ADT Security Services BHS 3000C User Manual

Turning the System On in Motion Off/Instant Mode
1.  Close all of the doors and windows, and make sure that the  
message window reads READY or the READY light is lit  
(if not, see page 16).
2. Press the ON key. 
3. Press the MOTION OFF key. 
4. Press the INSTANT key. 
     The ON light turns on. The Premium keypad reads ON, MOTION 
OFF and INSTANT. The Standard keypad’s ON, MOTION OFF and 
INSTANT lights are lit. 
      Do not leave the building or open any protected windows  
without first turning the...

Turning the System On When It Is Not Ready 
 
If the system is not ready to turn on, you will get a “not ready” \
message. This message could mean, for example, that 
one of the protected windows in your house is open. If you have a Standa\
rd keypad, the READY light is off. If you have 
a Premium keypad, the message window reads NOT READY. 
If you press the ON key when the system is not ready to turn on, the key\
pad sounds an error tone and the system 
does not turn on. 
To make the system ready to arm...

  7.  If the READY light does not  
turn on, see the Frequently 
Asked Questions at  
www.MyADT.com, or  
call Customer Care at  
800.445.0872 for further 
assistance in correcting the 
not-ready condition.
 8.  To turn the system on, you 
must first turn off the zone that 
is not ready to arm. Press the 
OPTIONS key. 
  9. Press the 1 key. 
10.   Enter the number of the 
not-ready zone, which is the 
number of the illuminated 
light you observed in step 3. 
       CAUTION: If you bypass a 
zone, it will...

Turning the System Off 
Turning the System Off When No Alarms Are in Progress 
1.  Enter through a designated entry door. The keypad sounds a tone 
to remind you to turn the system off. The ON light blinks. 
2. Turn the system off by entering your keypad code. 
     To prevent an alarm, you must enter your code before the entry 
delay ends. See page 12 to reference the Entry Delay Time  
programmed in your system.
    Once the system is off, the ON light goes out.
1.   Enter through a designated entry...

Turning the System Off Without Canceling an Alarm
If you wish to turn off the system and report an alarm to ADT: 
1.  Enter the building through a designated entry door. The Premium 
keypad’s message window reads ALARM. The siren sounds, and 
the ON light is lit. 
2.  Enter your keypad code. The keypad beeps. Wait for ADT to call. 
Be prepared to give the ADT Customer Monitoring Representative 
your verbal Security Password. 
     Do not use the telephone if you intend to cancel the alarm. If your...

Turning the System Off after an Alarm Occurs in Your Absence
If there was an alarm at your house while you were away and the sirens a\
re no longer sounding:
1.  Enter the building through a designated entry door. The ON light 
blinks. The sirens and speakers are silent. The Premium keypad 
shows the numbers of the zones in alarm, and its message window 
reads ALARM. 
2.  Enter your keypad code to turn the system off. The keypad beeps 
once every three seconds. The keypad shows the numbers of the 
zones...

System Options
The system has five options:
1.  Bypass
2.  Door chime
3.  Additional keypad codes
4.  Alarm memory
5.  Test
This section describes each of these options. 
Bypass a Zone 
When you bypass a zone, the system ignores it. Use this feature whenever\
 you want to turn the system on, but leave 
off a particular sensor. The bypass is automatically canceled when you turn the system off. 
To bypass a zone:
1. Press the OPTIONS key. 
2. Press the 1 key. 
3. Enter the number of 
the zone you wish to...

1. Press the OPTIONS key. 
2.  Press the 2 key. 
The ENTER CODE  
light blinks.
3.  Enter your keypad code. 
The keypad beeps. The 
READY and the CHIME 
lights turn on while the 
chime feature is on. 
1. Press the OPTIONS key. 
2.  Press the 4 key. The  
ENTER CODE light 
blinks.
3.  Enter your keypad code. 
The keypad beeps. The 
lights of the zones that 
were last in alarm blink.  
1.  Press the OPTIONS 
key until the message 
window reads DOOR 
CHIME, ENTER CODE. 
2.  Enter your keypad code. 
The...

Create an Additional Keypad Code 
You can assign different keypad codes to the members of your family or t\
o people who need temporary access to 
your home. Housekeepers, guests and house sitters can all be given their\
 own keypad codes. You can assign as many 
as 91 codes, but for your security, you should limit the number of codes\
 you assign and delete any that are not in use. 
To assign a new keypad code: 
 1. Press the OPTIONS key. 
2.  Press the 3 key.  
The ENTER CODE  
light blinks. 
3.  Enter...

Delete a Keypad Code
If you wish to delete a keypad code: 
AUX CODE
KEYPAD CODE
USER NUMBERUSER NUMBER
KEYPAD CODE
AUXILIARY CODES 
ENTER MASTER 
CODE
1. Press the OPTIONS key.
2.  Press the 3 key. The  
ENTER CODE light blinks.
3. Enter your keypad code.
      The keypad beeps.  
The ENTER USER #  
light blinks. 
4.   Enter the number of  
the user whose code  
you wish to delete. The 
keypad beeps. The  
ENTER CODE light 
blinks. 
5.  Do not enter the 
keypad code. Instead, 
press the CANCEL key....