478566081_d-1.png "Page 2
www.addonics.comTechnical Support (M-F 8:30am - 6:00pm PST) Phone: 408-453-6212 Email: www.addonics.com/support/query/
Drive Installation
The top enclosure houses the SOURCE drive and the bottom enclosure
houses the TARGET drive.
To install drives, unlock the enclosure using the provided key and gently\
pull
the lever until the door swings open.
For 3.5” installation, insert the drive with the SATA connectors to the rear and
the label side up as shown. For 2.5” drives, follow the steps below t\
o...")
![Page 3
www.addonics.comTechnical Support (M-F 8:30am - 6:00pm PST) Phone: 408-453-6212 Email: www.addonics.com/support/query/
To install a 2.5” drive into the Snap-In 25 adapter:
Step 1. Gently squeeze the latches on the Snap-In 25 tray and slide it out of
the enclosure.
Step 2. Gently pull the drive retainer clips outward on the tray while inserting\
the drive from the top.
Latches](http://img.usermanuals.tech/thumb/181/2449/w300_11-hard-drivessd-duplicators-hdus325dx-1478566081_d-2.png "Page 3
www.addonics.comTechnical Support (M-F 8:30am - 6:00pm PST) Phone: 408-453-6212 Email: www.addonics.com/support/query/
To install a 2.5” drive into the Snap-In 25 adapter:
Step 1. Gently squeeze the latches on the Snap-In 25 tray and slide it out of
the enclosure.
Step 2. Gently pull the drive retainer clips outward on the tray while inserting\
the drive from the top.
Latches")
![Page 4
Step 3. Slide the tray back into the enclosure until the latches snap into
place.
Quick Start
Note: Make sure the TARGET drive is equal to or larger than the SOURCE
drives capacity.
After installing the drives and turning on the Unit, the duplicator will\
beep,
wait for a set delay and display its firmware version. A few moments later it
will display the COPY function. Pressing ENT at this point will begin a copy
operation immediately.
www.addonics.comTechnical Support (M-F 8:30am - 6:00pm PST)...](http://img.usermanuals.tech/thumb/181/2449/w300_11-hard-drivessd-duplicators-hdus325dx-1478566081_d-3.png "Page 4
Step 3. Slide the tray back into the enclosure until the latches snap into
place.
Quick Start
Note: Make sure the TARGET drive is equal to or larger than the SOURCE
drives capacity.
After installing the drives and turning on the Unit, the duplicator will\
beep,
wait for a set delay and display its firmware version. A few moments later it
will display the COPY function. Pressing ENT at this point will begin a copy
operation immediately.
www.addonics.comTechnical Support (M-F 8:30am - 6:00pm PST)...")