Addonics Technologies 111 Hard DriveSSD Duplicators M2HDU112S User Manual

							www.addonics.com
1:9 M2 /SSD/HDD HS
Duplicator PRO
(M2HDU11-2S)
Technical Support
If you need any assistance to get your unit functioning properly, please have
your product information ready and contact Addonics Technical Support at:
Hours: 8:30 am - 6:00 pm PST
Phone: 408-453-6212
Email: http://www.addonics.com/support/query/ 
						

							Overview
 
1www.addonics.comTechnical Support (M-F 8:30 am – 6:00 pm)
WARNING: Please remember to set the power supply to your local outlet voltage prior to plugging in the power cord. Failure to do so may damage the power supply.
Power Switch
Power Connector
Power Select
Cooling Fans
Source Select 
Jumper
3.5” Source
2.5” Source
Targets
Power Button
To ControllerNot Used
2.5” Source3.5” Source
Control Panel
Source Select Jumper
NOTE: The provided jumper MUST be 
connected between “To Controller” and 
either of the two source connectors.2.5 M2 (NGFF) SSD drive (Qty. 10) 
						

							M.2 Installation
Phone: 408-453-6212Email: www.addonics.com/support/query/    2
Step 1. For 80mm device, remove 
the screw from the 80mm Standoff 
before proceeding. Otherwise, place 
Metal Standoff over mounting hole 
for 30mm, 42mm, or 60mm device.
Note: An extra screw and standoff 
are provided, when installing 60mm 
or 80mm media, remove the extra 
parts.
Step 3. Secure the device in place 
with the mounting screw.
80mm StandoffMetal Standoff 
						

							Connecting the Power Cable and Powering On
a. Connect the power cord provided from the wall outlet to the back of the tower.
b. Turn on the main power switch on the rear of the chassis.
c. Push the power button on the front of the unit to turn on the HDD duplicator.
Quick Start
By default, the duplicator will initialize, scan for drives and offer the copy function. Insert
the source and target drives, power up the unit, wait for the copy function to appear, then
press ENT.
Canceling Functions
When selecting menu options, canceling is done by pressing ESC. When the unit is busy
performing an operation such as copy, verify, or overwrite, the operation can be canceled
by holding the ESC button until the unit beeps.
Duplicator Functions
The duplicator has three menu sections: The Main menu, Setup Options, and Advanced
Setup Options. Setup Options is accessed through the Main menu. Advanced Setup
Options is accessed by holding the ESC button from any other menu until the unit beeps.
Main Menu
1. Copy HDD
Scans the ports, then copies from the source to any targets found.
2. Async Copy HDD
Scans the ports, then copies from the source to any targets found. More drives may be
added before the process is complete, they will begin the process as soon as they are
detected.
3. Compare HDD
Scans the ports, then any targets found will be compared to the source.
4. Async Compare
Scans the ports, then any targets found will be compared to the source. More drives to
compare may be added before the process is complete, they will begin the process as
soon as they are detected.
5. PreScan Source
Reads all blocks on the source drive to confirm no I/O errors are encountered.
6. ReScan BUS
Manually scans all ports and reports how many units were found.
7. Source Size
Examines the source drive and reports total space and space used, if drive contains
compatible partitions. Press up/down to change display, ESC to exit.
3www.addonics.comTechnical Support (M-F 8:30 am – 6:00 pm) 
						

