Addonics Technologies 15 Hard DriveSSD Duplicators 1 to 5 HDDSSD Duplicator Deluxe C web User Manual

Technical Support
If you need any assistance to get your unit functioning properly, please have your 
product information ready and contact Addonics Technical Support at:
Hours: 8:30 am - 6:00 pm PST
Phone: 408-453-6212
Email: http://www.addonics.com/support/query/
v3.1.11
www.addonics.com
1:5 HDD/SSD Duplicator Deluxe C(HD5SNDXHS, HDUS5SNDX)
T E C H N O L O G I E S
User Guide         

www.addonics.comTechnical Support (M-F 8:30am - 6:00pm PST)    Phone: 408-453-6212  Email: www.addonics.com/support/query/
Drive Installation
The SOURCE drive is the Snap-In Mobile Rack, the TARGET 
drives are the remaining five units below.
1. Be sure all doors are unlocked, use the provided keys to    
    unlock if needed.
2. Gently pull the lever on the door to release it.
3. Insert the drive as shown on the label inside the door: The  
    SATA connector toward the rear. Insert the SOURCE drive...

www.addonics.comTechnical Support (M-F 8:30am - 6:00pm PST)    Phone: 408-453-6212  Email: www.addonics.com/support/query/
Connecting  th e Power  Cable a nd Powering On
a .Connect the  power cord provided f rom the wall  outlet to  the  back  of the t ower. 
b. Turn on the main power switch on the rear of the chassis.
c. Push the power button on the front of the unit to turn on the HDD dup\
licator.
The  D uplicato r P an el
T here  are four buttons  and an LCD  on the panel  of HDD  Duplic ato r.
1  –...

www.addonics.comTechnical Support (M-F 8:30am - 6:00pm PST)    Phone: 408-453-6212  Email: www.addonics.com/support/query/
Main Menu
1. Copy HDD
Scans the ports, then copies from the source to any targets found.
2. Async Copy HDD
Scans the ports, then copies from the source to any targets found. More \
drives may be added before the process is complete, they will begin the \
process as soon as they are detected.
3. Compare HDD
Scans the ports, then any targets found will be compared to the source.
4....

www.addonics.comTechnical Support (M-F 8:30am - 6:00pm PST)    Phone: 408-453-6212  Email: www.addonics.com/support/query/
9. Overwrite
Overwrite is used to write data onto the entire hard disk, it will destr\
oy all 
data on all HDDs connected to the duplicator (including Source HDD) by\
 
writing data to all sectors. There are 4 sub-options: One pass (zero), One 
pass (random), 3 pass and 7 pass.
10. Setup
Enters the Setup menu. See Setup Options.
11. View Log
Shows the results from the most recent...

www.addonics.comTechnical Support (M-F 8:30am - 6:00pm PST)    Phone: 408-453-6212  Email: www.addonics.com/support/query/
10-7. System Info
Displays firmware version and date.
10-8. Fast Copy
When this setting is ON, the duplicator will attempt to copy the source \
drives contents instead of the entire disk. Also controls Compare function. 
Default setting is OFF.
NOTE: Target drive size is still required to be equal to or greater than 
source. Only works with source drives formatted using Master Boot...

www.addonics.comTechnical Support (M-F 8:30am - 6:00pm PST)    Phone: 408-453-6212  Email: www.addonics.com/support/query/
10-14. Copy with Size
Causes duplicate drive to report to an operating system the exact same 
total size as source when copy is complete. Works only on drives format -
ted using a Master Boot Record. Default setting is OFF.
Advanced Setup Options
12-01. Read Error Skip
Allows duplicator to ignore I/O errors while reading source drive. Defau\
lt 
setting is OFF.
12-02. Update...

12-09. Burn In
Runs a function continuously until aborted. Selections are Copy & 
Compare, Compare, Async Cpy & Cmp, Async Compare.
www.addonics.com
Phone:   408-573-8580
Fax:     408-573-8588
Email:   http://www.addonics.com/sales/query/
CONTACT US