							8. Secure Erase
Scans all ports, then erases all data on all connected drives.
NOTE: some drives will remain in a locked state when the process is complete. Drives that
are locked may not appear to an operating system and will cause an I/O error if used as a
target in the duplicator. If this happens, start secure erase again and hold ESC to cancel
the operation a few moments after it begins.
9. Overwrite
Overwrite is used to write data onto the entire hard disk, it will destroy all data on all HDDs
connected to the duplicator (including Source HDD) by writing data to all sectors. There
are 4 sub-options: One pass (zero), One pass (random), 3 pass and 7 pass.
10. Setup
Enters the Setup menu. See Setup Options.
11. Adv Setup
Enters the Advanced Setup Menu. Only available by holding ESC on any Main Menu
option. See Advanced Setup Options.
Setup options
10-1. Language
Use this option to select the language of the system, currently only English is supported.
10-2. Copy Size
Controls how much of the source drive to use for copy operations, in percentage. Default
setting is ALL (100%).
10-3. Startup Menu
Sets the first menu option to appear after boot. Default setting is Copy HDD.
10-4. Auto Compare
Controls whether or not targets are compared automatically when copy is complete.
Default setting is OFF.
10-5. Button Sound
Enables audible beep when pressing buttons. Default setting is ON.
10-6. Device Info
Displays information about connected drives. Main display is drive manufacturer and size.
Press up/down to select drives, ENT to display model number and firmware revision of
selected drive.
10-7. System Info
Displays firmware version and date.
Phone: 408-453-6212Email: www.addonics.com/support/query/    4 
						

							10-8. Fast Copy
When this setting is ON, the duplicator will attempt to copy the source drives contents
instead of the entire disk. Also controls Compare function. Default setting is OFF.
NOTE: Target drive size is still required to be equal to or greater than source. Only works
with source drives formatted using Master Boot Record. If the source drive has a boot
record other than MBR, the entire disk will be copied as if Fast Copy were OFF. If the
source drive is formatted with a Master Boot Record and contains only FAT32 or NTFS
partitions, identical partitions will be created on the target(s) and only the files will be
copied. If the source drive with MBR format includes partitions other than FAT32 or NTFS,
all sectors of all partitions (including FAT32 and NTFS) will be duplicated.
Enabling Fast Copy may not produce bootable duplicates.
10-9. Auto Start Drive
When source drive is present, inserting a target drive will cause copy process to begin
automatically. Default setting is OFF.
10-10. Auto Start Timer
Sets delay in time after target insertion before beginning auto copy process if Auto Start
Drive is ON. Default setting is OFF (no delay).
10-11. Tolerance Size
Sets the minimum target size in percentage compared to the source that is allowed to use
for copying. Default is 100% (equal in size).
NOTE: Leaving this setting at 100% or using for minor adjustments only is strongly
recommended. Permitting target size less than source size may result in inaccurate
copies.
10-12. BootTime Delay
This option is used to set boot delay time. Default setting is 5 seconds.
10-13. Quick Compare
Sets Compare function to stop after a small amount of data has been verified, up to
100MBytes. Default setting is OFF.
10-14. Copy with Size
Causes duplicate drive to report to an operating system the exact same total size as
source when copy is complete. Works only on drives formatted using a Master Boot
Record. Default setting is OFF.
Advanced Setup Options
11-01. Read Error Skip
Allows duplicator to ignore I/O errors while reading source drive. Default setting is OFF.
5www.addonics.comTechnical Support (M-F 8:30 am – 6:00 pm) 
						

							11-02. Update Firmware
Used to apply firmware updates. Connect a drive formatted as FAT containing one partition
with the firmware file in the root directory.
NOTE: This function scans the entire disk before proceeding. Providing a drive that is as
small as possible is strongly recommended.
11-03. Compare Firmware
Used to confirm correct firmware. Connect a drive formatted as FAT containing one
partition with the firmware file in the root directory.
NOTE: This function scans the entire disk before proceeding. Providing a drive that is as
small as possible is strongly recommended.
11-04. Quick Erase HDD
Scans the ports, then quickly erases all sectors on all connected drives.
11-05. Full Erase HDD
Scans the ports, then completely erases all sectors on all connected drives.
11-06. H/W Diagnostic
Starts comprehensive tests for Ram, LCD, buttons, ports and Flash.
11-07. Load Default
Resets all configuration settings to default.
11-08. Copy HPA
Enables copy functions to duplicate the source drives Host Protected Area. Normally this
area is defined as not available to a host controller as defined by ATA/SATA specifications.
11-09. Burn In
Runs a function continuously until aborted. Selections are Copy & Compare, Compare,
Async Cpy & Cmp, Async Compare.
Phone: 408-453-6212Email: www.addonics.com/support/query/    6 
						

							Contact Us
www.addonics.com
Phone: 408-573-8580
Fax: 408-573-8588
Email: http://www.addonics.com/sales/query/